MikroTik BaseBox 2 Bedienungsanleitung
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
BaseBox-series
BaseBox 2(RB912UAG-2HPnD-OUT), BaseBox 5(RB912UAG-5HPnD-OUT), BaseBox 6 (RB912UAG-6HPnD-This User Manual covers BaseBox models:
OUT).
The Basebox is a solid and weatherproof outdoor device based on the RB912 wireless router model. It has high power wireless and one Gigabit Ethernet
connector, which supports MDI-X auto-detection. The device has two RPSMA connectors for connecting external antennas. The device is packaged with a
power adapter, a PoE injector, and two mounting loops. Extra places for more RP-SMA connectors are available on the unit in this case.
Safety Warnings
Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing
accidents.
Ultimate disposal of this product should be handled according to all national laws and regulations.
The Installation of the equipment must comply with local and national electrical codes.
This product is intended to be mounted outdoors on a pole. Please read the mounting instructions carefully before beginning installation. Failure to use the
correct hardware and configuration or to follow the correct procedures could result in a hazardous situation for people and damage to the system.
Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.
Read the installation instructions before connecting the system to the power source.
We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your
own risk!
In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.
It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling
requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.
This is a class A device. In a domestic environment, this product might cause radio interference in which case the user might be required to take adequate
measures.
This MikroTik equipment complies with the FCC, IC and European Union radiation exposure limits set forth for an Exposure to Radio Frequency Radiation:
uncontrolled environment.
First use
Choose your powering solution, please see the section for possibilities.Powering
Remove the lid, and connect the antenna to the RP-SMA connectors. Bend the cable with a large radius, so that it will be able to exit through the
cable openings in the bottom of the lid. Put the lid back, with the small arrow to the front of the case.
Open the device bottom door, to reveal the Ethernet connector.
Connect your direct input power jack if not using POE, to start up the device.
Connect your Ethernet cable to the Gigabit Ethernet port.
The device will boot up and after a short beep Wireless network will be available for connecting.
Open network connections on your pc, mobile phone, or other device and search for MikroTik wireless network and connect to it.
Once connected to the wireless network, open configuration, since there is no password by https://192.168.88.1 in your web browser to start
default, you will be logged in automatically.
We recommend clicking the "Check for updates" button and updating your RouterOS software to the latest version to ensure the best
performance and stability.
Choose your country, to apply country regulation settings, and set up your password on the screen that loads.
Mounting
The device can be mounted in several ways: wall, ceiling, pole. To tighten the device to a pole, use the provided metal hose clamp.
Guide the loop around the device through the provided holes, and around the pole where it will be mounted, or use a DIN mount to attach the device to a
rail:
You should avoid connecting a loose Ethernet cable to the Ethernet port, secure the cable to a wall or the pole, so that the cable weight is not pulling the
port. It is recommended to secure the Ethernet cable less than 2m from the device. This is to ensure that the cable doesn't damage the port by its weight,
or doesn't fall out. It is possible to connect grounding wires to the PCB board mounting holes, but to do this, you must remove the PCB from the case.
Powering
The device accepts power from the power jack or from the Ethernet port:
Direct-input power jack (5.5mm outside and 2mm inside, female, pin positive plug) accepts 24 V DC.
Ethernet port accepts passive Power over Ethernet 18-57 V DC (Please compensate voltage for loss due to cable length)
The power consumption under maximum load can reach 12 W. For BaseBox 6 model up to 23 W.
Configuration
RouterOS includes many configuration options in addition to what is described in this document. We suggest
starting here to get yourself accustomed to the possibilities: . In case IP connection is not available,https://mt.lv/help
the Winbox tool ( ) can be used to connect to the MAC address of the device from the LAN sidehttps://mt.lv/winbox
(all access is blocked from the Internet port by default).
For recovery purposes, it is possible to boot the device from the network, see a section .Reset button
Expansion Slots and Ports
BaseBox 2 model - 2.4 GHz, 802.11b/g/n.
BaseBox 5 model - 5 GHz, 802.11a/n.
BaseBox 6 model - 6 GHz, 802.11a/n.
One 10/100/1000 Gigabit Ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X), so you can use either straight or
crossover cable for connecting to other network devices.
USB type-A slot.
One miniPCIe slot.
This device might be incompatible with the R11e-LTE international modem.
The miniPCI-e slot usage
Warning! This equipment should be installed and operated with a minimum distance of 380 cm between the device and your body. Operation of
this equipment in the residential environment could cause radio interference.
1.
2.
3.
4.
5.
6.
Remove top cover;
Unscrew two screws on the back of the device;
Open Ethernet port cover and withdraw it from the base of the device;
Unscrew the antenna connector;
Withdraw the PCB plate from the base cover;
Install your modem and reassemble.
Reset button
The reset button has three functions:
Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS configuration (total 5 seconds).
Keep holding for 5 more seconds, LED turns solid, release now to turn on CAP mode. The device will now look for a CAPsMAN server (total 10
seconds).
Or Keep holding the button for 5 more seconds until LED turns off, then release it to make the RouterBOARD look for Netinstall servers (total 15
seconds).
Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device.
Useful for RouterBOOT debugging and recovery.
Operating system support
The device supports RouterOS software version 6. The specific factory-installed version number is indicated in the RouterOS menu /system resource.
Other operating systems have not been tested.
Included parts
*DIN mount includes four screws to attach it to the back of the device.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a commercial installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its
antenna must not be co-located or operation in conjunction with any other antenna or transmitter.
IMPORTANT: Exposure to Radio Frequency Radiation.
This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance between the radiator and any part of your body, please see the table below.
Model FCC ID RF Exposure minimum safety distance
BaseBox 2 TV7RB912G-2HPND 142 cm
BaseBox 5 TV7RB912G-5HPNDM 375 cm
BaseBox 6 TV7RB912G-6HPND 375 cm
To avoid pollution of the environment, please separate the device from household waste and dispose of it in a safe manner, such as in
designated waste disposal sites. Familiarize yourself with the procedures for the proper transportation of the equipment to the designated
disposal sites in your area.
Innovation, Science and Economic Development Canada
This device complies with Industry Canada's licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [A] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (A)/NMB-3(A)
IMPORTANT: Exposure to Radio Frequency Radiation.
This equipment complies with the IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated
with a minimum distance between the radiator and any part of your body please see table below.
Cet équipement est conforme aux limites d'exposition au rayonnement IC définies pour un environnement non contrôlé. Cet équipement doit être installé et
utilisé avec une distance minimale entre le radiateur et toute partie de votre corps, voir le tableau ci-dessous.
Model IC RF Exposure minimum safety distance
BaseBox 2 7442A-912G2HPND 142 cm
BaseBox 5 7442A-912G5HPNDM 378 cm
BaseBox 6 7442A-912G6HPNDM 378 cm
UKCA marking
Eurasian Conformity Mark
Частотный диапазон Мощность передатчика
2400-2483.5МГц, 5150-5350 МГц, 5650-5850 МГц, 6425-7100 МГц ≤100 мВт
*Доступные частотные каналы могут различаться в зависимости от модели продукта и сертификации.
Информация о дате изготовления устройства указана в конце серийного номера на его наклейке через дробь. Первая цифра означает номер
года (последняя цифра года), две последующие означают номер недели.
Изготовитель: Mikrotikls SIA, Aizkraukles iela 23, Riga, LV-1006, Латвия, [email protected]. Сделано в Китае, Латвии или Литве. Cм. на
упаковке.
Для получения подробных сведений о гарантийном обслуживании обратитесь к продавцу. Информация об импортерах продукции MikroTik в
Российскую Федерацию: https://mikrotik.com/buy/europe/russia
Продукты MikroTik, которые поставляются в Евразийский таможенный союз, оцениваются с учетом соответствующих требований и помечены
знаком EAC, как показано ниже:
Norma Oficial Mexicana
Rango de frecuencia (potencia de salida máxima): Los canales de frecuencia 2400-2483.5 MHz (30 dBm), 5725-5850 MHz (30 dBm).
disponibles pueden variar según el modelo y la certificación del producto.
EFICIENCIA ENERGETICA CUMPLE CON LA NOM-029-ENER-2017.
La operacion de este equipo esta sujeta a las siguientes dos condiciones:
Es posible que este equipo o dispositivo no cause interferencia perjudicial y.
Este equipo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacion no deseada.
Fabricante: Mikrotikls SIA, Brivibas gatve 214i, Riga, LV-1039, Latvia.
País De Origen: Letonia; Lituania; China (Republica Popular); Estados Unidos De America; Mexico.
Por favor contacte a su distribuidor local para preguntas regionales específicas. La lista de importadores se puede encontrar en nuestra página de inicio –
https://mikrotik.com/buy/latinamerica/mexico.
The National Commission for the State Regulation of Communications and
Informatization by Ukraine
Виробник: Mikrotikls SIA, Brivibas gatve 214i Рига, Латвія, LV1039.
Робоча частота (Максимальна вихідна потужність): 5150-5250 МГц (23 дБм), 5250-5350 МГц (20 дБм), 5470-5725 МГц (27 дБм).
CE Declaration of Conformity
Manufacturer: Mikrotikls SIA, Brivibas gatve 214i Riga, Latvia, LV1039.
Hereby, Mikrotīkls SIA declares that the radio equipment type RouterBOARD is in compliance with Directive 2014/53/EU. The full text of the EU declaration
of conformity is available at the following internet address: https://mikrotik.com/products
Frequency bands terms of use
Frequency range (for applicable models) Channels used Maximum Output Power (EIRP) Restriction
2412-2472 MHz 1 - 13 20 dBm Without any restriction to use in all EU Member States
5150-5250 MHz 26 - 48 23 dBm Restricted to indoor use only*
5250-5350 MHz 52 - 64 20 dBm Restricted to indoor use only*
5470-5725 MHz 100 - 140 27 dBm Without any restriction to use in all EU Member States
* It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling
requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed!
Справжнім Mikrotikls SIA заявляє, що маршрутизатор відповідає основним вимогам та іншим відповідним положенням директиви 2014
/53/EC, а також суттєвим вимогам Технічного регламенту радіообладнання, затвердженого постановою Кабінету Міністрів України від
24 травня 2017 року № 355.
Для експлуатації в Україні необхідно отримати дозвіл на експлуатацію у порядку, затвердженому рішенням НКРЗІ від 01.11.2012 № 559,
зареєстрованому в Міністерстві юстиції України 03.01.2013 за № 57/22589.
This MikroTik device meets Maximum WLAN transmit power limits per ETSI regulations. For more detailed information see Declaration of
Conformity above / Dieses MikroTik-Gerät erfüllt die maximalen WLAN- Sendeleistung Grenzwerte gemäß ETSI-Bestimmungen. Weitere
Informationen finden Sie oben unter Konformitätserklärung / Cet appareil MikroTik respecte les limites maximales de puissance de transmission
WLAN conformément aux réglementations ETSI. Pour plus d'informations, voir la déclaration de conformité ci-dessus / Questo dispositivo
MikroTik è conforme ai limiti massimi di potenza di trasmissione WLAN in conformità con le normative ETSI. Per ulteriori informazioni,
consultare la dichiarazione di conformità sopra / Este dispositivo MikroTik cumple con los límites máximos de potencia de transmisión WLAN de
acuerdo con las regulaciones ETSI. Para obtener más información, consulte la declaración de conformidad anterior / Это устройство MikroTik
соответствует максимальным пределам мощности передачи WLAN в соответствии с правилами ETSI. Для получения дополнительной
информации см. Декларацию соответствия выше.
The information contained here is subject to change. Please visit the product page on
www.mikrotik.com for the most up to date version of this
document.
Andere Handbücher für BaseBox 2
2
Dieses Handbuch passt für folgende Modelle
9
Inhaltsverzeichnis
Andere MikroTik Drahtloser Zugangspunkt Handbücher
MikroTik
MikroTik NetMetal ac2 Series Bedienungsanleitung
MikroTik
MikroTik hAP ac Bedienungsanleitung
MikroTik
MikroTik Chateau 5G Bedienungsanleitung
MikroTik
MikroTik BaseBox 2 Bedienungsanleitung
MikroTik
MikroTik RBLDF-5nD Bedienungsanleitung
MikroTik
MikroTik NetMetal 5 triple Bedienungsanleitung
MikroTik
MikroTik cAP lite Bedienungsanleitung
MikroTik
MikroTik RBLHGGR&R11e-LTE6 Bedienungsanleitung
MikroTik
MikroTik wAP 60G Series Bedienungsanleitung
MikroTik
MikroTik PWR-LINE AP Bedienungsanleitung
MikroTik
MikroTik RBcAPGi-5acD2nD-XL Bedienungsanleitung
MikroTik
MikroTik cAP ax Bedienungsanleitung
MikroTik
MikroTik RBcAPL-2nD Bedienungsanleitung
MikroTik
MikroTik Cube 60G Series Bedienungsanleitung
MikroTik
MikroTik LtAP LR8 LTE kit Bedienungsanleitung
MikroTik
MikroTik Audience Bedienungsanleitung
MikroTik
MikroTik cAP Leitfaden
MikroTik
MikroTik hAP ac lite Bedienungsanleitung
MikroTik
MikroTik LHG R Bedienungsanleitung
MikroTik
MikroTik CRS109-8G-1S-2HnD-IN Bedienungsanleitung
Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung
Ubiquiti
Ubiquiti NanoStation NSM2 Bedienungsanleitung
Cisco
Cisco Aironet 1550 Series Bedienungsanleitung
Aruba
Aruba IAP-335 Bedienungsanleitung
Advantek Networks
Advantek Networks AWN-AP-54MR Bedienungsanleitung
IP-COM
IP-COM AP355 Bedienungsanleitung
Buffalo
Buffalo AirStation WLA-L11G Bedienungsanleitung
EnGenius
EnGenius EnStationACv2 Bedienungsanleitung
D-Link
D-Link DAP-3662 Bedienungsanleitung
xG Technology
xG Technology xMax CN1300 Bedienungsanleitung
Widelink
Widelink ezWave WAP-1100 Series Bedienungsanleitung
Edimax
Edimax CAP1200 Bedienungsanleitung
