Metrologic Stratos MS2x20 Series Montage- und Bedienungsanleitung

METROLOGIC INSTRUMENTS, INC.

MS2x20 Stratos®Series

Configuration Addendum

Mettler Toledo Diva Scale

work may be reproduced, transmitted, or stored in any form or by any means

without prior written consent, except by reviewer, who may quote brief

passages in a review, or provided for in the Copyright Act of 1976.

Trademarks

Metrologic is a registered trademark of Metrologic Instruments, Inc.

Products identified in this document are hereby acknowledged as

trademarks, registered or otherwise, of Metrologic Instruments, Inc. or their

respective companies.

TABLE OF CONTENTS

IMPORTANT NOTES -BEFORE YOU START ................................................................. 1

Important Bar Codes

Scale Save Data Bar Code .................................................................... 2

Scale Type Bar Code ............................................................................. 2

SCALE/LOAD CELL CONFIGURATION BAR CODES

Single or Dual Cable Scale Configuration Bar Codes

Unit Configuration (Pounds)................................................................... 3

Unit Configuration (Kilograms) ............................................................... 4

SCALE CONFIGURATION BAR CODES

Single or Dual Cable Scale Configuration Bar Codes

Pole Display Configuration..................................................................... 5

Scale Settling Filter Configuration .......................................................... 7

Scale Internal Beeper............................................................................. 9

Zero Cursor.......................................................................................... 10

Quantitative Separator ......................................................................... 11

Dual Cable Scale Configuration Bar Codes

Scale Protocols .................................................................................... 12

Scale COM Port Settings (Baud Rate) ................................................. 18

Scale COM Port Settings (Data Bits & Parity)...................................... 20

Single Cable Scale Configuration Bar Codes

Set Scale for Single Cable Communication ......................................... 23

SCANNER CONFIGURATION BAR CODES

Dual Cable Scanner Configuration Bar Codes

Dual Cable Scanner Mode ................................................................... 24

Dual Cable Scanner OPOS Mode........................................................ 24

Various Dual Cable Scanner Mode ...................................................... 25

IBM 3rd Generation 46xx ...................................................................... 26

IBM OEM Full Speed USB ................................................................... 26

iii

TABLE OF CONTENTS

Single Cable Scanner Protocols for P.O.S. Compatibility

MSS Global.......................................................................................... 27

ISS45 ................................................................................................... 28

OPOS................................................................................................... 29

Retailix / NCR....................................................................................... 30

Retailix / OPOS .................................................................................... 31

IT Retail................................................................................................ 32

IBM Self Checkout System .................................................................. 33

Various RS232 Single Cable Codes .................................................... 34

IBM 3rd Generation 46xx ...................................................................... 35

IBM OEM Full Speed USB ................................................................... 36

Additional POS Data Formatting

Full Speed USB Table Top/Handheld .................................................. 37

Special Function ACK .......................................................................... 39

Prefix/Suffix.......................................................................................... 40

3x-30 Acknowledge Responses ........................................................... 41

Special Function Command Responses .............................................. 42

BCC in POS Communications ............................................................. 46

3 Scale Status Bytes ............................................................................ 47

Scale Options....................................................................................... 48

Remote Display.................................................................................... 49

StratosSTATS ...................................................................................... 50

Additional POS Related Functions

Scanner Beep on Weight Sent............................................................. 53

Restrict In-Store Codes........................................................................ 54

Scale Shadow Mode ............................................................................ 55

Scanner Razz on Not-On-File .............................................................. 56

Additional Scanner Configuration Bar Codes

Horizontal Depth of Field...................................................................... 57

Vertical Depth of Field.......................................................................... 59

TABLE OF CONTENTS

Auxiliary Port

StratosSCHOOL™............................................................................... 61

Quick Start for a Secondary Metrologic Scanner ................................. 62

EAS Bar Codes

EAS Device Types ............................................................................... 64

EAS Timeout ........................................................................................ 67

EAS Connection................................................................................... 72

Continuous Mode ................................................................................. 75

EAS Deactivation ................................................................................. 76

Sensormatic ScanMax Pro................................................................... 79

SCANNER TEST BAR CODES

Supplemental Tests..................................................................................... 81

Display Software Numbers................................................................... 81

CONTACT INFORMATION AND OFFICE LOCATIONS ..................................................... 82

IMPORTANT NOTES -BEFORE YOU START

It is important to read carefully the notes marked with a symbol on the pages

contained in this manual. Not all configuration codes are designed to be used for

both a single and dual cable scanner/scale system. Many of the configuration

bar codes require additional steps before the unit can be configured and placed

into service. Most of the bar codes in this addendum were designed to be used

with a Stratos model that includes a scale. The text marked with a symbol will

provide important additional information about the restrictions and uses of the bar

codes shown.

All of the bar codes in this manual require:

•The scanner/scale to have a firmware number of 15367 or higher

•All configuration bar codes must be scanned with the vertical window

The Unit Configuration bar codes (located on pages 3 and 4 of this

addendum guide) require the scale security seal to be broken.

If the scale security seal is broken, it must be sealed and certified by local

Weights and Measures authorities after the scale calibration process has been

completed. The scanner/scale cannot be placed in service until it is sealed and

certified by the proper authorities.

For further details on calibration procedures for Weights and Measures

certification, refer to the Scale Operation: Calibration section of the Stratos

Installation and User’s Guide.

The certification of the weighing mechanism of the scale version of

this scanner is subject to federal, state and local Weights and

Measures statutes and regulations and can only be performed by

authorized government agencies and/or their duly registered

agents. Each time the scale or weighing mechanism is calibrated,

it should be properly sealed with a paper seal or a wire seal prior to

being placed into service in commerce.

It is the responsibility of the owner of the scale to confirm

compliance with the relevant Weights and Measures statutes and

regulations applicable in your area by checking with the appropriate

government agency before placing a newly calibrated unit into

service or removing any official seals.

IMPORTANT NOTES -BEFORE YOU START

Important Bar Codes

Scale Save Data Bar Code.

The Scale Save Data bar code must be scanned last to “save” the changes in the

scale’s memory. The scale will then reset and begin normal operation. This is

required only for scale configuration items – not for calibration.

Scale Save Data

³996045

Scale Type Bar Code.

The Stratos scanner should have been already programmed to recognize the

type K Diva scale. If, for any reason, the scanner’s non-volatile memory is lost,

the following bar code must be scanned to reprogram the scanner for the

type K Diva scale.

Type K Diva Scale

³446510

SCALE/LOAD CELL CONFIGURATION BAR CODES

Single or Dual Cable Scale Configuration Bar Codes

Unit Configuration (Pounds)

For Kilogram weight units see page 4.

The following bar codes can be used to configure a Single or

Dual Cable MS2xx0.

If the MS2xx0 is currently in a Dual Cable configuration, temporarily

disconnect the Scale to Host cable prior to configuring the scale.

The MS2xx0 must be in scale service mode to use these

bar codes.

Pounds Calibration

³996042

Set the scale measuring range from

0.00 to 30.00 pounds.

SCALE/LOAD CELL CONFIGURATION BAR CODES

Single or Dual Cable Scale Configuration Bar Codes

Unit Configuration (Kilograms)

For Pound weight units see page 3.

The following bar codes can be used to configure a Single or

Dual Cable MS2xx0.

If the MS2xx0 is currently in a Dual Cable configuration, temporarily

disconnect the Scale to Host cable prior to configuring the scale.

The MS2xx0 must be in scale service mode to use these

bar codes.

Kilograms Calibration

³996044

Set the scale measuring range from

0.000 to 15.000 kilograms.

SCALE CONFIGURATION BAR CODES

Single or Dual Cable Scale Configuration Bar Codes

Pole Display Configuration

The following bar codes can be used to configure a Single or

Dual Cable MS2xx0.

If the MS2xx0 is currently in a Dual Cable configuration, temporarily

disconnect the Scale to Host cable prior to configuring the scale.

The MS2xx0 does not need to be in scale service mode.

The Scale Save Data bar code must be scanned last to save the

changed configuration (see page 2).

Scale Display

Single-Line Weight Only

³996003

Set the scale to use a single-line weight only

display to show all scale activity.

The single-line display must be plugged into

the Scale to Display connector on the

MS2xx0 (see Figure 1).

Figure 1. Location of Scale to Display Connector

Scale Display

4-line Price Computing

³996009

Set the scale to use a 4-line price computing

display to show all scale activity.

The 4-line display must be plugged into the

Scale to Display connector on the MS2xx0

(see Figure 1).

Inhaltsverzeichnis

Andere Metrologic Barcode-Lesegerät Handbücher

Metrologic

Metrologic Tire and Rubber Benutzerhandbuch

Metrologic

Metrologic 160 Benutzerhandbuch

Metrologic

Metrologic MS7120 Series Bedienungsanleitung

Metrologic

Metrologic MS860i Mini-Slot Bedienungsanleitung

Metrologic

Metrologic Stratos MS2xxx Series Montage- und Bedienungsanleitung

Metrologic

Metrologic MS6720 Bedienungsanleitung

Metrologic

Metrologic MS7320 InVista Series Bedienungsanleitung

Metrologic

Metrologic MS7120 Orbit Bedienungsanleitung

Metrologic

Metrologic MH941 Bedienungsanleitung

Metrologic

Metrologic MK5145-31A38 Bedienungsanleitung

Metrologic

Metrologic MS6720 Bedienungsanleitung

Metrologic

Metrologic MS9530 Series Bedienungsanleitung

Metrologic

Metrologic Hand-Held Scanner Bedienungsanleitung

Metrologic

Metrologic IS1000 Series Bedienungsanleitung

Metrologic

Metrologic MK1690-61A38 Bedienungsanleitung

Metrologic

Metrologic MS7600 Bedienungsanleitung

Metrologic

Metrologic MK5145-31A38 Bedienungsanleitung

Metrologic

Metrologic StratosE MS2122 Bedienungsanleitung

Metrologic

Metrologic StratosS MS2220 Bedienungsanleitung

Metrologic

Metrologic Cubit MS6520 Series Bedienungsanleitung

Metrologic

Metrologic MS1890 Focus Bedienungsanleitung

Metrologic

Metrologic MS9530 Series Bedienungsanleitung

Metrologic

Metrologic MK3780-31A62 Bedienungsanleitung

Metrologic

Metrologic MS6130 Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung