Metrohm 930 Compact IC Flex Bedienungsanleitung

930 Compact IC Flex

930 Compact IC Flex Oven/SeS/PP

Manual

8.930.8019EN / v3 / 2023-03-31

Metrohm AG

CH-9100 Herisau

Switzerland

+41 71 353 85 85

[email protected]

www.metrohm.com

930 Compact IC Flex

930 Compact IC Flex Oven/SeS/PP

2.930.2500

Manual

8.930.8019EN / v3 / 2023-03-31

Technical Communication

Metrohm AG

CH-9100 Herisau

This documentation has been prepared with great care. However, errors

can never be entirely ruled out. Please send comments regarding possible

errors to the address above.

Disclaimer

Deficiencies arising from circumstances that are not the responsibility of

Metrohm, such as improper storage or improper use, etc., are expressly

excluded from the warranty. Unauthorized modifications to the product

(e.g. conversions or attachments) exclude any liability on the part of the

manufacturer for resulting damage and its consequences. Instructions and

notes in the Metrohm product documentation must be strictly followed.

Otherwise, Metrohm's liability is excluded.

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ Table of contents

930 Compact IC Flex Oven/SeS/PP (2.930.2500) ￭￭￭￭￭￭￭￭ III

Table of contents

1 Introduction 1

1.1 Instrument description ......................................................... 1

1.2 Accessories and additional information ............................. 3

1.3 Symbols and conventions .................................................... 3

2 Safety 5

2.1 Intended use ......................................................................... 5

2.2 Responsibility of the operator ............................................. 5

2.3 Requirements for operating personnel ............................... 6

2.4 Safety instructions ................................................................ 6

2.4.1 General notes on safety ........................................................... 6

2.4.2 Electrical safety ........................................................................ 6

2.4.3 Tubing and capillary connections ............................................. 7

2.4.4 Flammable solvents and chemicals ........................................... 8

2.4.5 Recycling and disposal ............................................................. 8

3 Overview of the device 9

3.1 Front ...................................................................................... 9

3.2 Rear ...................................................................................... 10

3.3 Feed-throughs for capillaries and cables .......................... 12

4 Installation 15

4.1 Setting up the instrument .................................................. 15

4.1.1 Packaging .............................................................................. 15

4.1.2 Checks .................................................................................. 15

4.1.3 Location ................................................................................ 15

4.2 Capillary connections in the IC system ............................. 15

4.3 Removing transport locking screws .................................. 18

4.4 Connecting the drainage tubing and leak sensor ............ 19

4.4.1 Installing the drainage tubing ................................................ 19

4.4.2 Connecting the leak sensor .................................................... 21

4.5 Column oven ....................................................................... 21

4.6 Connecting the eluent bottle ............................................. 22

4.7 Installing the high-pressure pump .................................... 26

4.8 Installing an inline filter ..................................................... 27

4.9 Installing the pulsation absorber ...................................... 27

Table of contents ￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭

IV ￭￭￭￭￭￭￭￭ 930 Compact IC Flex Oven/SeS/PP (2.930.2500)

4.10 Injection valve ..................................................................... 28

4.11 Metrohm Suppressor Module (MSM) ............................... 30

4.11.1 Inserting the rotors ................................................................ 31

4.11.2 Connecting the Metrohm Suppressor Module (MSM) ............. 33

4.12 Peristaltic pump .................................................................. 38

4.12.1 Installing the peristaltic pump ................................................ 38

4.12.2 Mode of operation for the peristaltic pump ........................... 42

4.13 Metrohm CO2 Suppressor (MCS) ....................................... 43

4.13.1 General information on the MCS ........................................... 43

4.13.2 Connecting the MCS ............................................................. 43

4.13.3 Installing the adsorber cartridge ............................................. 45

4.14 Installing the conductivity detector .................................. 47

4.15 Installing the amperometric detector ............................... 48

4.16 Connecting the instrument to a computer ....................... 48

4.17 Connecting the instrument to the power grid ................. 49

4.18 Initial start-up ..................................................................... 50

4.19 Connecting and rinsing the guard column ....................... 52

4.20 Connecting and rinsing the separation column ............... 54

4.21 Conditioning ........................................................................ 57

5 Operation 59

6 Operation and maintenance 60

6.1 IC system ............................................................................. 60

6.1.1 Operation .............................................................................. 60

6.1.2 Care ...................................................................................... 60

6.1.3 Maintenance by Metrohm Service .......................................... 60

6.1.4 Shutting down and recommissioning ..................................... 61

6.2 Capillary connections ......................................................... 62

6.3 Servicing the door .............................................................. 62

6.4 Column oven – Replacing the capillaries .......................... 62

6.5 Handling the eluent ............................................................ 64

6.5.1 Manufacturing eluent ............................................................ 64

6.5.2 Changing the eluent .............................................................. 65

6.6 Notes on operating the high-pressure pump ................... 65

6.7 Servicing the high-pressure pump .................................... 66

6.8 Servicing the inline filter .................................................... 79

6.9 Servicing the pulsation absorber ...................................... 82

6.10 Injection valve ..................................................................... 82

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ Table of contents

930 Compact IC Flex Oven/SeS/PP (2.930.2500) ￭￭￭￭￭￭￭￭ V

6.11 Metrohm Suppressor Module (MSM) ............................... 82

6.11.1 Notes for operating the Metrohm Suppressor Module

(MSM) ................................................................................... 82

6.11.2 Taking care of the suppressor housing ................................... 83

6.11.3 Servicing the Metrohm Suppressor Module (MSM) ................. 83

6.12 Peristaltic pump .................................................................. 91

6.12.1 Notes on operating the peristaltic pump ................................ 91

6.12.2 Servicing the peristaltic pump ................................................ 91

6.13 Maintenance on the Metrohm CO2 Suppressor (MCS) .... 93

6.13.1 Replacing the CO2 adsorption cartridge CW ........................... 93

6.14 Detector maintenance ........................................................ 94

6.15 Rinsing the sample path .................................................... 94

6.16 Separation column ............................................................. 95

6.16.1 Separating efficiency .............................................................. 95

6.16.2 Protecting the separation column .......................................... 96

6.16.3 Storing the separation column ............................................... 96

6.16.4 Regenerating the separation column ...................................... 96

7 Troubleshooting 97

7.1 ............................................................................................. 97

8 Technical specifications 102

8.1 Reference conditions ........................................................ 102

8.2 Instrument ......................................................................... 102

8.3 Ambient conditions .......................................................... 102

8.4 Housing ............................................................................. 103

8.5 Weight ............................................................................... 103

8.6 Leak sensor ....................................................................... 103

8.7 Column oven ..................................................................... 103

8.8 High-pressure pump ......................................................... 104

8.9 Injection valve ................................................................... 105

8.10 Metrohm Suppressor Module (MSM) ............................. 105

8.11 Peristaltic pump ................................................................ 105

8.12 Metrohm CO2 Suppressor (MCS) ..................................... 105

8.13 Detector ............................................................................ 106

8.14 Power connection ............................................................. 106

8.15 Interfaces .......................................................................... 106

Index 107

Table of figures ￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭

VI ￭￭￭￭￭￭￭￭ 930 Compact IC Flex Oven/SeS/PP (2.930.2500)

Table of figures

Figure 1 Front ................................................................................................. 9

Figure 2 Rear ................................................................................................ 10

Figure 3 Feed-throughs on the door .............................................................. 12

Figure 4 Openings for capillaries and cables .................................................. 13

Figure 5 Ducts for capillaries ......................................................................... 14

Figure 6 Removing the transport locking screws ............................................ 18

Figure 7 Installing the eluent bottle cap ........................................................ 22

Figure 8 Installing the tubing weighting and aspiration filter .......................... 24

Figure 9 High-pressure pump with purge valve .............................................. 26

Figure 10 Inline filter ....................................................................................... 27

Figure 11 Pulsation absorber ........................................................................... 28

Figure 12 Exchanging the sample loop ............................................................ 29

Figure 13 Metrohm Suppressor Module (MSM) – Connection capillaries .......... 34

Figure 14 Peristaltic pump ............................................................................... 42

Figure 15 Connecting the MCS ....................................................................... 44

Figure 16 Column oven .................................................................................. 63

Figure 17 High-pressure pump – Parts ............................................................. 66

Figure 18 High-pressure pump – Cross-section ................................................ 73

Figure 19 Tool for piston seal (6.2617.010) ..................................................... 74

Figure 20 Removing the piston cartridge from the pump head ........................ 74

Figure 21 Inserting the piston seal into the tool ............................................... 75

Figure 22 Parts of the piston cartridge ............................................................ 76

Figure 23 Inline filter – Removing the filter ...................................................... 80

Figure 24 Parts of the Metrohm Suppressor Module (MSM) ............................ 83

Figure 25 Pump tubing connection – Replacing the filter ................................. 92

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 1 Introduction

930 Compact IC Flex Oven/SeS/PP (2.930.2500) ￭￭￭￭￭￭￭￭ 1

1 Introduction

1.1 Instrument description

The 930 Compact IC Flex is a robust ion chromatograph. It is distinguished

by:

￭Its intelligence: All of the functions are monitored, optimized and docu-

mented in an FDA-compatible manner. Intelligent components, such as

iColumns, save important data onto a chip.

￭Its compact design: It has a small footprint.

￭Its transparency: All components are easily accessible and located for

simple visibility and can be monitored during operation through a large

window.

￭Its safety: The wet end and the electronics are physically separated.

This prevents fluids from coming into contact with the electronics to a

large extent. A leak sensor is integrated into the wet end.

￭Its environmental compatibility.

￭Its low noise emission.

￭The intelligent MagIC Net software.

The 930 Compact IC Flex is operated using the MagIC Net software. A

USB cable is used to connect the device to a computer with MagIC Net

installed. The intelligent software detects the device automatically and

checks its functionality. The software controls and monitors the device,

evaluates the measured data and manages it in a database.

The 930 Compact IC Flex Oven/SeS/PP consists of the following modules:

Housing

The sturdy housing contains the instrument's electronic components,

including their interfaces and one connector for a separation column. In

addition, the housing provides space for a conductivity detector or an

amperometric detector. Capillaries and cables can be fed into and out of

the instrument through several openings.

Leak sensor

The leak sensor detects leaking liquid that collects in the instrument's base

tray. Liquid that leaks in the instrument is routed to the base tray using

drainage tubing and detected there.

Column oven

The column oven regulates the temperature for the separation column

and the eluent, thereby providing stable measuring conditions. There is a

column holder with chip reader in the column oven.

1.1 Instrument description ￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭

2￭￭￭￭￭￭￭￭ 930 Compact IC Flex Oven/SeS/PP (2.930.2500)

High-pressure pump

The intelligent and low-pulsation high-pressure pump pumps the eluent

through the IC system. It is equipped with a chip where its technical speci-

fications and "life history" (operating hours, service data, etc.) are stored.

Inline filter

Inline filters protect the separation column reliably from potential contam-

ination from the eluent. The filter pads with 2 µm pore size can be

replaced quickly and easily. They remove particles from the solutions, such

as bacteria and algae.

Pulsation absorber

The pulsation absorber protects the separation column from damage

caused by pressure fluctuations, e.g. when the injection valve is switched,

and reduces interfering pulsations during highly sensitive measurements.

Injection valve

The injection valve connects the eluent path to the sample path. By a

quick and precise switching of the valve, a quantity of sample solution

defined by the size of the sample loop is injected and flushed to the sepa-

ration column with the eluent.

Metrohm Suppressor Module (MSM)

The chemical suppressor MSM consists of the suppressor drive, a rotor

and, where applicable, an adapter. The suppressor drive gives you the flex-

ibility to use different rotors according to the principle "one drive – many

rotors". Suppression rotors with different capacities and construction or a

rotor for sample preparation (SPM Rotor) are readily interchangeable with

appropriate adapters as needed. The rotors are not included in the instru-

ment's scope of delivery. The rotor required for the application and any

adapter that is required must be ordered separately.

Peristaltic pump

The peristaltic pump is used for pumping sample and auxiliary solutions. It

can rotate in both directions.

Metrohm CO2 Suppressor (MCS)

The Metrohm CO2 Suppressor (MCS) removes the CO2 from the eluent

stream. This lowers the background conductivity, improves detection sen-

sitivity and minimizes the injection peak and system peak.

Detector

Metrohm offers a series of different detectors for various analysis tasks. A

suitable detector type must be ordered as a separate device.

Andere Handbücher für 930 Compact IC Flex

Inhaltsverzeichnis

Andere Metrohm Laborausrüstung Handbücher

Metrohm

Metrohm 801 Bedienungsanleitung

Metrohm

Metrohm 930 Compact IC Flex Bedienungsanleitung

Metrohm

Metrohm 945 Professional Detector Vario - Conductivity &... Bedienungsanleitung

Metrohm

Metrohm 930 Compact IC Flex Oven/ChS/Deg Bedienungsanleitung

Metrohm

Metrohm 807 Bedienungsanleitung

Metrohm

Metrohm OMNIS Titrator Bedienungsanleitung

Metrohm

Metrohm Titrino 784 KFP Bedienungsanleitung

Metrohm

Metrohm 930 Compact IC Flex ChS Bedienungsanleitung

Metrohm

Metrohm NIRS Vial Heater Bedienungsanleitung

Metrohm

Metrohm 889 IC Sample Center Basic Bedienungsanleitung

Metrohm

Metrohm 889 Bedienungsanleitung

Metrohm

Metrohm 803 Ti Stand Bedienungsanleitung

Metrohm

Metrohm 915 KF Ti-Touch Bedienungsanleitung

Metrohm

Metrohm 801 Bedienungsanleitung

Metrohm

Metrohm Eco KF Titrator Bedienungsanleitung

Metrohm

Metrohm 751 GPD Titrino Bedienungsanleitung

Metrohm

Metrohm 917 Coulometer Bedienungsanleitung

Metrohm

Metrohm 763 PVC Thermomat Bedienungsanleitung

Metrohm

Metrohm 832 KF Thermoprep Bedienungsanleitung

Metrohm

Metrohm 761 Compact IC Bedienungsanleitung

Metrohm

Metrohm OMNIS Titrator Bedienungsanleitung

Metrohm

Metrohm 663 VA Stand Bedienungsanleitung

Metrohm

Metrohm 728 Bedienungsanleitung

Metrohm

Metrohm 793 IC Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung