Mercia Garden Products 0628LOG131-V4 Gebrauchsanweisung

P 1

0628LOG131-V4 Log Cabin With Return (3x4m)

0628LOG131-V4: T&G roof and oor

2mm Drill bit

Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All buildings should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

Please retain product label and instructions for future reference

General Instructions

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied)

including a Phillips screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm

bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather conditions.

For the duration of heavy or extended periods of rain, swelling of the wood panels may

occur. Warping of the wood may also occur during excessive dry spells due to an interior

moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is

suggested that the outdoor building is sprayed with water during extended periods of

warm sunshine and sheltered as much as possible during rain or snow.

BUILDING A BASE

When thinking about where the building and base are going to be constructed:

Ensure that there will be access (60cm) to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to

diagrams for the base dimensions. The base should be slightly smaller than the external

measurement of the building, i.e. The cladding should overlap the base, creating a run

o for water. It is also recommended that the oor be at least 25mm above the

surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in

the case of childrens products independently tested to EN71 level, we cannot accept

responsibility for your safety whilst erecting or using this product.

Refer to the instructions pages for your specic product code

For ease of assembly use a

rubber mallet to t the log

boards. Do NOT use a heavy

hammer.

Ensure to measure and check before cutting

boards.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

It is advisable to use a hand

saw when cutting roof and

oor boards.

To ensure log boards are even, use a spirit

level to check each layer has been installed

correctly.

Double Door Pack*

P 2

Overall Dimensions:

Width = 4028mm

Depth = 3139mm

Height = 2600mm

Base Dimensions:

Width = 3803mm

Depth = 2799mm

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Short Window Pack*

QTY 2

131 Gable A2996mm

AI-0628LOG131-V3GFS

(full non-return side)

131 Gable D2996mm

AI-0628LOG131-V3FGRS

(return side - gable is un-xed for assembly purposes)

131 Gable A1105mm

AI-0628LOG131-V3HGRS

(return side - gable is un-xed

for assembly purposes)

Starter Board - 28x66x4000mm

LB28RT66-A-4000

Starter Board - 28x66x2220mm

LB28RT66-A-2220

Starter Board - 28x66x2000mm

LB28RT66-A-2000

Log Board - 28x120x2111mm QTY 6

LB28-A-2111

Log Board - 28x120x2000mm QTY 6

LB28-A-2000

Log Board - 28x120x2996mm QTY 19

LB28-A-2996

Log Board - 28x120x2996mm

LB28-ADF-2996

Log Board - 28x120x4000mm QTY 19

LB28-A-4000

Log Board - 28x120x4000mm

LB28-ADF-4000

Log Board - 28x45x4000mm

LB28RG45-AF-4000

Log Board - 28x45x4000mm

LB28RG45-A-4000

Log Board - 28x120x681mm QTY 24

LB28-B-681

Log Board - 28x120x625mm QTY 24

LB28-B-625

Log Board - 28x120x325mm QTY 36

LB28-B-325

Log Board - 28x120x2220mm QTY 2

LB28-A-2220

Log Board - 28x45x2220mm

LB28RG45-A-2220

Log Board - 28x120x1105mm QTY 19

LB28-A-1105

Roof Purlin - 45x120x4004mm QTY 2

F45120-A-4004

Roof Purlin - 45x120x4004mm

F45120-AF-4004

0628LOG131-V4

Felt Tacks x257

70mm Screw x92

Felt

Nail Bag

40mm Screw x564

30mm Screw x126

10mm Screw x4

Pre-assembly

*Please note:

Each board interlocks at

either end in a staggered pattern.

Before securing ensure that the boards

are tted properly in their respective

tongues and grooves.

70mm Bolt Set x16

*All components for the Windows and Doors are

shown in the Windows and Doors instruction packs.

P 3

Please retain product label and instructions for future reference

Veranda Post - 70x70x2001mm

F7070-2001 (Notched)

Fascia - 16x120x1601mm QTY 4

S16120-1601 (Angled)

Fascia - 16x120x4036mm QTY 2

S16120-4036

Eaves Frame - 27x44x4000mm QTY 2

F2744-4000

Roof Board - 16x121x1600mm QTY 74

MB16-C-1600

Floor Board - 16x121x1862mm QTY 18

MB16-C-1862

Floor Board - 16x121x2748m QTY 18

MB16-C-2748

Bearer - 44x44x2804mm QTY 2

F4444-2804-PT

Bearer - 44x44x3720mm QTY 12

F4444-3720-PT

Storm Brace - 27x44x200mm QTY 8

F2744-200

Veranda Board - 16x120x880mm QTY 14

SR16120-880

Log Board - 28x120x2220mm

LB28-AD-2220

Post Plate

Closure Trim - 16x28x2400mm (approx length) QTY 14

S1628-2400

Roof Spacers QTY 5

PI-07-0208 (20x100x2mm)

Pre drill

hole

Example picture

2 screws per bearer per end.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

Please retain product label and instructions for future reference

IMPORTANT: Pre-drill before xing screws.

Step 1

Parts needed - No. 32 QTY 2

No. 33 QTY 12

Lay the bearers A& B(No. 32

& No. 33) onto a rm and level

surface (free from areas where

standing water can collect) as shown

in the illustration.

Fix the framing together at each

corner using 8x70mm screws,

ensuring the frame is ush.

8x70mm Screws

70mm

screw

Step 2 (See Pre-Assembly)

Parts needed - No. 6 QTY 1

No. 7 QTY 1

No. 8 QTY 1

No. 9 QTY 1

No. 11 QTY 1

No. 22 QTY 1

Place the boards (No. 6, 7, 8,

9, 11 & 22) on to the

assembled base frame along

the longest sides.

*Ensure the notches at

either end of each board are

ush and level with the ends

of the frame.

Fix each of the starter boards

to the frame by screwing

through the notch into the

frame as shown in the

illustration.

6x70mm Screws

Pre drill

hole

70mm

screw

Pre drill

hole

70mm

screw

Following the same

method, arrange the

remaining bearer’s (B) (No. 33)

inside the assembled frame

*Ensure there is an equal

amount of space between

each frame.

Fix the framing together at

each corner using 10x70mm

screws, ensuring the frame is

ush.

40x70mm Screws

Please Note:The starters ( No’s. 38 & 39)

can be arranged on either side ( allowing

the doors to be placed on the left or right

the building) depending on your needs.

P 5

Please retain product label and instructions for future reference

IMPORTANT: Pre-drill before xing screws.

Step 3 (See Pre-Assembly)

Parts needed - No. 9 QTY 5

No. 10 QTY 6

No. 11 QTY 5

No. 13 QTY 6

No. 19 QTY 12

No. 22 QTY 5

Following the same method

outlined in Pre-Assembly, lay

the rst 6 boards (No’s. 9, 10,

11, 13, 19 & 22) onto the

starter boards to create your

rst level.

*Ensure that the boards are

level and ush with each

other as you lay each one.

Please Note: The short boards at the

front of the building (either side of

the door and window opening’s)

can be placed either side depending

on your needs.

Step 4

Once you have laid 6 log boards (o

of the starter ) up the door section,

slide the assembled door frame (No.

2) assembly over the boards resting

the frame on top of the starter board.

*Please note:This image is for illustra -

tive purposes and may dier from

your choice in product ( regarding

door position). Nevertheless the

process of tting the door frame is

the same.

**Please Note:The short boards at

the

front of the building (either side of

the door and window opening’s) can

be placed either side depending on

your needs.

P 6

Please retain product label and instructions for future reference

Step 5(See Pre-Assembly)

Parts needed - No. 11 QTY 6

No. 13 QTY 6

No. 17 QTY 12

No. 18 QTY 12

No. 19 QTY 12

No. 22 QTY 6

Following the same method

outlined in Pre-Assembly , lay

the next 6 boards (No’s. 11, 13,

17, 18, 19 & 22) onto the

assembly to create your second

level.

*Doors can be hung once the

boarding has enclosed the

door frame by 12-13 boards,

refer to door installation

instructions, if not, you can

install the door at step 7.

*Ensure that the boards are

level and ush with each

other as you lay each one.

**Doors can be hung once the

boarding has enclosed the

door frame.

***Please Note: The short boards placed

to create the opening’s for the doors &

windows can be placed either side

depending on your needs.

IMPORTANT: Pre-drill before xing screws.

Step 6

Once you have laid the second

level of boards onto the assembly

slide the window(s)(No. 1)

between the smaller boards and

rest on to the longer board.

*Ensure the boards are level with

each end.

*Please note: This image is for

illustrative purposes and may

dier from your choice in product

(regarding window position).

Nevertheless the process of tting

the window is the same.

P 7

Please retain product label and instructions for future reference

Step 8

Parts needed - No. 37 QTY 18

Fix the Veranda Boards (No. 37)

to the oor bearers using

7x30mm screws per board.

Some boards need to be

notched to t. Cut a

notch 98x28mm on one

corner.

Fix the remaining boards

17mm apart.

The nal board will need

to be shortened by

28mm.

126x30mm Screws

Step 7(See Pre-Assembly)

Parts needed - No. 11 QTY 6

No. 13 QTY 6

No. 17 QTY 12

No. 18 QTY 12

No. 19 QTY 12

No. 22 QTY 6

Following the same method

outlined in Pre-Assembly , lay

the remaining boards (No’s. 11,

13, 17, 18, 19 & 22)onto the

assembly to bring the board

level to the top of the window

and door frames.

*Ensure that the boards are

level and ush with each

other as you lay each one.

**Doors can be hung once the

boarding has enclosed the

door frame.

IMPORTANT: Pre-drill before xing screws.

19 18

17 37

*Cut to t

Pre drill

hole

30mm

screw

P 8

Please retain product label and instructions for future reference

Step 12 (See Pre-Assembly)

Parts needed - No. 3 QTY 1

No. 4d QTY 1

No. 5c QTY 1

Place the gable top (No. 3) onto the

assembly and x into position by

screwing through the notches into

the boards below.

Part No’s. 4d & 5c are the bottom

boards from the gable only (gable

is un-xed for assembly purposes)

rest these into position and secure

through the notches in the board.

*Ensure that the boards are level

and ush with each other as you

lay each one.

**Ensure to stagger the screws to

ensure not to collide.

6x70mm Screws

Step 10 (See Pre-Assembly)

Parts needed - No. 11 QTY 1

No. 12 QTY 1

No. 22 QTY 1

No. 25 QTY 1

No. 39 QTY 1

Following the same method

outlined in Pre-Assembly, lay

the next three boards (No’s. 11,

12 & 22) onto the assembly as

shown in the illustration.

*Ensure that the boards are

level and ush with each

other as you lay each one.

Fix each board to the one

below using 1x70mm screw per

side.

Fix the bottom part of the Post

Plate (No. 39) to the veranda

using 10mm screws. Place the

Veranda Post (No. 25) onto the

protruding (ensuring the board

sits into the notch).

Secure into place using

2x70mm screws at the top and

adjust the nut to suit the post.

8x70mm Screws

4x10mm Screw

Pre drill

hole

70mm

screw

10mm

screw

Step 11 (See Pre-Assembly)

Parts needed - No. 13 QTY 1

No. 14 QTY 1

No. 36 QTY 1

Following the same method

outlined in Pre-Assembly,

x the next three boards

(No’s. 13, 14 & 36) onto

assembly as shown in the

illustration.

Pre drill

hole

70mm

screw

Step 9

Parts needed - No. 39 QTY 1

No. 25 QTY 1

Fix the top section of the post

plate to the base of the post

using 4x40mm screws as

shown in the illustration.

4x40mm Screws

40mm

screw

P 9

Please retain product label and instructions for future reference

Pre drill

hole

70mm

screw

Step 13 (See Pre-Assembly)

Parts needed - No. 20 QTY 1

Place the second Log Board

(No. 20) above the doors as

shown in the illustration, xing

the board into position through

each notch with 2x70mm

screws.

*Ensure that the boards are

level and ush with each

other as you lay each one.

**Ensure to stagger the screws

to ensure not to collide.

2x70mm Screws

Step 14 (See Pre-Assembly)

Parts needed - No. 4c QTY 1

No 5b QTY 1

Part No’s. 4c & 5b) are the second

boards from the gable only

(gable is un-xed for assembly

purposes) rest these into

position and secure through

the notches in the board.

*Ensure that the boards are

level and ush with each

other as you lay each one.

**Ensure to stagger the screws

to ensure not to collide.

4x70mm Screws

Pre drill

hole

70mm

screw

Step 15 (See Pre-Assembly)

Parts needed - No. 21 QTY 1

Keep adding the remaining

boards onto the front and

gables following the same

method outlined in the

previous steps.

*Ensure that the boards are

level and ush with each

other as you lay each one.

**Ensure to stagger the screws

to ensure not to collide.

2x70mm Screws

Pre drill

hole

70mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 16 (See Pre-Assembly)

Parts needed - No. 4a QTY 1

No 4b QTY 1

No. 5a QTY 1

Parts No. 4a, 4b & 5a are the last

log boards from the gables; rest

these into position and secure

through the notches in the board.

*Ensure that the boards are

level and ush with each other

as you lay each one.

**Ensure to stagger the screws

to ensure not to collide.

2x70mm Screws

Pre drill

hole

70mm

screw

4b 4a

IMPORTANT: Pre-drill before xing screws.

P 10

Please retain product label and instructions for future reference

Pre drill

hole

Step 18

Parts needed - No. 23 QTY 2

No. 24 QTY 1

Align the roof purlin(s) (No. 23)

into the cut out slots on each gable top at

the rear of the building ensuring each

roof purlin interlocks the boards.

Following the

same outlined method place the

remaining roof purlin (No. 24 - 3x notches )

into cut out slots at the front of the

building ensuring the roof purlin

interlocks the boards.

Secure the purlin at each end by

screwing through the bars into the

boards (ensure to pre-drill to avoid

the boards splitting) using 4x70mm

screws per purlin.

*Please note:The gable shown is for

illustrative purposes and may dier

in width from your choice in product.

Nevertheless, despite any dierences

the process of xing the purlins

is the same.

12x70mm Screws

70mm

screw

Step 17 (See Pre-Assembly)

Parts needed - No. 15 QTY 1

No. 16 QTY 1

Place the log boards (No’s.

15 & 16) onto the front and

rear of the building securing

the boards in to place using

5x70mm as shown in the

illustration.

*Ensure that the boards are

level and ush with each

other as you lay each one.

**Ensure to stagger the screws

to ensure not to collide.

2x70mm Screws

Pre drill

hole

70mm

screw

Rear Front

IMPORTANT: Pre-drill before xing screws.

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 10DTSHPN0804-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 10DTBARK0804-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0644LOG208-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03VER0808-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628RANE0403HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634RARE0302ND1SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVRA0604SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03LBRO1208-V7 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVAX0705SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 8x8 Waltons Vermont Summerhouse Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01SHPWOR1610DDOW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHHP0806HGD4MW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 05DTMBCH0304-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0406DDNW-V Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTGRODB1008-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 06LOG015-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0705SDNW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OVLPA08DDGP-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 02CHY0404-V3 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0644CVNE0403HGDD3SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OVLPA0705SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01RAW1010DDOW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01GRODB1008-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHCV1208HGD4MW-V1 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung