Marshall Amplification JMP-1 Bedienungsanleitung

JMP-1

Valve Midi

Pre-amp

Handbook

Marshall Amplification plc

Denbigh Road, Bletchley, Milton Keynes, MK1 1DQ, England

Tel: (01908) 375411

Fax: (01908) 376118

Web Site - http://www.marshallamps.com

Whilst the information contained herein is correct at the time of publication,

due to our policy of constant improvement and development, Marshall

Amplification plc reserve the right to alter specifications without prior notice.

Nov ‘98

Introduction

The relationship between the guitarist and amplifier has been our prime concern since the earliest

Marshall’s were produced. We always aim to give that extra edge, which can help to inspire the player,

fuelling creativity and the ability to express.

Advances in technology have allowed us to modify and enhance this basic principle for the benefit of the

musician. However, we have never lost sight of that extra emotional drive that only valves are capable of

producing. The whole character of our unique sound emanates from the breathing full bodied pure tone of

the valve.

Your JMP-1 MIDI pre-amp is a carefully designed coalescence between modern MIDI technology and

classic Marshall valve circuitry. It’s many tones are all valve generated and presented in a way that is both

comfortable and familiar to guitar players.

The digital control capabilities add a new degree of flexibility to the way in which the tones can be switched

and processed. The advantages provided by this level of control are truly astounding. After studying the

manual and with a little practical exploration, you will find an unbelievable range of sounds and will very soon

wonder how you managed without MIDI. The only limit is your own imagination.

JMP-1 Front Panel Features

1. Input Socket Connect the guitar to this socket.

2. Headphone Socket For the connection of stereo headphones.

Headphones with an impedance of 600 Ohms will give

the best performance. Connecting headphones does not

disable the outputs of the pre-amp.

3. Output Level Control Controls the volume level from the master left and right

outputs (Item 25).

4. Display The display is split into two sections and shows patch

and data information.

5. Patch Key Push this key to enter patch selection mode (0-99). The

patch key LED will illuminate to indicate patch mode.

6. Store Key Use this key to store a patch in the memory.

Operational Note:

Push once and the store key LED will flash. The data entry control (7) can now be used to change the storage location.

Pushing patch or a parameter key will abandon the store. Push the store key again to complete the store. (Also see

section Creating Your Sounds).

7. Data Entry Control This rotary control is used to increment/decrement data

information, or to select a patch in patch mode.

8. Volume Key Push this key to adjust the patch volume level between 0

and 20. The volume key LED will illuminate to indicate

that the volume parameter has been selected. The data

display will show the current value. The value can then

be adjusted using the rotary data entry control (7).

9. Gain Key Push this key to adjust the level of gain between 0 - 20.

10-13. Tone Control Keys These keys should be combined to shape the Bass,

Middle, Treble, and Presence tone parameters. They can

all be adjusted between -6 and +6.

14. Effect Key This key varies the mix of the stereo effects loop between

0 and 12. At 0 only the direct signal is heard and at 12

only the effected signal is heard. When at 12 the loop is

effectively running in series i.e. no direct signal. This is

ideal for use with a graphic equalizer or compressor

limiter. As the effect parameter level is reduced, more

direct signal is introduced as with a parallel loop. This is

best suited to Chorus, Delay, Reverb etc.

15. OD1 Key This key selects overdrive 1, a warm vintage drive

reminiscent of Marshall Super Lead amps through to

modern day Master Volumes.

16. OD2 Key Selects overdrive 2. This a tightly focused high gain

drive which can be smooth or aggressive depending on

the E.Q. and gain settings.

17. Bass Shift This is a subtle low frequency character control which

can be switched in or out of any sound selection.

18. Clean 1 Key Selects Clean 1, which has a full warm character and

pure vintage tone.

19. Clean 2 Key Selects Clean 2. This has a bright sparkling tone ideal for

clean picking and ringing chords.

20. MIDI-Mapping Key The mapping function enables the mapping of incoming

MIDI patch messages to internal patches and outgoing

MIDI patch numbers to external devices. (See MIDI

mapping).

21. MIDI Channel Key This key selects the MIDI Channel on which the JMP-1

transmits and receives MIDI information.

22. Power Switch On/Off switch for mains power.

Rear Panel Features

23. Emulated Outputs Left and right outputs featuring Marshall speaker

emulation. The volume level from these outputs is

controlled by the volume level parameter key (8) not by

the output level control (3).

Operational Note: Stereo Speaker Emulation.

The Marshall speaker emulation circuit is a special filter which gives a signal virtually identical in sound to a speaker

cabinet. This allows you to link directly to the PA and obtain a stunning direct sound in a live situation. In the studio it

will give a true guitar tone direct to tape.

24. Emulated Level Selection Switch

Selection switch providing +4dB or -10dB output

levels on the speaker emulated outputs.

25. Master Outputs

Left and right outputs for connection to a power amplifier.

26. Master Level Selection Switch Gives +4dB or -10dB Master output level options.

27. Effects Return Jacks Left and right jack sockets for connection from the outputs

of an external effects processor. If using a mono effects

processor the left hand return socket only should be used.

In this instance both the left and right master outputs and

speaker emulated outputs will now be working in mono.

28. Effects Level Selection Switch Provides level selection of +4dB or -10dB to match the

level of external effects processors.

29. Effects Send Jack Output for connection to the input of the external effects

processor.

30. Footswitch Socket Connection point for optional Marshall four way

footswitch to give 4 patch selection.

31. MIDI OUT Sends outgoing MIDI messages from the JMP-1.

32. MIDI THRU Sends out MIDI messages identical to those coming in

through the MIDI IN terminal.

33. MIDI IN Terminal to receive incoming MIDI messages from

external MIDI device.

When you switch on

When switching on the JMP-1, the unit will run through an initialising

process and will then default to the patch number that was selected when

the JMP-1 was last switched off (Fig1). Your JMP-1 is now ready for

action.

Creating Your Sounds

Your JMP-1 is capable of producing a vast array of different tones, stored in the 100 available patches.

The simplicity of creating and storing these sounds is a major advantage and feature of the pre-amp.

A “Patch” is a combination of all the programmable elements that you put in, therefore if all tone and

volume selections are at 0, no sound will be produced. Each patch is made up of:

(A) The channel selection i.e. OD1, OD2, Clean 1, Clean 2 & Bass Shift

(B) The individual volume, gain, tone and effects levels that you have selected.

The first step is to select a patch by pressing the patch key (5) using the rotary data control (7) to reach the

desired patch number. The next stage is to “build” your required sound, firstly by selecting the channel

OD1, OD2, Clean 1 or Clean 2 with or without bass shift, then by selecting the volume, gain, tone and

effects levels. These controls work in exactly the same way as a normal Marshall amplifier, where

increasing the gain brings in more overdrive and the tone selections interact to “shape” the sound.

The JMP-1’s controls are there to be used to the full and by experimenting with all the extremes you will

quickly understand it’s capabilities and build your own library of sounds.

Patch Data

Patch

Store

Fig 1 Patch

Storing Yours Sounds

When you are satisfied with the sound that you have created, storage is

achieved in the following way. Push the store key (6) once , the LED will

flash (Fig 2). Select the desired patch location using the data entry

control (7). (Pressing the patch or any parameter key will abandon the

store). Push store a second time to complete the store

Memory Lock

A memory lock can be set to keep your data safe. This will disable any

functions that write data to the internal memory i.e Store, Mapping,

Channel & System Exclusive. If the memory is locked an 'L' will appear in

the right of the display when you attempt a store (Fig 3). At this stage the

lock can be toggled on or off by pressing the Channel key.

Sound Selections

There is a definite identifiable character to the “Marshall Sound” throughout the years. largely derived

from the unique qualities of valve power. Our expertise in harnessing valve drive has been fully exploited

in the JMP-1 to recreate the various classic sounds and to generate new tones that will become the classics

of the future. Bearing in mind the variations in guitar types and styles, plus the flexibility of the control

parameters, the following guide gives an indication of each channel's basic sound type.

Clean 1

This is a warm full bodied clean tone, ideal for rich chords, which can be softened for jazz tones or, by

adding gain, will suit clean lead lines with a hint of vintage distortion.

Clean 2

In complete contrast to Clean 1, Clean 2 is bright and glassy with a clear jangling tone. In addition it

contains the unique lively “edge” found only in the early JTM 45 and Super Lead Amps operating at

volumes just below distortion.

OD1

Features the purity of distortion from the golden age of the plexi glass Super Leads. As the gain is

increased you pass through degrees of distortion into a rich higher gain mode, with just the right nuances

for the modern blues rock player. Vintage crunch, modern metal and fat blues lead sounds are all readily

available.

OD2

Tightly focused stunning high gain is what you will find in OD2. Modern and aggressive, smooth and

fluid, the gain levels and singing tone of this channel will give you infinite sustain whilst retaining a pure

toneful quality.

Bass Shift

The Bass Shift option can be switched in or out of any channel selection. When selected it thickens the

bottom end of the sound and tightens the playing feel. On clean selections it adds body and on overdrive

provides the extra low end “throb” so essential for heavy rock sounds.

Patch Data

Patch

Store

Patch Data

Patch

Store

Fig 2 Store

Fig 3 Memory lock Activated

Factory Sounds

Your JMP-1 has 26 sounds ready programmed into patches 00-25. These patches have been programmed

by experienced guitarists. They have also been used in full stage and studio performance. These sounds

can all be edited in the way described earlier and recalled if necessary using the procedure described in

the section-“to re-initialise the JMP-1.”

Pre set sounds

TITLE MODE B/S VOL GAIN BASS MID TREB PRES

00 Smoke-em OD 2 off 18 20 3 -3 3 1

01 Chunkus OD 1 off 17 20 1 -3 3 4

02 Sticky OD 1 on 15 13 1 2 6 3

03 Cleeeeen CL 2 off 20 9 3 -1 4 6

04 British Steel OD 2 on 17 16 4 0 4 1

05 Nasal Tone OD 2 on 16 20 0 1 6 6

06 Quo !!! OD 2 on 17 10 2 -2 6 3

07 Angus-Ho OD 2 on 17 14 0 -1 3 2

08 Filth OD 2 on 17 20 2 -6 6 6

09 Bloooz-O OD 2 on 17 11 2 -2 3 2

10 Bloooz-O+ OD 2 on 17 19 2 -2 3 2

11 Tej'as OD 1 on 16 14 1 -1 4 1

12 Modster OD 1 on 14 20 2 1 5 5

13 Biffa OD 1 off 15 20 2 0 3 3

14 More Gary OD 2 on 17 4 3 0 3 3

15 Mid-lands OD 1 on 14 17 2 6 3 3

16 Sunshine OD 2 on 15 10 1 6 -6 3

17 Britaevious CL 2 on 17 17 4 -2 6 6

18 Trash OD 1 on 17 9 4 -1 2 3

19 800's OD 1 off 16 15 6 0 3 3

20 LA Crunch OD 1 on 16 17 6 1 3 2

21 Crusher OD 1 on 18 12 5 -4 5 4

22 Grit Clean CL 2 off 16 19 3 -1 4 6

23 Shred Spread OD 1 on 17 20 5 0 6 6

24 Warm Grit CL 1 on 16 20 -1 3 6 6

25 Mellow CL 1 off 20 14 2 -2 1 1

Pre set sounds descriptions

TITLE MODE ATTRIBUTES PICKUPS COMMENTS

00 Smoke-em OD 2 Lots of drive & sustain It starts here

01 Chunkus OD 1 Big, Ugly & Fat Gain controls "chunkiness"

02 Sticky OD 1 Edgy grime Big change for different guitars

03 Cleeeeen CL 2 Very Lots of headroom

04 British Steel OD 2 Warm & Heavy English overdrive

05 Nasal Tone OD 2 Thin, midrangy & cutting When tracks are full, this fits

06 Quo !!! OD 2 Bright crunch Rocks you all over the world

07 Angus-Ho OD 2 Mid '70s Marshall Tone

08 Filth OD 2 Bright, semi scooped Great for chords

09 Bloooz-O OD 2 Plexi 50 Watt Classic tone

10 Bloooz-O+ OD 2 Plexi 100 Watt As above, more aggressive

11 Tej'as OD 1 Punchy/dark drive Increase gain for vintage singles

12 Modster OD 1 Mod-ed Plexi More than enough

13 Biffa OD 1 Obnoxious overdrive In your face crunch

14 More Gary OD 2 JTM 45 on "6" Started it all

15 Mid-lands OD 1 Honky mid range voice Cuts through

16 Sunshine OD 2 Cleaner than you think! Increase Treb. for dark guitars

17 Britaevious CL 2 Modern clean - Pick's up EFX well Hi output pickups will distort

18 Trash OD 1 Very broad modern tone Fills up a lot of space

19 800's OD 1 JCM800 - Deliverin' the dB's Set bass to suit your guitar

20 LA Crunch OD 1 Mod-ed JCM800 on "5" Decrease Pres. for single coils

21 Crusher OD 1 JCM900 on "8" Mid control very effective

22 Grit Clean CL 2 Clean & on the edge Hi output pickups will distort

23 Shred Spread OD 1 Full scoop shred tone Bass control is the key here

24 Warm Grit CL 1 Dark & on the edge Hi output pickups will distort

25 Mellow CL 1 Clean & pretty Roll back guitar tone for full "Jazz"

Some Notes On MIDI

In a modern guitar set-up you might have a number of elements, a pre-amp and an effects processor or

two. By using MIDI to link these devices together, you can control them all simultaneously. This is the real

use of MIDI for the guitarist (Musical Instrument Digital Interface). Most MIDI devices are equipped with

three MIDI terminals, MIDI IN, MIDI THRU and MIDI OUT. The connection between these terminals is quite

simple. A MIDI IN terminal would be connected to a MIDI Out or MIDI THRU terminal. Messages are sent

from a MIDI OUT terminal to a MIDI IN terminal.

MIDI messages received at the MIDI IN terminal are simultaneously routed through at the MIDI THRU

terminal. So the messages being sent via MIDI THRU are a direct copy of the messages received at

MIDI IN. The MIDI OUT terminal is not the same as the MIDI THRU terminal. The JMP-1 will send it’s own

MIDI messages via the MIDI OUT terminal.

There are various different MIDI messages that one device can send to another. The most important

message is the MIDI program (patch) change message. When the JMP-1 receives a program change

message it will call up a patch. Whenever the JMP-1 calls up a new patch it also sends a MIDI program

change message via the MIDI OUT terminal. Pressing a pedal on a MIDI foot controller will send a

MIDI program change message. Each MIDI program change message carries a number between 00 and

127 corresponding to the patch/program to be called up. The JMP-1 has 100 internal patches but will

respond to all 128 MIDI program change messages, by using a MIDI mapping table.

MIDI Channel

Another important thing to know about MIDI, is the idea of MIDI Channels. Most MIDI messages are sent

over a MIDI Channel, of which there are 16. In order for one MIDI device to communicate with another,

both devices must be operating on the same MIDI Channel.

The JMP-1 can be set to operate on any one of the 16 MIDI channels or in Omni mode. In Omni mode the

JMP-1 will respond to MIDI messages on all channels and will transmit on channel 1.

To Set The MIDI Channel: After pressing the channel key the display will indicate the current MIDI Channel

setting (Fig 4).

Use the data entry control to select channels 1 to 16 or Omni

mode. Press the channel key again to store the channel setting

and return to patch mode.

Note: The MIDI Channel setting is a ‘Global` parameter and not

stored with an individual patch. MIDI Channel setting is retained

whilst the unit is not powered.

Fig 4 Channel selection

Patch Data

Patch

Store

MIDI Mapping

MIDI mapping is a simple and very useful facility, but it often confuses those who are new to MIDI. The MIDI

Mapping table is stored in the memory and is made up of two parts, Input mapping and Output mapping.

Input Mapping

The input mapping table makes it possible to transpose any incoming MIDI Program Change number to

select any desired JMP-1 patch. For Example:

MIDI Program Change 124 could be mapped to JMP-1 patch 36, so whenever the JMP-1 received MIDI

Program Change 124 it would call up patch 36. The Input mapping function is invaluable if you are using

a MIDI foot controller that sends fixed Program Change messages.

Output Mapping

In the same nature as input mapping, the output mapping function can transpose any outgoing Program

Change message. If the MIDI OUT of the JMP-1 is driving an external effects processor, the JMP-1’s output

mapping can be used to select a particular effects program for each JMP-1 patch, with the advantage that

several JMP-1 patches can share the same program on the effects processor.

To Edit The Mapping Table:

1) Push Map key once to select incoming MIDI Program number. (See Fig 5). Use the data entry control to

select the incoming Program number (00 to 127). The decimal point signifies program numbers 100 and over.

2) Push again to select the Internal Patch to be called up (00 to 99) (See Fig 6).

3) Push the Map key a third time to set the outgoing MIDI Program Change message to (00 to 127) (See Fig 7).

4) Pushing the Map key a fourth time will store edits and return the JMP-1 to Patch mode.

Note: The mapping table is remembered whilst the JMP-1 is not powered.

Fig 7. Outgoing MIDI programFig 5. Input Mapping Fig 6. Internal Patch Number

Patch Data

Patch

Store

Patch Data

Patch

Store

Patch Data

Patch

Store

Indicates 100-127

Incoming MIDI

Data

4 Way Footswitch

(Patches 1-4)

Call up Internal

Patch (00-99)

Front Panel

Control

Output Mapping

to MIDI Device 00-127

MIDI

IN MIDI

THRU MIDI

OUT

Input

Mapping

Four Way Footswitch

The optional Marshall four way footswitch (model MPM 4E) provides a simple means of selecting four patches.

The footswitch will call up patches one to four, however, the Mapping facility can be used to call up any

four of the 100 JMP-1 patches.

To Re-initialise The JMP-1

This procedure will re-load the factory sounds and reset the mapping table.

WARNING:-

Your edited sounds will be lost if the unit is re-initialised.

Procedure, Hold down OD1 and Clean 1 whilst switching on the power.

Memory back-up

The JMP-1 has an internal battery back-up system to keep your patches safe

while the unit is switched off. This battery should last for several years.

Every time you power up the JMP-1, a self check program is run. If any

errors are detected an "E" will be displayed momentarily (Fig 8).

If this should occur repeatedly, then it is likely that the internal back-up

battery needs replacing. Contact your dealer as soon as possible and

back up your patches (see System Exclusive).

System Exclusive

By using system exclusive MIDI code, it is possible to dump all your patch and mapping settings to an

external MIDI device such as a sequencer or data filer.

To Transmit MIDI Dump Data:-

Connect a MIDI cable from the MIDI OUT of the JMP-1 to the MIDI IN of the receiving device. Press the

PATCH key and the VOLUME key together to begin transmitting. The display will indicate that a MIDI

exclusive dump is in progress by counting the data blocks (0 thru' 9) as they are transmitted (Fig 9).

When the transmission is completed, the display will return to normal.

To Receive a System Exclusive Dump:-

Connect a MIDI cable from the MIDI OUT of the transmitting device to the MIDI IN on the JMP-1. (Ensure

that the memory lock is off - see page 6)

WARNING:- Receiving a MIDI dump will re-write all your patches and mapping data, so be sure that you are

loading the correct data before you start. If you are unsure then make a back up of your current data

beforehand.

ecute the dump from the transmitting device. When the JMP-1

recognises the system exclusive code it will automatically respond by

counting the MIDI data blocks as they are successfully received (Fig 9).

If this does not happen then re-check the MIDI connections and that you

are sending the correct file. When the transmission is completed, the

display will return to normal.

Fig 9. System Exclusive Dump

Patch Data

Patch

Store

Patch Data

Patch

Store

Fig 8. Error Detected

Andere Handbücher für JMP-1

Inhaltsverzeichnis

Andere Marshall Amplification Verstärker Handbücher

Marshall Amplification

Marshall Amplification DSL20CR Bedienungsanleitung

Marshall Amplification

Marshall Amplification 1959SLP Bedienungsanleitung

Marshall Amplification

Marshall Amplification MG30DFX Bedienungsanleitung

Marshall Amplification

Marshall Amplification Valvestate Pro Bedienungsanleitung

Marshall Amplification

Marshall Amplification JCM800 2203-01 Bedienungsanleitung

Marshall Amplification

Marshall Amplification JVM410C Bedienungsanleitung

Marshall Amplification

Marshall Amplification EL84 20/20 Bedienungsanleitung

Marshall Amplification

Marshall Amplification MG10CD Bedienungsanleitung

Marshall Amplification

Marshall Amplification MG15HCFX Bedienungsanleitung

Marshall Amplification

Marshall Amplification Transistor Split Channel Bedienungsanleitung

Marshall Amplification

Marshall Amplification Extension Cabinet Bedienungsanleitung

Marshall Amplification

Marshall Amplification JTM45 Bedienungsanleitung

Marshall Amplification

Marshall Amplification JCM 800 Bedienungsanleitung

Marshall Amplification

Marshall Amplification MG GOLD SERIES Bedienungsanleitung

Marshall Amplification

Marshall Amplification MINI JUBILEE 2525H Bedienungsanleitung

Marshall Amplification

Marshall Amplification 1922 Bedienungsanleitung

Marshall Amplification

Marshall Amplification MG10KK SERIES Bedienungsanleitung

Marshall Amplification

Marshall Amplification ORIGIN 20 Bedienungsanleitung

Marshall Amplification

Marshall Amplification EL84 20/20 Bedienungsanleitung

Marshall Amplification

Marshall Amplification Acoustic Soloist AS50D Bedienungsanleitung

Marshall Amplification

Marshall Amplification MG250DFX Bedienungsanleitung

Marshall Amplification

Marshall Amplification DSL 15H Bedienungsanleitung

Marshall Amplification

Marshall Amplification JCM800 Bedienungsanleitung

Marshall Amplification

Marshall Amplification JCM900 4100 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung