Mercia Garden Products 03HEL1010DDFW-V2 Gebrauchsanweisung

03HEL0808DDFW-V1

N/A

Overlap

Cladding

Shiplap

Cladding

Solid Sheet

Roof

T&G Roof

Solid Sheet

Floor

T&G Floor

Fixed

Windows

Opening

Windows

8x8 Helios Summerhouse

For Assistance Please

Contact Customer Care on

01636 880514

2mm Drill bit

Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All building’s should be erected by two

adults

For ease of assembly, it is advisable to

pilot drill all screw holes and ensure

all screw heads are countersunk.

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand

(not supplied) including a Phillips screwdriver, Stanley knife, wood saw,

step ladder and drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather

conditions. For the duration of heavy or extended periods of rain, swelling of the

wood panels may occur. Warping of the wood may also occur during excessive

dry spells due to an interior moisture loss. Unfortunately, these processes cannot

be avoided but can be helped. It is suggested that the outdoor building is

sprayed with water during extended periods of warm sunshine and sheltered as

much as possible during rain or snow.

Our buildings are pre treated with a water based treatment**; this only helps to

protect the product during transit and for upto 3 months against mould. To

validate your guarantee and ensure longevity of the product, it is ESSENTIAL the

building is treated with a wood preserver within the rst three months of

assembly and thereafter in accordance with the manufactures recommenda-

tions. Care must be taken to ensure the product is placed on a suitable base.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Whilst all products manufactured are made to the

highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot

accept responsibility for your safety whilst erecting or

using this product.

Mercia Garden Products Limited, Sutton On Trent, Newark, Nottinghamshire, NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces

of the timber. You are strongly advised

to wear gloves when working with or

handling rough sawn timer.

**Protim Fentex E5**

Biocidal Product Regulation (EU 528/2012) Article 58 Information

Protim Fentex E2 preserved wood is a “treated article”which incorporates biocidal products.

Wood correctly preserved with Protim Fentex E2 is protected against mould in storage.

Contains: IPBC (3-iodo-2-propynyl-N-butyl carbamate) and propiconazole.

Wear gloves when handling freshly treated wood.

Avoid breathing dust when cutting treated or untreated wood.

Dispose of o-cuts responsibly – do not burn.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer

to diagrams for the base dimensions, The base should be slightly smaller than

the external measurement of the building, i.e. The cladding should overlap the

base, creating a run o for water. It is also recommended that the oor be at

least 25mm above the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Please retain product label and instructions for future reference

P 1

General Instructions

03HEL1008DDFW-V2

10x8 Helios Summerhouse

03HEL1010DDFW-V2

10x10 Helios Summerhouse

Refer to the instructions pages for you specic product code

P 2

03HEL1010DDFW-V2

Overall Dimensions:

Length = 3040mm

Width = 3500mm

Height = 2195mm

Base Dimensions:

Length = 2916mm

Width = 3102mm

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

123 4 5 6

910 11 12 13 14

Roof Block - 140mm

Qty 8

3635

2x Front Fascia 1520mm

Door Panel Window

Panel L

Window

Panel R

Window

Gable R

Window

Gable L

Front Roof

Back Roof

Left

Back Roof

Right

Front

Floor

Back

Floor

QTY 2

Slave

Door

Master

Door

4x Bottom Roof Trim 1705mm

16 4x Top Roof Trim 1750mm

17 2x Cover Trim 1792mm

18 2x Cover Trim 2106mm 19 Floor Blocks 400mm QTY 11 20 Roof Support 2828mm QTY 4

21 2x Corner Trim 2059mm 22 2x Roof End 964mm 23 2x Roof End 2536mm

24 Door Bar 1705mm 25 2x Posts 2044mm 26 2x Door Beading 1711mm

Finial

Turn Button

QTY 2

Flush Hinge

QTY 6

Key Plate

2928

Door Handle

QTY 2

Mortice Lock

Barrel Bolt

QTY 2

x4 Rain Guard 580mm

Plain Side

QTY 2

Felt

50mm Screw x57

40mm Screw x105

Felt Tacks x185

30mm Screw x133

60mm Screw x80

30mm Black Screw x2

Nail Bag

Pre Assembly

Remove the transportation blocks

from the bottom of each panel

before beginning assembly.

Step 1

Position oor sections onto a rm

and level base, x with 8x50mm

screws alternate the xing posi-

tions along the length of the oors.

Fix the front oor Panel to the 2

existing panels using the oor

joining bocks. Use 2x50mm screws

per block screwing through the

boards into the top of the block,

connecting the oor pieces.

30x50mm Screws

50mm

screw

Pre drill

hole

*Ensure your base has suitable drainage and is

free from areas where standing water can collect.

80mm Screw x14

Rain Guard 1472mm

P 3

Please retain product label and instructions for future reference

Step 2

Attach the ush hinges to both

the master & slave doors using

3x30mm screws per hinge.

*Fix to the doors via the outer

plate.

Fix the doors into the door panel

aperture, securing into place

using 3x30mm screws per hinge.

*Fix to the door panel via the

inner plate.

36x30mm Screws

30mm

screw

Pre drill

hole

Fit the mortice lock into the

recess on the master door &

x into place using with the

screws provided. Attach the

key plate to the slave door,

once again using the screws

provided.

Fix the door handles and the

metal bar (spindle) using

8x30mm screws.

*Ensure the mortice lock opens

and closes freely. If not remove

the lock and turn the catch

around using the small grub

screw.

8x30mm Screws

30mm

screw

Pre drill

hole

Step 2 Continued...

Fix the door bar to the inside

of the slave door with 6x30mm

screws, as shown in the

illustration.

Attach the door beading strips

to the inside of the door frame

(either side of each door) with

8x30mm screws, making sure

the beading strips sit ush with

the framing.

14x30mm Screws

Attach the tower bolts to

the door bar using the

screws provided.

*Ensure the bolts locate into

the keeps and the door locks

in place properly.

30mm

screw

Pre drill

hole

Rain Guard 1472mm

The Mortice Lock is Reversible

50mm

screw

Pre drill

hole

60mm

screw

60mm

screw

Pre drill

hole

60mm

screw

Pre drill

hole

60mm

screw

Pre drill

hole

P 4

Please retain product label and instructions for future reference

Step 3

Place the plain sides and the rst

gable section onto the oor.

connect the 2 plain sides using

3x50mm screws and secure the

gable at the corner using 3x60mm

screws.

Do NOT secure to the oor until

the roof has been tted.

3x50mm Screws

3x60mm Screws

Step 4

Fix the second gable to

the plain side at the

corner using 3x60mm

screws.

*Do NOT secure to the oor until

the roof has been tted.

Attach the posts to the

front of each gable with

3x60mm screws per post.

9x60mm Screws

Step 5

Secure the left & right

window panels to the

posts using 3x60mm

screws per panel.

Do NOT secure the

assembly to the oor

until the roof is tted.

6x60mm Screws

Step 6

Place the assemble door

panel inbetween the left

and right window panels,

xing into place using

6x60mm screws.

Do NOT secure the

assembly to the oor

until the roof is tted.

6x60mm Screws

P 5

Please retain product label and instructions for future reference

Step 8

Rest the rst roof panel on top of the

supports and secure with 20x40mm

screws as shown in the illustration.

*Ensure to align the screws with each

roof support bar.

Fix the roof (internally) to the roof

support bar using 8x40mm screws

(making sure the roof framing sits

behind the support bar) .

Repeat this process with the second

roof panel, ensuring there is an equal

amount of overhang either side of the

building.

56x40mm Screws

40mm

screw

Pre drill

hole

Step 9

Place the front roof onto the assembly

securing into place using 4x40mm

screws as shown in the illustration.

Following the same method outlined in

step 8 x the front roof (internally) to the

roof support bar using 4x40mm screws.

8x40mm Screws

40mm

screw

Pre drill

hole

40mm

screw

Pre drill

hole

80mm

screw

Step 6

Place the first ridge bar

inside the building and

line up with the upright

framing on each gable.

Align the back edge of the

ridge bar with the top of the

gable. Once in place mark

the position on both sides

with a pencil.

Place the roof support block

to the pencil mark and

secure in place using

2x40mm screws per block.

*Repeat this process on both sides

with the remaining roof support

bars.

Place the ridge bar(s) on top

of the attached blocks and

secure through the outside

of both gables using

2x80mm screws per side.

14x40mm Screws

14x80mm Screws

*Hint: When tting the roof bar pencil mark the centre

of the roof support bar and follow down onto the gable

at a right angle, this will give you a guide to x the

support bars in place.

60mm

screw

Pre drill

hole

Felt

tacks

*Felt size: 3140mm

P 6

Please retain product label and instructions for future reference

Step 10

Position the large and small

roof ends onto the roof.

*Ensure the tongue & groove

meet and the boards sit ush

with the roof framing.

Fix the boards in place using

12x40mm screws, making sure

to screw through the roof and

gable framing.

12x40mm Screws

40mm

screw

Pre drill

hole

Please retain product label and instructions for future reference

Step 11

Now the roof has been tted

secure the building to the

oor with 36x60mm screws

*Ensure to align the screws with the

oor bearers.

36x60mm Screws

Step 12

Cut the felt into 4x strips.

Roll the felt across the roof in the order

shown in the illustration, leaving

approximatley 50mm of overhang at

the front & rear as well as an equal

amount either side of the building.

*Each sheet needs approximately 50mm

of overlap except the last sheet which

requires 250mm overlap.

165x Felt Tacks

HANDLE

WITH CARE

30mm

screw

Pre drill

hole

30mm

screw

Pre drill

hole

Step 13

To secure the roof felt in place,

sandwich the felt between the

top and bottom roof trims as

shown in the illustration, xing

into place using 24x30mm

screws.

24x30mm Screws

30mm

screw

Pre drill

hole

Step 14

Fix the fascias to the front of the building

securing each board to the roof framing

using 8x40mm screws.

Place the nial over the fascia joint and

x into place with 2x40mm screws.

10x40mm Screws

40mm

screw

Pre drill

hole

Slave Door

Locking Door

Please retain product label and instructions for future reference

Step 15

Fix the cover trims around the

building across the joints on

each panel and at the corners

using 3x30mm screws per trim.

21x30mm Screws

Step 16

Attach the turn buttons to the top

& bottom of the slave door using

2x30mm black screws.

*These turn buttons help to keep

your doors straight during high

and low levels of moisture

content in the air.

2x30mm Black Screws

50mm

screw

Pre drill

hole

It is ESSENTIAL that you apply wood

treatment immediately after the building

has been assembled.

AFTER TREATMENT:

score around protective

cover on glazing and

carefuly peel

covering back

50mm

screw

Pre drill

hole

SILICONE

SEALANT

Step 17

Attach the rain guards centrally

above each window using

3x50mm screws per guard.

18x50mm Screws

Please retain product label and instructions for future reference

Step 18

Secure the larger rain guard

above the doors, xing into

place using 4x50mm screws.

*ensure to screw into the

framing above door.

4x50mm Screws

SILICONE

SEALANT

*Hint: Silicone seal the back of each

rain guard to help reduce water

running behind.

*Hint: Silicone seal the back of the

rain guard to help reduce water

running behind.

Inhaltsverzeichnis

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 01PTOSBRA1008SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634CSNE0404HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 06LOG002-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products Groundsman Dutch Barn 8x8 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03VER0808-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1208DDOP-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1406DDOP-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 02DTTWRS0605-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0406DDNW-V Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03PTMBPN0406BR-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHRA0808FGC42TW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0806DDFW-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 06LOG015-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVRA0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVRA0806SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVRA0604SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OVLPP0705SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OVLPA0304SDNW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OSBA0705SDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03PTODB0406-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OSBA0707DDSW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products OSB APEX Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0644CSNE0404HGDD2SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 04LEAN0804-V1 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung