MiLAN MIL-S800 Bedienungsanleitung

MIL-S800 User’s Guide

8 port 10/100BASE-TX Switch

Regulatory Approval

- FCC ClassA

- UL 1950

- CSA C22.2 No. 950

- EN60950

- CE

- EN55022 Class B

- EN55024

Canadian EMI Notice

This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numerique de la classe A respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada.

European Notice

Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the

Commission of the European Community Compliance with these directives imply conformity to the following European Norms:

- EN55022 (CISPR 22) - Radio Frequency Interference

- EN61000-X - Electromagnetic Immunity

- EN60950 (IEC950) - Product Safety

Five-Year Limited Warranty

MiLAN Technology warrants to the original consumer or purchaser that each of it's products, and

all components thereof, will be free from defects in material and/or workmanship for a

period of five years from the original factory shipment date. Any warranty hereunder is

extended to the original consumer or purchaser and is not assignable.

MiLAN Technology makes no express or implied warranties including, but not limited to, any

implied warranty of merchantability or fitness for a particular purpose, except as expressly set

forth in this warranty. In no event shall MiLAN Technology be liable for incidental or

consequential damages, costs, or expenses arising out of or in connection with the

performance of the product delivered hereunder. MiLAN Technology will in no case cover damages

arising out of the product being used in a negligent fashion or manner.

Trademarks

The MiLAN logo and MiLAN Technology trademarks are registered trademarks ofof MiLAN Technology

in the United States and/or other countries.

To Contact MiLAN Technology

For prompt response when calling for service information, have the following information ready:

- Product serial number and revision

- Date of purchase

- Vendor or place of purchase

You can reach MiLAN Technology technical support at:

E-mail: [email protected]

Telephone: +1.408.744.2751

Fax: +1.408.744.2771

MiLAN Technology

1329 Moffett Park Drive

Sunnyvale, CA 94089

United States of America

Telephone: +1.408.744.2775

Fax: +1.408.744.2793

http://www.milan.com

info @ milan.com

P/N: 90000377_F

Table of Contents

Chapter1.Introduction Pg 1

1-1 General Description……………………………………. Pg. 1

1-2 Key Features……………………………………………… Pg. 1

1-3 Package Contents……………………………………… Pg. 2

1-4 Hardware Description………………………………….. Pg. 3

Chapter 2. Hardware Installation Pg 4

2-1 Quick Installation………………………………………... Pg. 4

2-2 LED Descriptions…………………………………………. Pg. 5

Chapter 3. Network Application Pg 6

3-1 Stand Alone……………………………………………… Pg. 6

3-2 Uplink Multiple Hubs……………………………………. Pg. 6

Chapter 4. Trouble Shooting Pg 7

Chapter 5. Product Specifications Pg 8

5-1 General Specification………………………………….. Pg. 8

5-2 Performance Specification Pg. 8

5-3 Physical & Environmental Specification……………..…. Pg. 8

Chapter 1 Introduction

1-1 General Description

The MIL-S800 switch provides eight auto-sensing 10/100Mbps RJ45 Ethernet ports. This high performance,

low cost, wire speed desktop switch is ideal for any network where 8 ports are needed, for a solution to an

enterprise need or for a home network. The MIL-S800 can be mounted on the wall with keyholes in the

chassis or magnetically attached to any metal surface.

1-2 Key Features

•Compliant with IEEE 802.3, 802.3u & 802.3x standards

•8 Auto-sensing RJ-45 ports for 10BASE-T or 100 BASE-TX connections

•Embedded 2K entry MAC address table

•512KB memory buffer sharing

•Store-and-Forward operation support

•Full duplex and half duplex flow control

•Plug-and-Play configuration auto addresses learning

•LED indicators for power, link speed 100Mbps, link and activity, full duplex and collision

•Space-saving compact size

•Wall or desktop mountable

•Magnets provide installation on any metal surface

•Auto MDI/MDIX

1-3 Package Contents

Your package contents should include the following parts:

•One 8-port Auto-sensing switching Hub

•One DC power adapter

•This User’s Guide

•Four rubber feet with adhesive pads

•Two magnets

•Warranty card

Figure 1. Package contents

1-4 Hardware Description

The Front Panel

The front panel contains power and LED Indicators.

Figure 2. Front panel view of the MIL-S800

Front panel LED Indicators

Per Device Power

100M (Link on 100Mbps)

LNK/ACT (Link/Activity)

Per Port FDX/COL (Full Duplex/Collision)

For LED details, please refer to Chapter 2, LED Descriptions.

The Rear Panel

The rear panel of the MIL-S800 consists of a DC power connector and 8 auto-sensing ports.

Figure 3. Rear panel view of the MIL-S800

·Eight Auto-sensing RJ-45 ports for 10BASE-T or 100 BASE-TX connections.

·Auto MDI/MDIX: Detects the straight cable connection, NIC or cascade to a hub or switch, without

changing the cable.

·DC Power Connector.

Chapter 2 Hardware Installation

2-1 Quick Installation

•The MIL-S800 should be placed in a well-ventilated room with proper temperature and humidity.

•Do not place the unit near water.

•The maximum distance between the port to the standard network interface is 100 meters.

•For desktop installation, ensure the surface is clean, smooth, level and sturdy. Apply self-adhesive rubber

feet to the bottom of the switch near the corners.

•For wall installation, place two screws securely into the wall. Slide the cross recesses on the bottom of the

MIL-S800 onto the screws.

•For mounting the MIL-S800 on a metal surface, install magnets as shown in instructions and apply to

surface.

•Visually check that the power cord is not damaged. Plug the female end of the cord into the rear of the

MIL-S800 and the male end (power converter) into a power outlet.

•Do not plug a phone jack connector into any RJ-45 port. This may cause damage. Use only twisted-pair

cables with RJ-45 connectors that conform to FCC standards.

Figure 4. Installation of switch

2-2 LED Descriptions

Figure 5. Front panel view of LED indicators

The following table lists the LEDs and their function.

Chapter 3 Network Application

3-1 Stand Alone

The application of a simple standalone switch is illustrated below. The maximum distance between the switch

and the workstation is 100 meters.

Figure 6. The switch as a backbone for a small 10/100BASE-TX network

3-2 Network

You can cascade the MIL-S800 to another hub or a switch without using a crossover cable.

ure 7. Small Network Confi

uration

Chapter 4 Troubleshooting

•Power

If the power indicator is not on after the power cord is plugged in, check the power outlet or power cord. If

you lose power after the switch has been operating for some time, check for loose power connections,

power losses or surges at the power outlet. Disconnect and reconnect the power. If the problem persists,

contact MiLAN Technical Support.

•Cabling

Verify that the cabling type is correct. Be sure all cable connectors are securely seated in the required

ports. Use standard unshielded twisted-pair (UTP), Category 3, 4, or 5 cables. Use only Category 5

when there is a Fast Ethernet connection. Make sure the distance between the MIL-S800 and the

workstation, is less than 100 meters.

Inhaltsverzeichnis

Andere MiLAN Schalten Handbücher

MiLAN

MiLAN MIL-SM24T4DPA Programmierhandbuch

MiLAN

MiLAN MIL-H1120 Bedienungsanleitung

MiLAN

MiLAN MIL-S801XX Bedienungsanleitung

MiLAN

MiLAN MIL-SM8TAF1GPA Programmierhandbuch

MiLAN

MiLAN MIL-SM802GAF Bedienungsanleitung

MiLAN

MiLAN MIL-S3580 Bedienungsanleitung

MiLAN

MiLAN MIL-S8001TG Bedienungsanleitung

MiLAN

MiLAN MIL-SM800P Bedienungsanleitung

MiLAN

MiLAN MIL-SM4004TG Bedienungsanleitung

MiLAN

MiLAN MIL-S24000T Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

MiLAN

MiLAN MIL-S800I Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

MiLAN

MiLAN MIL-S2612 Bedienungsanleitung

MiLAN

MiLAN MIL-SM24004TG Bedienungsanleitung

MiLAN

MiLAN MIL-S8000G Bedienungsanleitung

MiLAN

MiLAN MIL-SM801 Bedienungsanleitung

MiLAN

MiLAN MIL-S3570 Bedienungsanleitung

MiLAN

MiLAN MIL-SM24004TG Bedienungsanleitung

MiLAN

MiLAN MIL-SM801P Bedienungsanleitung

MiLAN

MiLAN MIL-SME801GSX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401MAF Bedienungsanleitung

MiLAN

MiLAN MIL-SM4804G Bedienungsanleitung

MiLAN

MiLAN MIL-SM801XX Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung