M-system R5-SS Bedienungsanleitung

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

DC current input module .................................................. (1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■HOT INSERTION/REMOVAL OF MODULES

• Removing or replacing modules does not affect other mod-

ules on the same backplane. It is possible to replace them

without removing the power supply. However, replacing

multiple modules at once may greatly change line voltage

levels. We recommend that you replace them one by one.

■GENERAL PRECAUTIONS

• DO NOT set the switches while the power is supplied.

The switches are used only for maintenance without the

power.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

INSTALLATION

Use the Installation Base (model: R5-BS).

DC CURRENT INPUT MODULE MODEL R5-SS

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp EM-6143 Rev.2 P. 1 / 3

INSTRUCTION MANUAL

COMPONENT IDENTIFICATION

Euro Type

Connector Terminals

RUN LED

456

123

Input 1 Input 2

2345678

RUN

■

SIDE VIEW ■FRONT VIEW

■STATUS INDICATOR LED

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

■SIDE DIP SW

• Input Range: SW1 through 8

Each channel independent

RANGEINPUT 1 INPUT 2

12345678

OFF OFF OFF OFF OFF OFF OFF OFF -40 – +40mA

ON OFF OFF OFF ON OFF OFF OFF -20 – +20mA

OFF ON OFF OFF OFF ON OFF OFF -1 – +1mA

ON ON OFF OFF ON ON OFF OFF 0 – 40mA

OFF OFF ON OFF OFF OFF ON OFF 0 – 20mA

ON OFF ON OFF ON OFF ON OFF 4 – 20mA (*)

OFF ON ON OFF OFF ON ON OFF 0 – 1mA

(*) Factory setting

PC CONFIGURATOR

With conﬁgurator software, settings shown below are available.

Refer to the software manual of R5CON for detailed operation.

■CHANNEL INDIVIDUAL SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Zero Scale -32000 to +32000 0

Full Scale -32000 to +32000 10000

Bias [Zero Adj.] -320.00 to +320.00 0.00

Gain [Span Adj.] -32000 to +32000 1.0000

R5-SS

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp EM-6143 Rev.2 P. 2 / 3

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm (inch)

456

123

6.5

(.26)

90 (3.54) LOCKING CLAMP

90 (3.54) 5.6

(.22)

18 (.71)

POSITIONING GUIDE

*Euro type connector terminals (4, 5 and 6) provided only with 2-ch. option.

■CONNECTION DIAGRAM

BUS CONNECTOR

INTERNAL

POWER

*For dual redundant communication.

Note: Connect either wide or narrow span terminals for each channel.

The section enclosed by broken line is with 2-ch. option.

–

NARROW SPAN

WIDE SPAN

NARROW SPAN

WIDE SPAN

INPUT 1

–

INPUT 2

INTERNAL

BUS A

INTERNAL

BUS B*

• Wide span: -40 – +40 mA DC, -20 – +20 mA DC,

0 – 40 mA DC, 0 – 20 mA DC, 4 – 20 mA DC

• Narrow span: -1 – +1 mA DC, 0 – 1 mA DC

WIRING INSTRUCTIONS

■EURO TYPE CONNECTOR TERMINAL

Applicable wire size: 0.2 to 2.5 mm2

Stripped length: 7 mm

R5-SS

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp EM-6143 Rev.2 P. 3 / 3

Andere M-system E/A-System Handbücher

M-system

M-system R7K4F Series Bedienungsanleitung

M-system

M-system Remote I/O R8 Series Bedienungsanleitung

M-system

M-system R8-DCM16ALZ Bedienungsanleitung

M-system

M-system R7G4FML3-6-DA16 Bedienungsanleitung

M-system

M-system R7HL-PA4E Bedienungsanleitung

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system EtherCAT R7I4DECT-1-YVF4 Bedienungsanleitung

M-system

M-system R7C-EA16 Bedienungsanleitung

M-system

M-system R3-CT8A Bedienungsanleitung

M-system

M-system Mini-MW Series Bedienungsanleitung

M-system

M-system R7C-DA16 Bedienungsanleitung

M-system

M-system R7ML-RS4 Bedienungsanleitung

M-system

M-system R7C-DS4N Bedienungsanleitung

M-system

M-system R7G4HML-6-SVF8N Bedienungsanleitung

M-system

M-system R3Y-DC16 Bedienungsanleitung

M-system

M-system R5-SV Bedienungsanleitung

M-system

M-system R7I4DML3-DA32A Bedienungsanleitung

M-system

M-system R3-DA8C Bedienungsanleitung

M-system

M-system JC-IO Bedienungsanleitung

M-system

M-system R7ML-DC16A-R Bedienungsanleitung

M-system

M-system Devicenet R7F4HD-DA32B Bedienungsanleitung

M-system

M-system R80UST4 Bedienungsanleitung

M-system

M-system R3-US4 Bedienungsanleitung

M-system

M-system 6BSN Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

WAGO

WAGO I/O-SYSTEM 750 Bedienungsanleitung