Milwaukee MC510 Bedienungsanleitung

SPECIFICATIONS: MC510

RANGE ±1000 mV

RESOLUTION 1 mV

ACCURACY (@25°C) ±5 mV

SETPOINT 0 to 600 mV

ALARM active when the measure is

lower/higher than setpoint

depending on user selection

OUTPUT POWER SOCKET active when the measure is

higher/lower than selected setpoint

(5A max) depending on user selection

ORP ELECTRODE MA921B/2 (included)

ENVIRONMENT 0 to 50°C, 95% RH max.

POWER SUPPLY 12 VDC (included)

POWER DRIVERS 2A, 60Hz or 230VAC, 1A, 50Hz

DIMENSIONS 148.5 x 82.5 x 32 mm

WEIGHT 180 g (meter only)

OPTIONAL ACCESSORIES:

MA921B/2 ORP Electrode with BNC connector and 2m cable

M10000B Electrode rinse solution, 20 mL sachet (25 pcs)

MA9015 Electrode storage solution, 220 mL bottle

WARRANTY:

This instrument is warranted from all defects in materials and manufacturing for a period of two

years from the date of purchase. The electrode is warranted for a period of 6 months.

If during this period, the repair or replacement of parts is required, where the damage is not due to

negligence or erroneous operation by the user, please return the parts to either dealer or our office

and the repair will be effected free of charge

Note: We reserve the right to modify the design, construction and appearance of our products

without advance notice.

USER MANUAL

PORTABLE

ORP METER

MODEL: MC510

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com

OPERATION:

•Connect the supplied 12

VDC power adapter to the

meter and to the mains line.

•Connect the ORP electrode

to the BNC socket on the

bottom of the meter.

•Always remove the elec-

trode protective cap before

taking any measurement. If

the electrode has been left

dry, soak the tip (bottom 2.5

cm) in rinse solution

(M10000B) for a few minutes to reactivate it.

•Turn the instrument on by pressing the ON/OFF key.

•Allow the reading to stabilize and the meter will start continuous

monitoring.

•The meter is factory calibrated.

•A blinking alarm will indicate when the measured ORP value is lower or

higher than the setpoint, depending on user selection.

NOTE:

•The power contact is not protected by fuse inside the meter. It is

recommended to protect it outside, against failure.

•WARNING: when the alarm led is blinking, the mains voltage is

present in the output power socket.

SETPOINT:

•The setpoint can be selected by

adjusting the central front knob to the

desired value.

•The selectable range for MC510 is

from 0 to 600 mV.

•The nature of the setpoint can be selected by setting the switch to the

desired position (ABOVE or BELOW).

INSTALLATION PROCEDURE:

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com

Andere Milwaukee Messgerät Handbücher

Milwaukee

Milwaukee MW802 Bedienungsanleitung

Milwaukee

Milwaukee C 12 IC AVD Bedienungsanleitung

Milwaukee

Milwaukee SM101 Bedienungsanleitung

Milwaukee

Milwaukee MW11 Bedienungsanleitung

Milwaukee

Milwaukee PH55 Bedienungsanleitung

Milwaukee

Milwaukee MI806 Bedienungsanleitung

Milwaukee

Milwaukee 3712 Bedienungsanleitung

Milwaukee

Milwaukee REDLITHIUM Bedienungsanleitung

Milwaukee

Milwaukee 48-22-5112 Bedienungsanleitung

Milwaukee

Milwaukee MI 404 Bedienungsanleitung

Milwaukee

Milwaukee MW12 Bedienungsanleitung

Milwaukee

Milwaukee pH54 Bedienungsanleitung

Milwaukee

Milwaukee MW190 Bedienungsanleitung

Milwaukee

Milwaukee M12 3PL Bedienungsanleitung

Milwaukee

Milwaukee MI404 Bedienungsanleitung

Milwaukee

Milwaukee M12 SPL Bedienungsanleitung

Milwaukee

Milwaukee M12 SUB-SCANNER 2291-20 Bedienungsanleitung

Milwaukee

Milwaukee MW11 Bedienungsanleitung

Milwaukee

Milwaukee MA871 Bedienungsanleitung

Milwaukee

Milwaukee Mi170 Bedienungsanleitung

Milwaukee

Milwaukee pH 58 Bedienungsanleitung

Milwaukee

Milwaukee MI 404 Bedienungsanleitung

Milwaukee

Milwaukee MW500 Bedienungsanleitung

Milwaukee

Milwaukee MW170 MAX Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung