Mercia Garden Products OSB APEX Gebrauchsanweisung

P 1

01OSBA0806DDFW-V1 & 01OSBA0806DDFW-V1-NW

8X6 OSB APEX

2mm Drill bit

x2 Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All building’s should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 880514

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eﬀort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

**Protim Aquatan T5 (621)**

Your building has been treated with Aquatan.

Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct

application of Aquatan solution and then allowed to dry.

Aquatan is a decorative ﬁnish to colour the wood, which is applied industrially to timber fence panels and

garden buildings.

Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl

sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.

Please retain product label and instructions for future reference

General Instructions

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied)

including a Phillips screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm

bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aﬀected during various weather conditions.

For the duration of heavy or extended periods of rain, swelling of the wood panels may

occur. Warping of the wood may also occur during excessive dry spells due to an interior

moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is

suggested that the outdoor building is sprayed with water during extended periods of

warm sunshine and sheltered as much as possible during rain or snow.

Our buildings are pre treated with a water based treatment**; this only helps to protect

the product during transit and for upto 3 months against mould. To validate your

guarantee and ensure longevity of the product, it is ESSENTIAL the building is treated

with a wood preserver within the ﬁrst three months of assembly and thereafter in

accordance with the manufactures recommendations. Care must be taken to ensure

the product is placed on a suitable base.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on ﬁrm ground, to prevent distortion. Refer to

diagrams for the base dimensions, The base should be slightly smaller than the external

measurement of the building, i.e. The cladding should overlap the base, creating a run

oﬀ for water. It is also recommended that the ﬂoor be at least 25mm above the

surrounding ground level to avoid ﬂooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in

the case of childrens products independently tested to EN71 level, we cannot accept

responsibility for your safety whilst erecting or using this product.

Refer to the instructions pages for you speciﬁc product code

P 7

01OSBA0806DDFW-V1 & 01OSBA0806DDFW-V1-NW

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Overall Dimensions:

Length = 2414mm

Width = 1905mm

Height = 1986mm

Base Dimensions:

Length = 2350mm

Width = 1753mm

01OSBA0806DDFW-V1

01OSBA0806DDFW-V1-NW

Building content

Fascia 1016mm x4

Fixed Window Strip 546mm x3 FW-V1 ONLY

Cover Trims 1575mm x4

Door Strip 1016mm

Ridge Bar 2304mm

Door Strip 530mm

Door Block 140mm x2

Finial x2

Door Gable Back Gable Plain Side

Qty 2 -NW only

Window Panel

FW-V1 ONLY

Floor Roof

Door

1 2 34

6 7

Door Beading Strip 1590mm x2

T Hinge

Qty 4

Plastic Window Cill

FW-V1 ONLY

Felt

Styrene Qty 2

FW-V1 ONLY

L-Bracket

Qty 2

Capping

Felt

Turn Button

Qty 3

Eaves Frame 1195mm x4

Nail Bag Felt Tacks x 100

20mm Screw x 14

30mm Black Screw x 3

30mm Screw x 79

50mm Screw x 28

40mm Screw x 44

Remove transportation

blocks from the bottom

of each panel before

beginning assembly. Each

Panel should have two

Pre Assembly

Fix the T Hinges onto the

doors and door frame as

shown. Ensure that the

screws go through the

cladding and into the

framing behind.

28x30mm screws

30mm

screw

Pre drill

hole

Place the ﬂoor on a ﬁrm and level base,

ensure the base has suitable drainage free

from areas where standing water can collect.

See the front page for base requirments.

Step 1

Do not secure the building to the

ﬂoor until the roof is ﬁtted. Fix the

panels onto the ﬂoor using 50mm

screws in alignment with the ﬂoor

joists

Fix the corners with 50mm screws

as shown in diagram.

Position the panels so there is equal spacing

between the ﬂoor and cladding on all 4 sides

Step 2

3x50mm Screws

Pre drill

hole

50mm

screw

Step 3

9x50mm Screws

Fix the corners with 50mm

screws as shown in diagram.

Use for no

window buildings

Pre drill

hole

50mm

screw

Step 4

8x20mm Screws

Place the ridge bar in between the front

and back gables. Ensure the top corners

of the ridge bar sit ﬂush with the top

points of the door gable. Fix the ridge bar

to the gable using one L bracket for each

end.

Fix with 4x20mm screws each

20mm

screw

Pre drill

hole

P 9

Step 5

Fix two eaves frames to each roof sheet

using 3x30mm screws per eave.

Fix the roof sheets to the roof ensuring

they come together at the top using

40mm screws directly through the roof

sheet at the top. Make sure to attach the

roofs to the ridge bar.

30mm

screw

12x 30mm Screws

28x 40mm Screws

40mm

screw

Pre drill

hole

Pre drill

hole

Step 6

bOnce the roof is ﬁxed

attach the building to

the ﬂoor with 50 mm

screws.

16x 50mm Screws

50mm

screw

Pre drill

hole

100x Tacks

Felt

tacks

Step 7

Cut the felt into 2 sheets at 2490mm and

ﬁx onto the roof using felt tacks as shown

in diagram ensuring there is 50mm

overhang around the sides. Cut the

capping felt to 2490mm and ﬁx over the

centre of the apex as shown in the

diagram ensuring there is 50mm over-

hang around the sides.

HANDLE

WITH CARE

P 10

Fit the Cover Trims to the front

and back of the building as

shown in the illustration using

30mm screws. Trim the length

of the cover trims to the

required size before ﬁtting if

necessary.

Pre drill to avoid splitting.

12x30mm Screws

Step 8 30mm

screw

Pre drill

hole

Step 9

16x40mm Screws

Attach the faiscas to the roof

leaving a slight overhang at the

top.

Fit the fascias to the roof over

the felt and secure in place with

40mm screws as shown.

Pre drill to avoid splitting.

17 8

40mm

screw

Pre drill

hole

Step 10

Fit the styrene sheets on top of

the window cill.

When positioning the styrene

sheets ensure there is an equal

distance between them and at

either side of the windows.

Fix the window strips to the two

pieces of framing that sit

alongside the outside edges of

the window with 3x30mm

screws for each strip.

Attach the three window strips

at either side of the windows

using 3x30mm screws each.

Make sure the screws enter the

framing in the window panel

and not the styrene.

9x30mm Screws

For the no window version go to step 11

30mm

screw Pre drill

hole

6x30mm Screws

30mm

screw Pre drill

hole

Place the

plastic window

cill onto the

Window Panel

and silicone in

place as shown

on both

diagrams to the

left.

Side View

Styrene

Window Cill

SILICONE

SEALANT

P 11

Step 11

Use 4x30mm Screws to ﬁx

each beading strip onto the

door gable. Ensure that the

screw is parallel with the

door frame when ﬁxing the

strip to the door gable as

shown in the close up view.

Attach the turn button to

the top and bottom door

blocks with 1x30mm screw

for each one.

First line up the door blocks

at the top and bottom of the

doors. Then ﬁx with

2x30mm screws by screwing

through the outside of the

door into the block.

8x30mm Screws

2x30mm Black Screws

4x30mm Screws

b ca

20mm

screw

30mm

screw

30mm

screw

30mm

screw

Use 5x20mm screws to ﬁx

the door strips to the right

hand door.

Note - Door Strips must be

attached to right hand door

Use 1x30mm black screw to

ﬁx the turn button onto the

left hand door.

5 x 20mm Screws

1x 30mm Black Screw

Step 12

It is ESSENTIAL that you apply wood

treatment immediately after the building

has been assembled.

AFTER TREATMENT:

score around protective

cover on glazing and

carefuly peel

covering back

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03TGCORSE0409-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1206DDOP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTJER0806-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0305SDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVRA0806SDFW-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01PTOSBA0306DDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03OVLPBRN0705-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHDB0808DDOP-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0619PNSH1227FBSD-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02CHY0404-V3 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01RAW1210DDOW-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628RASH0302FBSDNW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products SELF BUILD PACK Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01SHPSTR0402-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHAX0608FGD4MW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02HIDE0705-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628AXNE0403HGDD1SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01PTSHPWOR1010DDOW-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products POPPY PLAYHOUSE Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHPN0806FGD1TW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01COMGRN0406-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0608SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03HEL1010DDFW-V2 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung