Mercia Garden Products 03PTMBPN0406BR-V1 Gebrauchsanweisung

ANTI-ROT

GUARANTEE TODAY

PLEASE SCAN HERE:

Measure

under the

head

Measure

overall

length

Screws & Nails Bolts To identify the

xings required

for each step use a

measuring tape.

03PTMBPN0406BR-V1

PRESSURE TREATED MATCHBOARD PENT 4X6 BAR

2mm Drill bit

x2 Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All buildings should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,

annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing

damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-

ment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above

the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

For ease of assembly, you

will need a tape measure to

check dimensions of

components.

Pressure Treated Timber

Your building has been pressure treated.

Pressure treating is a chemical process which helps to protect wood against adverse weather which could

lead to rot or insect damage.

The most common chemicals used to pressure treat wood are Alkaline Copper Quaternary (ACQ),

Copper Azole (CA), and Micronized Copper Quaternary (MCQ).

Safety: Always wear gloves, eye protection and a dust mask when handling wood. Due to chemicals in

pressure treated wood, never burn its sawdust or scraps; instead dispose in a landll.

P 1

Please retain product label and instructions for future reference

General Instructions

6 7

911

50mm Screw x 35

40mm Screw x 27

70mm Screw x 71

30mm Screw x 8

P 2

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,

annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing

damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-

ment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above

the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

Back Panel QTY 2

AI-S22MBVCPP837X1762-V1

Left Plain Panel QTY 1

AI-S22MBVCPP1119X900-V1

Left Gable QTY 1

AI-S21MBPGTL1119X393-V1

Right Gable QTY 1

AI-S21MBPGTR1119X393-V1

Roof QTY 2

AI-S22FEPR971X1428-V1

Front Panel QTY 2

AI-S22MBVCPP837X900-V1

Right Plain Panel QTY 1

AI-S22MBVCPP557X900-V1

Top Panel QTY 2

AI-S21MBVCPP837X352-V1

Right Bar Top QTY 1

AI-03S21MBSHFCO632X254-V1

Plain Bar Top QTY 2

AI-03S21MBSHF658X254-V1

Left Bar Top QTY 1

AI-03S21MBSHFCO254X1194-V1

Ridge Bar 27x70x1674mm QTY 1

F2770-1674mm

Front Cover Trim 12x56x1848mm QTY 1

S1256-1848mm

Side Cover Trim 12x56x1269mm QTY 2

S1256-1269mm

Roof Cover Trim 12x80x1130mm QTY 1

S1280-1130mm

Fascias 12x95x1428mm QTY 2

S1295-1428mm

Side Fascia 12x95x1966mm QTY 2

S1295-1966mm

Bar Support 27x44x258mm QTY 2

F2744-G-298mm

Front Post 75x75x2100mm QTY 2

PI-14-0306

Back Post 75x75x1800mm QTY 2

PI-14-0304

Corner Brace QTY 2

PI-07-0012

03PTMBPN0406BR-V1

Overall Dimensions:

Width = 1966mm

Depth = 1432mm

Height = 2140mm

Base Dimensions:

Width = 1824mm

Depth = 1269mm

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Nail Bag

There may be extra screws present in the nail bag

50mm Screw x 12

40mm Screw x 11

70mm Screw x 21

P 3

Please retain product label and instructions for future reference

Bar Support 27x44x258mm QTY 1

F2744-G-298mm

Roof Cover Trim 12x80x1130mm QTY 1

S1280-1130mm

Front Panel QTY 1

AI-S22MBVCPP837X900-V1

Back Panel QTY 1

AI-S22MBVCPP837X1762-V1

Roof Panel Extension QTY 1

AI-S22FEPR837X1428-V1

Cover Trim Extension 12x56x837mm QTY 1

S1256-837mm

Fascia Extension 12x95x837mm QTY 2

S1295-837mm

Plain Bar Top Extension QTY 1

AI-03S21MBSHF837X254-V1

Top Panel QTY 1

AI-S12MBVCPP837x352-V1

Ridge Bar 27x70x2511mm QTY 1

F2770-2511mm

Overall Dimensions:

Width = 2803mm

Depth = 1432mm

Height = 2140mm

Base Dimensions:

Width = 2661mm

Depth = 1269mm

Extension Pack

03PTMBPN0403BRPB-V1

Nail Bag

There may be extra screws present in the nail bag

If Extension Pack has been purchased, please follow

steps labelled ‘Extension Pack’ where present

P 4

Please retain product label and instructions for future reference

Stand the Back Panels (No. 1) upright as

shown, with the larger gap between the panel

framing at the bottom, as per the

measurements on the diagram. Fix together in

an alternating pattern using 4x70mm screws

Place Corner Posts 75x75-1800mm (No. 19) to

either side ush with the inside of the panel.

Attach the post (No.19) to the back panel

(No.1) using 4x70mm screws per post, xing

through the panel into the post.

12x70mm Screws

Step 1

Parts Needed- No.1 QTY 2

- No. 19 QTY 2

Pre drill

hole

70mm

screw

Ariel View

Stand the Back Panels (No. 1)

upright as shown, with the larger

gap between the panel framing at

the bottom, as per the

measurements on the diagram. Fix

together in an alternating pattern

using 4x70mm screws per join.

Place Corner Posts 75x75-1800mm

(No. 19) to either side ush with

the inside of the panel.

Attach the post (No.19) to the

back panel (No.1) using 4x70mm

screws per post, xing through

the panel into the post.

16x70mm Screws

Step 1A

Parts Needed- No.1 QTY 3

- No. 19 QTY 2

Pre drill

hole

70mm

screw

Extension Pack

Ariel View

767mm

868mm

767mm

868mm

19 19 19

111

P 5

Please retain product label and instructions for future reference

Stand the Front Panels (No.6) upright as

shown. Fix together using 4x70mm

screws in an alternating pattern.

Place the Corner Posts 75x75 - 2100mm

(No.18) at either side ush with the

outside of the panels.

Attach the Corner Posts (No.18) to the

Front Panels (No.6) using 4x70mm

screws per post, xing through the

panel into the post.

12x70mm Screws

Ariel View

Pre drill

hole

70mm

screw

Step 2

Parts Needed- No.6 QTY 2

- No. 18 QTY 2

Stand the Front Panels (No.6) upright as

shown. Fix together using 4x70mm

screws in an alternating pattern.

Place the Corner Posts 75x75 - 2100mm

(No.18) at either side ush with the

outside of the panels.

Attach the Front Posts (No.18) to the

Front Panels (No.6) using 4x70mm

screws per post, xing through the

panel into the post.

16x70mm Screws

Pre drill

hole

70mm

screw

Step 2A

Parts Needed- No.6 QTY 2

- No. 18 QTY 2

Extension Pack

Ariel View

18 618 6

18 18 18 18

666

P 6

Please retain product label and instructions for future reference

Step 3

Parts Needed- No.3 QTY 1

Place the Left Plain Panel (No.3)

ush to the inside of the post

(No.19).

Fix the Left Plain Panel (No.3) to

the Post (No.19) using 4x70mm

Screws.

4x70mm Screws

Pre drill

hole

70mm

screw

Ariel View

19 19

Place the Post (No.18) attached to the

front panels against the Left Panel (No.3),

framing facing inwards.

Ensure that the panel sits ush to the

outside of the post.

Fix the Left Panel (No.3)to the Post

(No.10) using 4x70mm screws.

4x70mm Screws

Pre drill

hole

70mm

screw

Step 4

Parts Needed- No.6 QTY 2

- No. 18 QTY 2

Ariel View

P 7

Please retain product label and instructions for future reference

Place the Right Plain Panel (No.7)

against the front panel Post (No.18),

with the framing facing inwards.

Ensure that the panel sits ush to the

outside of the post.

Fix the Right Plain Panel (No.7) to the

Post (No.18) using 4x70mm screws.

4x70mm Screws

Step 5

Parts Needed- No.7 QTY 1

Ariel View

Step 6

Parts Needed- No.11 QTY 1

Pre drill

hole

70mm

screw

Place the Left Bar top (No.11) on top

of the Left Plain Panel (No.3).

Secure using 6x70mm screws going

through the Bar top cladding and into

the plain panel framing below.

Using 2x50mm screws, x the Left Bar

top to the back panel, ensuring that

the Bar top cladding sits ush with the

top of the back panel framing

2x50mm Screws

6x70mm Screws

Ariel View

Pre drill

hole

70mm

screw 50mm

screw

618

P 7

Please retain product label and instructions for future reference

P 8

Ariel View

Step 7

Parts Needed- No.10 QTY 2

Pre drill

hole

70mm

screw

Place the Plain Bar tops (No.10) on top

of the Front Panels (No.6).

Secure using 3x70mm screws per bar

top, going through the Bar top

cladding and into the front panel

framing below.

Using 2x50mm screws, x the Plain Bar

top to the Left Bar top from the

underside of the bar tops.

Using 2x50mm screws, x the Plain Bar

tops together in alternating pattern

from the underside of the bar tops

4x50mm Screws

6x70mm Screws

10 1022

Ariel View

Step 7A

Parts Needed- No.10 QTY 2

- No.22 QTY 1

Pre drill

hole

70mm

screw

Place the Plain Bar tops (No.10) and the

Plain Bar top Extension (No.22) on top of

the Front Panels (No.6).

Secure using 3x70mm screws per bar top,

going through the Bar top cladding and into

the front panel framing below.

Using 2x50mm screws, x the Plain Bar top

to the Left Bar top from the underside of the

bar tops.

Using 2x50mm screws per join, x the Plain

Bar tops and the Plain Bar top extension

together in alternating pattern from the

underside of the bar tops

6x50mm Screws

9x70mm Screws

Extension Pack

50mm

screw

50mm

screw

837mm

658mm 658mm

10 10

10 22

P 9

Please retain product label and instructions for future reference

P 8

Ariel View

Step 8

Parts Needed- No.9 QTY 1

Pre drill

hole

70mm

screw

Place the Right Bar top (No.9) on top

of the Right Plain Panel (No.7).

Secure using 5x70mm screws going

through the Bar top cladding and into

the plain panel framing below.

Using 2x50mm screws, x the Right

Bar top to the Plain Bar top (No.10)

from the underside of the bar tops

2x50mm Screws

5x70mm Screws

Step 9A

Parts Needed- No.20 QTY 3

Pre drill

hole

50mm

screw

Extension Pack

Step 9

Parts Needed- No.20 QTY 2

Pre drill

hole

50mm

screw

Place the bar supports (No.20)

underneath the bar tops as shown in the

illustration. Place the rst underneath the

Right Bar Top (No.9) ush to the edge of

the bar and the right plain panel (No7).

The second should be positioned centrally

between the Plain Bar Tops (No.10) ush

to the edge of the bar top and the Front

Panels (No.6)

Secure using 4x50mm screws per Bar

support (No.20)ensuring to o set the

screws location so to not split the bar

support.

8x50mm Screws

Place the bar supports (No.20) underneath

the bar tops as shown in the illustration.

Place the rst underneath the Right Bar Top

(No.9) ush to the edge of the bar and the

right plain panel (No7). The second and

third should be positioned centrally

between the Plain Bar Tops (No.10) and

the Plain Bar top Extension (No.22), ush

to the edge of the bar top and the Front

Panels (No.6).

Secure using 4x50mm screws per Bar

support (No.20)ensuring to o set the

screws location so to not split the bar

support.

12x50mm Screws

50mm

screw

20 20 20

20 20

Please retain product label and instructions for future reference

21mm

Step 10

Parts Needed- No.4 QTY 1

- No.5 QTY 1

Pre drill

hole

50mm

screw

Place the Right Gable (No.5) and the Left

Gable (No.4) between the Posts, the

front of the gables will sit ush to the top

of the front posts. The back of the gables

will sit 21mm above the back posts.

Secure each gable to the posts using

4x50mm screws. When securing to the

back post, oset the screws to ensure the

framing does not split

8x50mm Screws

Step 11A

Parts Needed- No.8 QTY 3

Pre drill

hole

50mm

screw

Extension Pack

Step 11

Parts Needed- No.8 QTY 2

Pre drill

hole

50mm

screw

Place the Top Panels (No.8) between

the front posts (No.20), position them

to be ush with the bottom of the

gables.

Secure the Top panels to the Posts

using 2x50mm screws.

Secure the Top panels together using

4x50mm screws in an alternating

pattern.

8x50mm Screws

Place the Top Panels (No.8) between

the the front posts (No.20), position

them to be ush with the bottom of

the gables.

Secure the Top panels to the Posts

using 2x50mm screws.

Secure the Top panels together using

4x50mm screws per join in an

alternating pattern.

12x50mm Screws

P 10

Andere Handbücher für 03PTMBPN0406BR-V1

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 0628WKNE0304LBDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0705SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02DTSHOPN0305-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634RARE0302ND1SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 06LOG016-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0705SDNW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTOVAX1006DDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OSBA0406DDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHPN0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01TDM0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0644LOG133-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0304SDNW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OVLPA0510PB-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0619RANE0325FGSD3TW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 06LOG173SG-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTOVAX0705SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 02DTSHAX05051W-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03WES1008-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01RAW2010DDOW-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 8x8 Waltons Vermont Summerhouse Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01GRO0806DD-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHCR0909GD4TW-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03BRN0705-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01RAW1010DDOW-V1 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung