MiLAN MIL-S8000G Bedienungsanleitung
8-Port Gigabit Switch
MIL-S8000G
User Guide
Eight Auto-negotiation 10/100/1000Mbps Gigabit Ethernet
RJ-45 Ports. Each port with Auto MDI/MDIX.
Regulatory Approval
- FCC Class A
- UL 1950
- CSA C22.2 Number 950
- EN60950
- CE
EN55022 Class A
EN55024
Canadian EMI Notice
This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numerique de la classe A respecte toutes les exigences du Reglement sur le materiel
brouilleur du Canada.
European Notice
Products with the CE marking comply with both the EMC Directive (89/336EEC) and the Low Voltage
Directive (73/23EEC) issued by the commisions of the European Community. Compliance with these
directives implies conformity to the following European norms:
- EN55022 (CISPR 22) - Radio Frequency Interference
- EN61000-X - Electromagnetic Immunity
- EN60950 (IEC950) - Product Safety
Five-Year Limited Warranty
MiLAN Technology warrants to the original consumer or purchaser that each of its product and component thereof,
will be free from defects in material and/or workmanship for a period of five years from the original factory shipment
date. Any warranty hereunder is extended to the original consumer or purchaser and is not assignable.
MiLAN Technology makes no express or implied warranties including, but not limited to, any implied warranty of
merchantability or fitness for a particular purpose, except as expressly set forth in this warranty. In no event shall
MiLAN Technology be liable for incidental or consequential damages, costs, or expenses arising out of or in
connection with the performance of the product delivered hereunder. MiLAN Technology will in no case cover
damages arising out of the product being used in a negligent fashion or manner.
Trademarks
© 2003 MiLAN, the MiLAN logo and MiLAN Technology are either trademarks or registered
trademarks of MiLAN Technology in the United States and/or other countries.
To Contact MiLAN Technology
For prompt response when calling for service information, have the following information ready:
- Product serial number and revision
- Date of purchase
- Vendor or place of purchase
You can reach MiLAN Technology technical support at:
- E-mail: support@milan.com
- Telephone: +1.408.744.2751
- Fax: +1.408.744.2771
MiLAN Technology
1329 Moffett Park Drive
Sunnyvale, CA 94089
United States of America
Telephone: +1.408.744.2775
Fax: +1.408.744.2793
http://www.milan.com
P/N 90000404_A
1
Table of Contents
1. Introduction
Features
Package Contents
2. Hardware Description
Front Panel
LED Indicators
Rear Panel
3. Installation
Desktop Installation
Rack-mount Installation
Power On
4. Network Application
Backbone Switch
5. Network Configuration
Login to the Console Interface
5.1 Port Status
5.2 Port Configuration
5.3 Mirror Configuration
5.4 VLAN Configuration
5.5 VLAN Setup
5.6 Trunk Configuration
5.7 Miscellaneous Configuration
6. Troubleshooting
7. MIL-S8000G Technical Specifications
2
1. Introduction
Gigabit Ethernet over copper technology is a cost-effective way for
network equipment to be upgraded from Fast Ethernet to Gigabit speeds
without the use of expensive fiber optics cabling. Gigabit networks create
high-speed backbone connections between switches, servers, databases
and end stations.
The MIL-S8000G, an 8-Port Gigabit switch, is an ideal solution for solving
traffic block at the core of the network. It offers eight auto-negotiation
10/100/1000Base-T Gigabit Ethernet ports that can significantly improve
your network’s backbone performance. The switch will fit into any level
network to act as an exit to the backbone switch that can handle
throughput speeds up to 2000Mbps at Full-duplex mode.
Figure 1-1. MIL-S8000G
The switch will automatically detect the speed of the device that you plug
into it to allow connections to 10, 100 or 1000Mbps devices.
The eight port Gigabit switch features automatic MDI/MDIX connections
for each port. It also features store-and-forward switching and auto-
learning of source addresses with an 8,000 entry MAC address table.
Features
Conforms to IEEE 802.3, 802.3u, 802.3ab and 802.3x standards
Eight auto-negotiation 10/100/1000Base-TX switch ports (Using
shielded RJ-45 connections)
Automatic MDI/MDIX crossover for all ports
Embedded 8K entry MAC address table (Supports 8K
Unicast/Multicast/Broadcast addresses)
Store-and-Forward architecture
Full Duplex and Half Duplex flow control support
Plug-and-Play configuration
LED Indicators for Power, 100M, 1000M, LK/ACT, and FDX/COL
Standard 19-inch rackmount design
Console Management (Port Configuration/Statistics, Port Mirroring,
Port-Based VLAN’s and Port Trunking)
3
Package Contents
MIL-S8000G 8 port Gigabit switch
Power Cord
Four Adhesive Rubber Feet
User’s Manual
Warranty Card
Compare the contents of your MIL-S8000G package with the
standard checklist above. If any item is missing or damaged, please
contact your local dealer for service.
4
2. Hardware Description
Front Panel
The Front Panel of the 8-Port Gigabit Switch consists of eight auto-
negotiation 10/100/1000Mbps Ethernet RJ-45 connectors, supporting
automatic MDI/MDIX, and four LED-indicators (1000M, 100M, LK/ACT,
FUL/COL) for each Gigabit port.
Figure 2-1. The Front Panel of the 8-Port Gigabit Switch
RJ-45 Ports ( Auto MDI/MDIX ): Eight auto-negotiation
10/100/1000Mbps Ethernet RJ-45 connectors.
Console Port : Console management is available through the
Console Port. A direct connection between the Switch and an end
station ( PC ) via a RS-232 cable is required.
LED Indicators
The LED Indicators gives a real-time indication of system operating
statuses. There are four LED-indicators for each Gigabit port and one
Power LED for Unit. The following table provides descriptions of LEDs
status and their meaning.
Figure 2-2.
LED Indicators.
Console Port
LEDs
RJ-45 Gigabit Ports
5
LED Status Description
Green Power On
Power
Off Power is not connected
Green The port is operating at the speed of 1000Mbps.
1000M
Off No device attached or in 10/100Mbps mode
Green The port is operating at the speed of 100Mbps.
100M
Off No device attached or in 10Mbps mode
Green The port is connecting with the device.
Blinks The port is receiving or transmitting data.LK/ACT
Off No device attached.
Yellow The port is operating in Full Duplex mode.
FD
Off No device attached or in Half Duplex mode.
Table 2-1. Descriptions of LED Indicators
Rear Panel
The 3-pronged power plug and ventilation fan are located at the rear
panel. The switch will work with AC in the range 100-240V AC, 50-60Hz.
The rear panel of the MIL-S8000G Gigabit switch is shown below.
Figure 2-3. The Rear Panel of the MIL-S8000G Switch
6
3. Installation
Desktop Installation
Set the switch on a sufficiently large flat space with a power outlet nearby.
The surface should be clean, smooth, level, and sturdy.
Make sure there is enough clearance around the switch to allow
attachment of cables, power cord and air circulation.
Attaching Rubber Feet
A. Make sure mounting surface on the bottom of the switch is grease
and dust free.
B. Remove adhesive backing from the rubber feet.
Figure 3-1. Attaching rubber feet to each corner on the bottom of the
Switch
C. Apply the rubber feet to each corner on the bottom of the switch.
These footpads can prevent the switch from shock/vibration.
Rack-mounted Installation
The MIL-S8000G includes a rack-mounted kit that allows it to be mounted
in an EIA standard size, 19-inch Rack.
Perform the following steps to rack mount the switch:
A. Position one bracket to align with the holes on one side of the switch
and secure it with the smaller bracket screws. Then attach the
remaining bracket to the other side of the switch.
7
Figure 3-2. Attach mounting brackets with screws
B. After attaching both mounting brackets, position the MIL-S8000G
switch in the rack by lining up the holes in the brackets with the
appropriate holes on the rack. Secure the switch to the rack with a
screwdriver and the rack-mounting screws.
Figure 3-3. Mounting the MIL-S8000G in an EIA standard 19-inch Rack
Note: For proper ventilation, allow at least 4 inches (10 cm) of clearance
on the front and 3.4 inches (8 cm) on the back of the switch. This is
especially important for enclosed rack installation.
Power On
Connect the power cord to the power socket on the rear panel of the
switch. The other side of power cord connects to the power outlet. The
internal power supply in the Switch works with AC in the voltage range
100-240VAC, frequency 50~60Hz.
Check the power indicator on the front panel to see if power is properly
supplied.
8
4. Network Application
The MIL-S8000G Switch can be used connect servers, switches,
workstations, and PCs (a Gigabit 1000Base-T NIC is required for PC
installation) to each other by connecting these devices directly to the
Switch. The Switch automatically learns node addresses, which are used
to filter and forward all traffic, based on the destination address.
Backbone Switch
The MIL-S8000G Switch is an ideal solution for enterprise networks
where large data broadcasts are constantly processed.
All ports can be connected to departmental switches, and the
departmental switches can be connected to the MIL-S8000G Switch.
Each end station can access the server’s data by connecting the servers
to the core switch. This will allow all the devices in the network to
communicate with each other.
Inhaltsverzeichnis
Andere MiLAN Schalten Handbücher
MiLAN
MiLAN MIL-SME801P Bedienungsanleitung
MiLAN
MiLAN MIL-SM4004TG Bedienungsanleitung
MiLAN
MiLAN MIL-SM2401M Bedienungsanleitung
MiLAN
MiLAN MIL-SM801 Bedienungsanleitung
MiLAN
MiLAN MIL-S2612 Bedienungsanleitung
MiLAN
MiLAN MicroHub LE MIL-4000H Bedienungsanleitung
MiLAN
MiLAN MIL-SM24T4DPA Programmierhandbuch
MiLAN
MiLAN MIL-S800 Bedienungsanleitung
MiLAN
MiLAN MIL-SM801XX Bedienungsanleitung
MiLAN
MiLAN MIL-S3580 Bedienungsanleitung
MiLAN
MiLAN MIL-SM2401MAF Bedienungsanleitung
MiLAN
MiLAN MIL-S800I Bedienungsanleitung
MiLAN
MiLAN MIL-S5000T Bedienungsanleitung
MiLAN
MiLAN MIL-SM801P Bedienungsanleitung
MiLAN
MiLAN MIL-S801XX Bedienungsanleitung
MiLAN
MiLAN MIL-SM800 Bedienungsanleitung
MiLAN
MiLAN mil-s2400s Bedienungsanleitung
MiLAN
MiLAN MIL-S500 Bedienungsanleitung
MiLAN
MiLAN MIL-H1120 Bedienungsanleitung
MiLAN
MiLAN MIL-S24T2GPA Bedienungsanleitung
Beliebte Schalten Handbücher anderer Marken
MicroNet
MicroNet SP1200A Bedienungsanleitung
Ruijie
Ruijie RG-PF2920 Series Installations- und Betriebsanleitung
Altinex
Altinex DA1914SX Bedienungsanleitung
RJM
RJM MASTERMIND PBC/6X Bedienungsanleitung
Atlas
Atlas MMK-KVM8 Bedienungsanleitung
Cabletron Systems
Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung