Milwaukee Smart Monitoring System SMS110 Bedienungsanleitung

Milwauke

USER MANUAL

PORTABLE pH METER

MODELS: SMS110 - SMS120 - SMS122

Smart Monitoring System

ISMIL110R1 03/03

SPECIFICATIONS:

SMS110 SMS120 SMS122

RANGE 0.0 to 14.0 pH

RESOLUTION 0.1 pH

ACCURACY (@25°C) ±0.2 pH

SETPOINT 3.5 to 7.5 pH 5.5 to 9.5 pH

ALARM active when measure is

higher than selected setpoint

OUTPUT POWER SOCKET active when measure is

(for SMS122 only) higher than selected setpoint (5A max)

POWER DRIVERS 115VAC, 2A, 60Hz or 230VAC, 1A, 50Hz

(for SMS122 only)

pH ELECTRODE MA911B/2 (included)

ENVIRONMENT 0 to 50°C, 95% RH not condensing

POWER SUPPLY 12 VDC (included)

DIMENSIONS 160 x 80 x 40 mm

WEIGHT 220 g (meter only)

OPTIONAL ACCESSORIES:

M10004B pH 4.01 buffer solution, 20 ml sachet (25 pcs)

M10007B pH 7.01 buffer solution, 20 ml sachet (25 pcs)

M10010B pH 10.01 buffer solution, 20 ml sachet (25 pcs)

M10000B Electrode rinse solution, 20 ml sachet (25 pcs)

MA9015 Electrode storage solution, 20 ml sachet (25 pcs)

WARRANTY:

These instruments are warranted from all defects in materials and manufac-

turing for a period of two years from the date of purchase. The electrode is

warranted for a period of 6 months.

If during this period, the repair or replacement of parts is required, where the

damage is not due to negligence or erroneous operation by the user, please

return the parts to either dealer or our office and the repair will be effected

free of charge.

Note: We reserve the right to modify the design, construction and appearance of our prod-

ucts without advance notice.

Milwauke

OPERATION:

• Connect the supplied 12VDC

power adapter to the meter and

to the mains line.

• Connect the pH-electrode to the

BNC socket on the bottom of

the meter.

• Always remove the electrode

protective cap before taking any

measurement. If the electrode

has been left dry, soak the tip

(bottom 2.5 cm) in M10000B

rinse solution for a few minutes

to reactivate it.

• Make sure that the meter has

been calibrated before taking

any measurements (see Calibra-

tion Procedure).

• Immerse the tip (2.5 cm) of the pH-electrode into the sample.

• Turn the instrument on by pressing the ON/OFF key.

• Allow the reading to stabilize and the meter will start continuous

monitoring.

• A blinking alarm will indicate when the measured pH value is

higher than selected setpoint.

NOTE: The output power contact (SMS122 only) has no protection

fuse inside the meter. It is recommended to protected it outside,

against failure.

SETPOINT:

• The setpoint can be selected by adjust-

ing the central front knob to the desired

value.

• The selectable range is from 3.5 to 7.5

pH for SMS110; from 5.5 to 9.5 pH for

SMS120 and SMS122.

CALIBRATION PROCEDURE:

• Remove the protective cap from the electrode.

• Immerse the electrode tip into a new sachet of pH 7

calibration solution and allow the reading to stabi-

lize.

• Adjust the OFFSET calibration trimmer (on the front)

to display "7.0 pH".

• Open a new sachet of pH 4 calibration solution and

use a small quantity to rinse the electrode.

• Immerse the electrode tip into the pH 4 sachet and

allow the reading to stabilize.

• Adjust the SLOPE calibration trimmer (on the rear)

to display "4.0 pH".

• The calibration is now complete and the meter is

ready to take measurements.

• It is suggested to recalibrate the meter at least

once a month, after a prolonged stocking time

and after pH-electrode replacement.

INSTALLATION PROCEDURE:

(for SMS122 only)

Dieses Handbuch passt für folgende Modelle

Andere Milwaukee Messgerät Handbücher

Milwaukee

Milwaukee MW12 Bedienungsanleitung

Milwaukee

Milwaukee LDM 80 Bedienungsanleitung

Milwaukee

Milwaukee SM100 Bedienungsanleitung

Milwaukee

Milwaukee L4 CLL Bedienungsanleitung

Milwaukee

Milwaukee MW105 MAX Bedienungsanleitung

Milwaukee

Milwaukee 2205-40 Bedienungsanleitung

Milwaukee

Milwaukee 2280-20 Bedienungsanleitung

Milwaukee

Milwaukee 2231-20 Bedienungsanleitung

Milwaukee

Milwaukee M12 SPL Bedienungsanleitung

Milwaukee

Milwaukee 2212-20 Bedienungsanleitung

Milwaukee

Milwaukee MW101 Bedienungsanleitung

Milwaukee

Milwaukee REDLITHIUM L4 3PL Bedienungsanleitung

Milwaukee

Milwaukee REDLITHIUM Bedienungsanleitung

Milwaukee

Milwaukee MC510 Bedienungsanleitung

Milwaukee

Milwaukee LDM 45 Bedienungsanleitung

Milwaukee

Milwaukee MI 404 Bedienungsanleitung

Milwaukee

Milwaukee 2205-40 Bedienungsanleitung

Milwaukee

Milwaukee MA886 Bedienungsanleitung

Milwaukee

Milwaukee MI406 Bedienungsanleitung

Milwaukee

Milwaukee 2236-20 Bedienungsanleitung

Milwaukee

Milwaukee 2270-20 Bedienungsanleitung

Milwaukee

Milwaukee MW14 Bedienungsanleitung

Milwaukee

Milwaukee SMS510 Bedienungsanleitung

Milwaukee

Milwaukee MC510 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung