Lucent Technologies MERLIN LEGEND MDC 9000 Bedienungsanleitung

Paging Group/Page All No.

Called Party Code Called Party Code

01 13

02 14

03 15

04 16

05 17

06 18

07 19

08 20

09 21

10 22

PAGING NUMBERS

PERSONAL SPEED DIAL CODES

Loudspeaker Paging No.

Line

Zone:

COVERAGE/PICKUP/CALLING GROUPS

Group Name No. Group Name No.

Feature Codes

Account Code 82 + code +

Authorization Code 80 + code +

Callback 55

Callback Cancel ✻55

Call Waiting

pick up call waiting call ■87

Camp-On 57

Direct Voice Mail 56 + extension

Follow Me 34 + extension

Forward

inside 33 + extension

outside 33 + dial-out code

+ number +

Forward and Follow Me

cancel from all

extensions ■✻34 ✻

cancel from one

extension ■✻34 + extension

cancel from your phone 33 + your extension

Last Number Dial 84

Messaging

cancel message ■✻53 + extension

leave message 25

leave message without

calling ■53 + extension

turn off Message light

manually 54

Paging loudspeaker 9 + line number

+ zone

Personal Speed Dial ■code (01–24)

Pickup

group 88

inside 9 + extension

outside 9 + line number

Privacy

off ✻31

on 31

Reminders

set reminder 81 + time + 2 or 7

cancel reminder ✻81

System Speed Dial code (600–729)

■Available only by using feature code.

Special Characters␣

Features that dial numbers automatically may need special characters to allow for correct dialing or

system response.

Press... See... Means...

Drop s Stop. Halts dialing sequence to allow for system response.

Hold p Pause. Inserts 1.5-sec. pause in dial sequence. Multiple consecutive pauses

allowed.

Conf f Flash. Sends switchhook flash. Must be first entry in sequence.

##End of Dialing. Used to signal end of dialing sequence or to separate grouped

digits.

Document #: 555-660-138

Comcode 108196171

Issue 1, February 1998

MERLIN LEGEND®

Communications System

MDC and MDW

Telephones User’s Guide

Contents

Your MDC 9000 or MDW 9000/9010 Telephone ....................................................... 1

Describes the buttons and display

Understanding Your Telephone ......................................................................... 2

Line Button Types, Tones, Rings, Line Buttons, Using a Feature Button ..................... 3

Feature Finder .......................................................................................... 4–5

Use to choose the right feature for the activity you want to perform.

Headsets .................................................................................................... 6

Headpiece, Using Headsets

Call Handling ............................................................................................... 7

Making & Answering Calls, Conference, Hold, Transfer

Messaging ............................................................................................... 8–9

Leaving Messages, Receiving Messages........................................................... 8

Posting Messages, Signaling & Notify .............................................................. 9

Using Features ........................................................................................... 10

Feature Button, Feature Codes

Often-Used Features ................................................................................ 11–19

Account Codes, Authorization Codes ............................................................. 11

Auto Dial ............................................................................................... 12

Callback, Call Waiting .............................................................................. 13

Camp-On, Coverage, Direct Voice Mail ........................................................... 14

Do Not Disturb, Forward & Follow Me ............................................................ 15

Last Number Dial, Paging ........................................................................... 16

Park & Pickup, Personal Speed Dial .............................................................. 17

Pickup, Privacy, Recall ............................................................................. 18

Reminders, Saved Number Dial, System Speed Dial ............................................ 19

Troubleshooting ..................................................................................... 20–21

Solving Common Problems

Programming Buttons & Settings ................................................................. 22–23

Programming Buttons, Programming Settings, Special Characters ......................... 22

Programming Codes .................................................................................. 23

Pull-Out Card

Remove this and use it to keep track of speed dial codes, group numbers, and other .....

information about your phone and system.

Transtalk CoversR6 1/28/98, 11:00 AM1

Security Alert

Your Responsibility for Your System’s Security␣

Toll fraud, the unauthorized use of your telecommunications system by an unauthorized party (for example,

persons other than your company’s employees, agents, subcontractors, or persons working on your

company’s behalf) can result in substantial additional charges for your telecommunications services. You

are responsible for the security of your system. There may be a risk of toll fraud associated with your

telecommunications system. Your system administrator should read all installation, instruction, and

system administration documents provided with this product to fully understand the features that can

introduce the risk of toll fraud and the steps that can be taken to reduce that risk. Lucent Technologies

does not warrant that this product is immune from or will prevent unauthorized use of common-carrier

telecommunication services or facilities accessed through or connected to it. Lucent Technologies will not

be responsible for any charges that result from such unauthorized use.

Called Party Code Called Party Code

Message Code Message Code

01 11

02 12

03 13

04 14

05 15

06 16

07 17

08 18

09 19

10 20

DO NOT DISTURB

OFTEN-USED SYSTEM SPEED DIAL CODES

POSTED MESSAGES

Transtalk CoversR6 1/28/98, 11:00 AM2

ON MSG

RANGE BATT

PSTAT18

1823

6 5

-Handset Display-

Your MDC 9000 or MDW 9000/9010 Telephone

1 — Line Status Indicators show status of

outside and inside lines. Arrow or rectangle

“points” to the line button it represents and

flashes in different patterns to show activity

on the line (see box below).

2 — P appears when in program mode.

3 — STAT (MDC 9000 only) appears steady-on

when handset is out of range. Remains until

all line status indicators are updated.

MUTE (MDW 9000/9010 only) appears when

the handset microphone is off.

4 — MSG appears when you have received a voice

mail message.

5 — BATT appears when there are only a few

minutes of conversation time left. Handset

gives 2 short beeps. Place handset on the

base to recharge.

6 — RANGE appears (and handset beeps twice)

if Status (off only) or On/Off button is

depressed when handset is out of the base’s

range. To make or receive calls, move

handset closer to base.

7 — ON appears when the handset is turned on

after you pressed On/Off.

8 — 18 (MDW 9010 only) indicates Local Test

Mode; 1through 10 are used in Wireless

Test Mode.

To Update Display:

Press

Two Loud Beeps

means

Move Closer to Base Unit

Status

ON MSG

RANGE BATT

PSTAT

Status

On/Off

Hold

ABC

DEF

MNO

WXYZ

JKL

PQRS

Oper

GHI

Conf Trans Feat

TUV

Ext.

MDC 9000

STAT/RANGE

means

Move Closer to Base Unit

User Instructions

(MDC 9000) A quick reference

to most important cordless

phone features.

Directory Card

(MDC 9000, behind cover)

Antenna

Headset Jack

(MDC 9000) For headset adapter

cord.

Battery Charging

Contacts

Handset batteries charge through

these contacts. Clean periodically

by rubbing them with a soft gum

eraser.

Status

(MDC 9000) Press to turn on the

display when the handset is off,

or to update the display when the

STAT indicator appears.

Volume Control

(MDC 9000) Slide the switch to

adjust the volume of the earpiece to

Normal or High.

(MDW 9000/9010) An 8-interval

pushbutton controls the ringer

volume when the phone is off and

the receiver volume when the

phone is on.

Mute

(MDW 9000/9010) Press to turn

the microphone on/off so that

you can/cannot be heard by the

caller.

Conf (Conference)

Press to add another party to

your call (see p. 7).

Headset Jack

(MDW 9000/9010) For headset

adapter cord.

Feat (Feature)

Press to enter program mode

(see p. 22).

Handset Extension

Label

Write the extension number

on this label using a pencil

or ballpoint pen only.

Trans (Transfer)

Press to transfer a call to

another extension (see p. 7).

Handset Display

Displays status of lines and

range. For details, see figure

opposite.

Outside Line/

Programmable/

Intercom/ Drop

Buttons (6)

See Line Buttons,

p. 3, for line button

assignments.

Hold

Press to put a call on hold

(see p. 7).

On/Off

To turn the handset on, press

once. ON appears in the

display. To turn off, press

again. Turn on to make or an-

swer a call, and turn off to hang

up (see p. 7).

Flash Long on, long off indicates a ringing call.

Wink Long on, short off indicates a call on hold.

indicates the line you’re using.

-Line Status Indicators-

Arrows ( or ) indicate the next available line.

Rectangle ( ) indicates activity at any extension.

Steady on indicates a busy line.

Off continuously indicates an idle line.

Note: This quide covers the MDC 9000, MDW 9000, and MDW 9010. The picture shows the MDC

9000. The differences are as follows:

Instead of a Status button, the MDW 9000 and MDW 9010 have a Mute button. Press the Mute

button to turn the handset and headset microphone off for privacy while having a conversation.

The Headset jack on the MDW 9000 and MDW 9010 is located at the bottom of the handset, above and

to the left of the Handset Extension Label.

Headset On/Off Button

Press to turn the headset on and

off.

Understanding Your Telephone

␣Line Button Types␣

See Line Buttons, p. 3, for the location and definition of line buttons on your handset.

␣ Tones␣

Tone Meaning

Dial tone (steady) You can make a call.

Busy (slow repeating tone) The phone you are calling is busy.

Fast busy (fast repeating tone) No lines are available.

Error (alternating high-low tones) You dialed a number or used a feature incorrectly.

Confirmation (double break in You used a feature correctly.

dial tone followed by steady tone)

Callback (5 short beeps) This call is receiving Callback treatment (see p. 13).

Call Waiting (1 or 2 beeps) You have an inside (1 beep) or an outside (2 beeps)

call waiting (see p. 13).

␣ Rings␣

The table below helps you identify the different types of ringing. You can also personalize ringing at your

telephone or adjust ring timing for the line buttons where calls arrive. Programming Buttons &

Settings, p. 22, tells you how to change the settings. Listed below are your options:

•Personalized Ring. (MDW 9000/9010 only) Allows you to give calls ringing at your phone one of

eight distinctive rings.

•Abbreviated Ringing. When you are on a call and another call arrives at your phone, you can use

this feature to give the second call a short ring.

•Immediate Ring. Calls ring immediately on line buttons set this way.

•Delay Ring. This setting causes calls to ring at your phone after a delay. If your calls are being

covered, this allows time for another person to answer a call before you do.

•No Ring. Calls do not ring (except for returning transferred and Callback calls). Calls on lines set for

No Ring do not receive coverage (p. 14).

•Send Ring. Usually, when a call comes in on an SA button, it rings there immediately and rings at

corresponding SSA buttons after a delay, giving the person with the SA button time to answer before

the call is picked up by someone with a corresponding SSA button. When busy on another call, the

person with the SA button can use the Send Ring setting to make calls arriving at other SA buttons

ring

immediately

on corresponding SSA buttons.

Ring Meaning

1 long ring Inside call or returning Callback call (see p. 13) on

MDC 9000

1 short ring and 1 long ring Outside call

2 short rings and 1 long ring Outside call is transferred to you, returning transferred

call, or returning Callback call (see p. 13) on

MDW 9000/9010

All Telephones

NNN-XXXX

Make/receive outside calls only.

Telephones with ICOM Buttons

ICOM Ring Make/receive inside ringing calls.

ICOM Voice Make inside voice-announced calls

and receive inside ringing calls.

ICOM Make (not receive) inside calls

Originate only.

Only

Telephones with System Access (SA) Buttons

SA buttons give you access to inside or outside lines

for making and/or receiving calls. To make an outside

call on an SA button, first dial the dial-out code

(usually 9) that your system manager supplies. No

dial-out code is necessary when you call another

extension.

SA Ring Make/receive inside/outside ringing

calls.

SA Voice Make/receive outside calls; receive

inside ringing calls; make inside

voice-announced calls.

SA Originate Make (not receive) inside and

Only outside calls.

Shared SA Make/receive calls for co-workers or

(SSA) join conversations. The line is shared

with another co-worker(s). One

person has an SA button that is

shared with one or more others who

have SSA buttons corresponding to

it. See Rings for information about

how calls ring at these buttons.

Pool Make/receive outside calls only. Use

the dial-out code supplied by your

system manager.

CAUTION:

To clean your phone, unplug it from the wall jack (if applicable) and use a

slightly

dampened cloth. To

prevent permanent damage, do not immerse the phone in water or any liquid, and do not use liquid or

aerosol cleaners directly on the telephone.

␣Line Buttons␣

The lower buttons are programmed as shown below. 3,4, and 5 are programmable line buttons

that you can program with features (p. 22). One may be programmed as a Feature button

(p. 10) if you enter account codes (p. 11) during calls.

ON MSG

RANGE BATT

PSTAT18

DROP

ICOM/SA

(R)

ICOM/SA

(V)

543

The Voice Announce setting should be turned off because the handset does not have a speaker

function. The system manager can turn Voice Announce off at your extension through system

programming.

To turn Voice Announce off with your handset:

1. Turn the phone on and press the imprinted Feat button; then dial 00.

2. Press any ICOM or SA button.

3. Dial ✻✻10.

4. Press the imprinted Feat button; then dial 00 to exit program mode.

You cannot be assigned to a paging group.

Ringing options should be used with caution.

␣Using a Feature Button␣

To use many system features, you can either program a Feature button or dial

before entering a

feature code. You only need a programmed Feature button in order to enter account codes (p. 11)

during calls. For details about programming a Feature button, see p. 10. If a Feature button is

programmed, there will be two Feature buttons on the handset:

• The programmed Feature button. If you choose to program a Feature button, use the top right

line button for this purpose (button 5, above).

• The factory-set imprinted Feat button (see p. 1) on the handset, located beneath the dialpad.

This imprinted Feat button is used to program buttons and settings (see p. 22).

Throughout this book, we refer to the programmed Feature button. The telephone Feat button used

to enter program mode is the imprinted Feat button.

Feature Finder

This table shows where to look for information about performing specific telephone activities. Any

features that do not have detailed instructions can be used by following the directions in Using

Features (p. 10) or programmed by following the instructions in Programming Buttons &

Settings (p. 22).

Calling

If you want to ... Then

Dial numbers with the touch of a button. See Auto Dial, p. 12.

Program codes for numbers you dial often. See Personal Speed Dial, p. 17.

Quickly dial numbers your company has programmed. See System Speed Dial, p. 19.

Make a voice-announced call to 1 or more co-workers. Use an ICOM Voice or SA Voice button (Line

Button Types, p. 2) and see also Paging, p. 16.

Broadcast over the company’s loudspeaker system. See Paging, p. 16.

Make and answer calls with no hands. For information about a headset, see p. 6.

Automatically redial a number you dialed before. See Last Number Dial, p. 16, and Saved

Number Dial, p. 19.

Connect to an extension or outside line when it’s See Callback, p. 13.

free (phones with SA buttons only).

Enter an account code before or during a call. See Account Codes, p. 11.

Know if someone is calling you when all your other See Call Waiting, p. 13.

lines are in use.

Disconnect the call you’re on without hanging up. See Recall, p. 18.

Set up a conference with as many as 4 others. See Conference, p. 7.

Transfer a call. See Transfer, p. 7, and Park & Pickup, p. 17.

Reach a voice mailbox without calling the person. See Direct Voice Mail, p. 14.

Make a call from another extension, using your own See Authorization Codes, p. 11.

calling privileges.

Put a call on hold. See Hold, p. 7.

Customizing Your Phone

Program a feature on an unused line button. See Programming Buttons & Settings, p. 22.

Adjust volume of the earpiece or ringer. See p. 1.

Give your phone its own distinctive ring See Rings, p. 2.

(MDW 9000/9010 only).

Delay or remove the ring from an outside, SA, or See Rings, p. 2, and Coverage, p. 14.

ICOM line button.

Covering Calls

If you want to ... Then

Have a co-worker answer your calls. See Coverage, p. 14,

Answer all of a co-worker’s calls from your telephone.

Stop your calls from being covered by others.

Stop your outside calls from going to your company’s See Coverage, p. 14.

voice mail system (or send calls to voice mail).

Forward your calls to another telephone. See Forward & Follow Me, p. 15.

Answer your calls from another extension.

Answer a call ringing at a co-worker’s extension. See Pickup, p. 18.

Answer a call on a line that’s not on your phone.

Put a call on hold at a busy extension until your If your phone system doesn’t have voice mail,

co-worker is ready for it or complete a transfer to an see Camp-On, p. 14.

extension that doesn’t answer.

Hold a call when you’re trying to transfer it and your See Park & Pickup, p. 17.

co-worker doesn’t answer; page your co-worker while

the call waits.

Messaging

Let a co-worker know you called. See Messaging, pp. 8–9.

Find out if you have a voice mail message, fax, or

other message.

Signal a co-worker to contact you.

Choose a message to leave for co-workers who have

display phones.

Reach a voice mailbox without calling the person. See Direct Voice Mail, p. 14.

Privacy

Prevent interruptions by blocking calls to your phone. See Do Not Disturb, p. 15.

Prevent co-workers from joining your calls. See Privacy, p. 18.

Timekeeping

Remind yourself of appointments. See Reminders, p. 19.

Feature Finder

and Line Button Types, p. 2.

␣Headpiece␣

Your Lucent Technologies cordless or wireless phone is equipped with a single-prong headset jack on

the left, near the volume control switch (MDC 9000), or on the bottom, near the extension label (MDW

9000/9010).

Your headset assists in call answering and provides hands-free operation.

The headpiece provides sound in one ear. It has an adjustable headband and soft ear cushion. The

noise-canceling microphone reduces background noise by up to 75%.

Important: The range of the handset is diminished when you are using the headset. Therefore, you

may need to move closer to the base, or move the base closer to your operating area.

Headsets

␣Using Headsets␣

When using a headset, the 12-inch (30-cm)

headset adapter cord is required. The “quick

disconnect” plug on the headset adapter cord

attaches to the headset. The headset adapter

miniplug is then inserted into the headset jack

on the handset.

If desired, the headset adapter cord can be

removed from the handset without the call

being dropped. You can then use the handset

as you normally would.

Note: Calls cannot be heard on the handset

when the headset adapter cord is connected to

the headset jack. The handset microphone is

also disabled.

Answering Calls with a Headset

For convenience when using the holster, the

headset On/Off button near the antenna should

be used. This button will become active only

when the headset adapter cord is plugged into

the headset jack. It is identical in function to the

On/Off button to the left of the Hold button.

When you receive a call, you hear ringing

coming from the handset; you do not hear a

tone from the headset itself. To answer a call,

activate the headset On/Off button near the

antenna, or if you prefer, the On/Off button

to the left of the Hold button (if the handset is

not in the holster).

Placing Calls with a Headset

To place a call with a headset:

1. Remove the handset from the holster.

2. Press the On/Off button to access an

available line.

3. Dial the number as described in Making &

Answering Calls, p. 7.

ICOM Line 4

Line 3Line 2Line 1

ICOM

ON MSG

RANGE BATT

PSTAT

Mute On/Off Hold

ABC

DEF

MNO

WXYZ

JKL

PQRS

Oper

GHI

Conf

Trans

Feat

TUV

MDC 9000

Ext.

CAUTION:

Do not plug any other devices

into the headset jack.

Headset Jack

(MDC 9000)

Headset Jack

(MDW 9000/9010)

Quick

Disconnect

Plug

Headset

Adapter

Cord

Call Handling

␣Making & Answering Calls␣

First, review pp. 1–2 to find out about the buttons, tones, and rings on your telephone. If you have

a headset, see p. 6. In this guide, instructions for using features may not include all the possible

ways you can make a call.

To make a call

, press the On/Off button. A line button is automatically selected for you. To make a

call on a specific line (for example, an SA or ICOM line for a voice-announced call), select an idle

line button and press it before pressing the On/Off button.

To answer a call

, press the On/Off button.

␣Conference␣

A conference call can have up to three inside

participants, including yourself and up to two

outside participants.

1. Dial the first outside number or extension.

Announce the call.

2. Press the Conf button to put the call on

hold.

3. Select an ICOM, SA, or numbered line

button.

4. Dial the next number or extension.

5. Announce the call and press Conf.

6. Repeat Steps 2–5 for each participant.

• Press the Drop button and line button to

drop any participant added.

• Press the Hold button to temporarily

leave the conference. Then press any

participant’s line button to rejoin the

conference.

7. To end the conference, hang up.

SECURITY ALERT:

If the system selects an SA Voice button

when you add a conference participant, you

hear a beep instead of ringing after you dial

the extension. If the call is not answered and

you press the Conf button to complete the

call, your conversation with other conference

participants is broadcast on the extension’s

speakerphone. To prevent this, be sure to

drop an unanswered extension that you’ve

called on an SA Voice button.

␣Hold␣

When you have a call or conference on hold,

your phone beeps once each minute.

1. Press the Hold button to put a call on hold.

(Do not press Drop to end a conference

while the call is on hold.)

2. To return to the call or conference, press

the winking ICOM, SA, or line button that is

holding the call.

␣Transfer␣

To transfer:

1. Press the Trans button. The system selects

an ICOM or SA button and puts the call on

hold.

2. Dial the extension or the outside number.

3. Announce the call if desired.

4. Press the Trans button or hang up. To

cancel the transfer or return to the call on

hold, press the winking ICOM, SA, or line

button.

To one-touch manual transfer:

1. Press the programmed Auto Dial button

(p. 12) for the number where you want to

transfer the call.

2. Announce the call.

3. Press the Trans button or hang up. To

cancel the transfer or return to the call on

hold, press the ﬂashing button.

To one-touch auto transfer if available:

Press the programmed Auto Dial button.

Messaging

Your phone system has several features that allow you to leave messages for others in your office. If you

use Leave Message or Posted Messages, the person(s) for whom you are leaving a message must have

a display phone. If you wish to leave a message for a person who does not have a display telephone,

use voice mail and the Direct Voice Mail feature (p. 14), if available, or ask the system operator to take a

message for the person. Here are some guidelines for different messaging features:

•Leave Message. This feature simply lets a co-worker know you have called. The message shows

your name and the date and time of your call. If you leave one message and then another, the second

message replaces the first.

•Posted Messages. If you post a message at your telephone, inside callers with display phones

see the posted message you have selected. As many as 20 messages may be available for posting.

If a message is waiting for you, MSG appears on your display when you turn on your phone. The

descriptions below explain how to read, cancel, and delete messages you have sent or received.

If your company has voice mail, ask your system manager for details about using the voice mail system.

For information about having your phone covered by the voice mail system, see Coverage, p. 14.

If you frequently communicate with a small number of people, there are two features you can use, both

of which require programming on a button. These are Signaling and Notify, described on p. 9.

␣Leaving Messages␣

To program:

See Programming Buttons & Settings, p. 22.

To leave a message at a busy or unanswered

extension you are calling:

• Press the Leave Message button you

have programmed, OR

Press

or the programmed Feature

button and dial 25.

• To leave a voice mail message (if your

company has such a system), press

the programmed Feature button and

dial 56 (see p. 14 for details).

To leave a message without calling:

1. Press

or the programmed Feature button

and dial 53.

2. Dial the extension.

To cancel a message:

1. Press

or the programmed Feature button

and dial ✻53.

2. Dial the extension.

␣Receiving Messages␣

If MSG appears on your display when you turn

your phone on, you have a message from the

system operator. Depending on how your

system is set up, you may also have a voice

mail message or a fax.

Call your system operator for the message or

ask your system manager how to retrieve a

voice mail message.

To remove the message indicator, press

the programmed Feature button and dial 54.

Andere Handbücher für MERLIN LEGEND MDC 9000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lucent Technologies Telefon Handbücher

Lucent Technologies

Lucent Technologies Index Bedienungsanleitung

Lucent Technologies

Lucent Technologies 2500 EMGP Bedienungsanleitung

Lucent Technologies

Lucent Technologies index 2030 Bedienungsanleitung

Lucent Technologies

Lucent Technologies 302A Bedienungsanleitung

Lucent Technologies

Lucent Technologies Merlin Legend MLX-10D Bedienungsanleitung

Lucent Technologies

Lucent Technologies Definity Callmaster II Bedienungsanleitung

Lucent Technologies

Lucent Technologies Definity 6408D+ Bedienungsanleitung

Lucent Technologies

Lucent Technologies 4400 series Bedienungsanleitung

Lucent Technologies

Lucent Technologies 9630 Bedienungsanleitung

Lucent Technologies

Lucent Technologies Merlin Legend MLX-5 Bedienungsanleitung

Lucent Technologies

Lucent Technologies 8101 Bedienungsanleitung

Lucent Technologies

Lucent Technologies MDW 9030P Kurzanleitung

Lucent Technologies

Lucent Technologies 6201 Bedienungsanleitung

Lucent Technologies

Lucent Technologies 4406D Bedienungsanleitung

Lucent Technologies

Lucent Technologies DT3 Bedienungsanleitung

Lucent Technologies

Lucent Technologies Galilee 960a Bedienungsanleitung

Lucent Technologies

Lucent Technologies ISDN 970 Bedienungsanleitung

Lucent Technologies

Lucent Technologies 954 Bedienungsanleitung

Lucent Technologies

Lucent Technologies DSS/BLF Bedienungsanleitung

Lucent Technologies

Lucent Technologies Definity 8434DX Bedienungsanleitung

Lucent Technologies

Lucent Technologies MERLIN LEGEND MDC 9000 Bedienungsanleitung

Lucent Technologies

Lucent Technologies 6400 Series Bedienungsanleitung

Lucent Technologies

Lucent Technologies Definity 8403 Bedienungsanleitung

Lucent Technologies

Lucent Technologies MERLIN LEGEND Release 3.1 Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

D-Link

D-Link DWR-720/PW Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

AT&T

AT&T Trimline 205 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Panasonic

Panasonic KX Series Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung