Manitowoc MLC165 1 Series Bedienungsanleitung

Manitowoc Cranes

9304-AM, 2015-11-09

Manitowoc, Wisconsin 54220 U.S.A.

1/3

MLC165

Luffing Jib Raising Procedure

Luffing Jib No. 135 on Boom No. 74

Recommended boom and luffing jib raising and lowering procedure

MLC165 SERIES 1 must be equipped with 45 130 kg crane counterweight and 0 kg carbody counterweight; MLC165

SERIES 2 must be equipped with 55 110 kg crane counterweight and 16 010 kg carbody counterweight. Refer to luffing

jib rigging assembly No. 81022481 for boom and luffing jib make-up of inserts, pendants, struts, strut raising and

lowering procedure, jib stop setup and operation and miscellaneous parts, etc. Refer to Operator’s Manual for setup and

installation.

Boom and luffing jib combinations must be raised and lowered using jack-knife method.

Caution: Anytime luffing jib point rollers are in contact with ground during raising or lowering procedure, disengage

swing lock if equipped, and release swing brake.

Raising:

Luff up jib strut to keep luffing jib strut off luffing jib during boom raising. Slowly raise boom while luffing jib point wheels

are allowed to roll on ground. When luffing jib stop strut is just clear of ground, attach luffing jib stop pendants and unpin

luffing jib stop inner strut from retracted position. Slowly raise boom until luffing jib stop strut is fully extended and pins

engaged (approximately 168 degree boom-to-luffing jib angle). Continue to boom up with luffing jib wheels rolling on

ground until boom-to-luffing jib angle reaches value specified in Tables 1 and 2 or vertical, whichever occurs first.

Tighten luffing jib suspension with luffing jib hoist. Boom and luffing jib are then raised together using boom hoist until

boom reaches desired boom operating angle. Luffing jib radius must be within capacity chart before swinging over side

of machine when raising over front of blocked crawlers.

Lowering:

Position boom at 85 degrees prior to lowering luffing jib. Lower luffing jib until boom-to-luffing jib angle reaches value

specified in Tables 1 and 2. Lower boom until luffing jib point wheels contact ground. If luffing jib is hanging vertical, raise

luffing jib a few degrees forward of vertical. Continue to lower boom while luffing jib wheels roll along ground. Keep

enough tension on luffing jib hoist to keep luffing jib strut off luffing jib. Stop lowering boom when luffing jib stop pendants

start to go into tension (approximately 168 degree boom-to-luffing jib angle). Disengage luffing jib stop strut pins and

lower boom to retract luffing jib stop inner strut. Pin strut in retracted position.

Caution: Do not under any condition allow boom to luffing jib angle to become less than 60 degrees.

REFERENCE ONLY!

9304-AM, 2015-11-09

Manitowoc Cranes

2/3

Manitowoc, Wisconsin 54220 U.S.A.

MLC165

Luffing Jib Raising Procedure

Luffing Jib No. 135 on Boom No. 74

Refer to Tables 1 and 2 for raising ability with the maximum weight of load blocks, hooks, weight balls,

slings and hoist lines beneath boom and jib point sheaves. Raising with blocks requires luffing jib wire

rope guard per delta note 36 on rigging drawing. For block weights shown with #, load blocks, hooks,

weight balls and slings must remain on ground until combined weights are within rated capacity of chart.

Table 1

MLC165 SERIES 1

Boom

Length

Boom to

Luffing

Jib Angle

Over Front of Blocked Crawlers Over End or Side of Crawlers

Boom to

Luffing Jib

Angle

Weight Under Load Point

Boom Jib Boom Jib Boom Jib Boom Jib

# # 2 760 kg 1 040 kg # # 2 760 kg 1 040 kg

Meters Degrees Luffing Jib Length - Meters Degrees

21,0 168 21,3 - 51,8 21,3 - 36,6 21,3 - 39,6 21,3 - 27,4 168

90 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 90

60 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 60

24,0 168 21,3 - 45,7 21,3 - 30,5 21,3 - 33,5 — 168

90 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 90

60 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 60

27,0 168 21,3 - 36,6 21,3 21,3 - 27,4 — 168

90 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 90

60 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 60

30,0 168 21,3 - 30,5 —21,3 — 168

90 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 39,6 90

60 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 60

33,0 168 21,3 - 24,4 — —— 168

90 21,3 - 51,8 21,3 - 48,8 21,3 - 51,8 —90

60 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 33,5 60

36,0 90 21,3 - 51,8 — 21,3 —90

60 21,3 - 51,8 21,3 - 45,7 21,3 - 51,8 —60

39,0 90 21,3 - 45,7 ———

60 21,3 - 51,8 ———

(a)42,0 60 21,3 - 51,8 — ——

(a) Requires lower boom point to be removed.

REFERENCE ONLY!

Manitowoc Cranes

9304-AM, 2015-11-09

Manitowoc, Wisconsin 54220 U.S.A.

3/3

MLC165

Luffing Jib Raising Procedure

Luffing Jib No. 135 on Boom No. 74

Table 2

MLC165 SERIES 2

Boom

Length

Boom to

Luffing Jib

Angle

Over Front of Blocked Crawlers Over End or Side of Crawlers

Boom to

Luffing Jib

Angle

Weight Under Load Point

Boom Jib Boom Jib Boom Jib Boom Jib

# # 2 760 kg 1 040 kg # # 2 760 kg 1 040 kg

Meters Degrees Luffing Jib Length - Meters Degrees

21,0 168 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 42,7 168

90 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 90

60 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 60

24,0 168 21,3 - 51,8 21,3 - 45,7 21,3 - 48,8 21,3 - 36,6 168

90 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 90

60 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 60

27,0 168 21,3 - 51,8 21,3 - 39,6 21,3 - 42,7 21,3 - 27,4 168

90 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 90

60 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 60

30,0 168 21,3 - 48,8 21,3 - 33,5 21,3 - 36,6 21,3 168

90 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 90

60 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 60

33,0 168 21,3 - 42,7 21,3 - 24,4 21,3 - 30,5 — 168

90 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 90

60 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 60

36,0 168 21,3 - 33,5 — 21,3 - 24,4 —168

90 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 39,6 90

60 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 60

39,0 168 21,3 - 27,4 ———

168

90 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 — 90

60 21,3 - 51,8 21,3 - 51,8 21,3 - 51,8 21,3 - 45,7 60

42,0 168 21,3 ———

168

90 21,3 - 51,8 — 21,3 - 39,6 — 90

60 21,3 - 51,8 21,3 - 39,6 21,3 - 51,8 — 60

45,0 90 21,3 - 51,8 — — — 90

60 21,3 - 51,8 — 21,3 - 45,7 —60

48,0 60 21,3 - 51,8 ———

(a)51,8 60 21,3 - 51,8 ———

(a) Requires lower boom point to be removed.

REFERENCE ONLY!

Dieses Handbuch passt für folgende Modelle

Andere Manitowoc Baumaschinen Handbücher

Manitowoc

Manitowoc Grove RT890E Bedienungsanleitung

Manitowoc

Manitowoc GROVE GMK Benutzerhandbuch

Manitowoc

Manitowoc National Crane NBT40-1 Series Bedienungsanleitung

Manitowoc

Manitowoc Grove GMK 5200-1 Bedienungsanleitung

Manitowoc

Manitowoc Grove TMS700E Installations- und Benutzerhandbuch

Manitowoc

Manitowoc Grove GRT9165 Bedienungsanleitung

Manitowoc

Manitowoc 16000 Bedienungsanleitung

Manitowoc

Manitowoc Grove 5540F Bedienungsanleitung

Manitowoc

Manitowoc MLC300 Bedienungsanleitung

Manitowoc

Manitowoc 999 Installations- und Benutzerhandbuch

Manitowoc

Manitowoc GROVE GMK5150L Bedienungsanleitung

Manitowoc

Manitowoc GHC 55 Betriebsanleitung

Manitowoc

Manitowoc Grove RT9130E-2 Installations- und Benutzerhandbuch

Manitowoc

Manitowoc 1800 Bedienungsanleitung

Manitowoc

Manitowoc 16000 Bedienungsanleitung

Manitowoc

Manitowoc MLC300 Bedienungsanleitung

Manitowoc

Manitowoc National Crane 1400A Bedienungsanleitung

Manitowoc

Manitowoc GROVE GMK3060 Bedienungsanleitung

Manitowoc

Manitowoc 14000 Bedienungsanleitung

Manitowoc

Manitowoc 2250 Bedienungsanleitung

Manitowoc

Manitowoc Grove RT9150E Bedienungsanleitung

Manitowoc

Manitowoc National Crane 1300A Bedienungsanleitung

Manitowoc

Manitowoc GHC 75 Technische Daten

Manitowoc

Manitowoc Grove RT880E Installations- und Benutzerhandbuch

Beliebte Baumaschinen Handbücher anderer Marken

SASFORKS

SASFORKS EXTREME Bedienungsanleitung

Hailo

Hailo H-50 Bedienungsanleitung

Graco

Graco LineLazer ES 1000 Gebrauchs- und Pflegehandbuch

Greenlee

Greenlee 555RSC Bedienungsanleitung

Lux Tools

Lux Tools A-FMR-20 Set Bedienungsanleitung

SIP

SIP 03683 Bedienungsanleitung

Volvo

Volvo L30G Bedienungsanleitung

Grizzly

Grizzly G8712 Bedienungsanleitung

Modulift

Modulift CMOD 12 Bedienungsanleitung

Case

Case DV201 Bedienungsanleitung

Sealey

Sealey SC10.V2 Bedienungsanleitung

Wacker Neuson

Wacker Neuson DT05 Bedienungsanleitung

HYVA

HYVA AMCO VEBA 81 Series Bedienungsanleitung

Atlas Copco

Atlas Copco Dynapac V5100TV Bedienungsanleitung

Toro

Toro 323 Bedienungsanleitung

SGS

SGS EC1500 Bedienungsanleitung

Saferoad

Saferoad VR Arcus Primus 90 Series Bedienungsanleitung

Turbosol

Turbosol BM 30 Bedienungsanleitung