Minolta Dimage Scan Elite II Bedienungsanleitung

HARDWARE MANUAL

9222-2888-11 AV-A207

FOR PROPER AND SAFE USE

Read and understand all warnings and cautions before using this product.

WARNING

•Use only within the voltage range specified on the unit. Inappropriate current may cause

damage or injury through fire or electric shock.

•Use only the specified AC adapter (Delta Electronics ADP-20LB REV:B) within the voltage

range indicated on the adapter unit. An inappropriate adapter or current may cause damage or

injury through fire or electric shock.

•Do not disassemble this product. Electric shock may cause injury if a high-voltage circuit inside

the product is touched. Take the product to a Minolta Service Facility when repairs are required.

•Immediately unplug the unit and discontinue use if the product is dropped or subjected to an

impact in which the interior is exposed. The continued use of a damaged product may cause

injuries or fire.

•Store this product out of reach of children. Be careful when around children not to harm them

with the product or parts.

•Do not operate this product or handle the power cord with wet hands. Do not place a container

with liquid near the product. If liquid comes in contact with the product, immediately unplug the

unit. The continued use of a product exposed to a liquid may cause damage or injury through

fire or electric shock.

•Do not insert hands, inflammable objects, or metal objects such as paper clips or staples into

this product. It may cause damage or injury through fire or electric shock. Discontinue use if an

object enters the product.

•Do not use the product near inflammable gases or liquids such as gasoline, benzine, or paint

thinner. Do not use inflammable products such as alcohol, benzine, or paint thinner to clean the

product. The use of inflammable cleaners and solvents may cause an explosion or fire.

•When unplugging the unit, do not pull on the power cord. Hold the plug when removing the cord

from an outlet.

•Do not damage, twist, modify, heat, or place heavy objects on the power cord. A damaged cord

may cause damage or injury through fire or electric shock.

•If the product emits a strange odor, heat, or smoke, discontinue use. Immediately unplug the

product. The continued use of a damaged product or part may cause injuries or fire.

•Take the product to a Minolta Service Facility when repairs are required.

CAUTION

•This product should only be operated in the upright position. Inappropriate placement may

result in fire.

•Damage or injury through fire or electric shock may result if the product is used or stored in the

following conditions:

In humid or dusty environments

In direct sunlight or hot environments

In smoky or oily areas

In unventilated areas

On unstable or unlevel surfaces

•Insert the plug securely into the electrical outlet.

The sound pressure level is less than 70dB according to ISO 3744 or ISO 7779.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Tested by

the Minolta Corporation 101 Williams Drive Ramsey, New Jersey 07446 USA

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interfer-

ence received, including interference that may cause undesired oper-

ation. Do not remove the ferrite cores from the cables.

This mark certifies that this product meets the requirements of the EU (European

Union) concerning interference causing equipment regulations. CE stands for

Conformité Européenne.

As an ENERGY STAR Partner, Minolta has determined that this product meets

the ENERGY STAR guidelines for energy efficiency.

Microsoft, Windows, Windows 98, Windows Me, Windows 2000 Professional, and Windows NT

are registered trademarks of the Microsoft Corporation. Macintosh, Apple, and Power Macintosh

are registered trademarks of Apple Computer, Inc. Adobe and Photoshop are registered trade-

marks of Adobe Systems Incorporated. CorelPhotoPaint is a trademark of the Corel Corporation.

Paint Shop Pro is the copyright of Met’s Corporation. Digital ICE3, Digital ICE, Digital ROC, and

Digital GEM are trademarks of registered trademarks and technologies of Applied Science

Fiction,Inc in U. S. A. Other corporate and product names are the trademarks and registered

trademarks of their respective companies.

•Do not use if the cord is damaged.

•Do not connect the ground to a gas pipe, telephone ground, or water pipe. Improper grounding

can result in injury from electric shock.

•Do not cover the AC adapter. A fire may result.

•Do not obstruct access to the AC adapter; this can hinder the unplugging of the unit in

emergencies.

•Unplug the product when cleaning or when the unit is not in use for long periods.

•Periodically check that the power cord is not damaged and the plug is clean. Dust and dirt that

may collect between the prongs of the plugs may result in fire.

Every necessary precaution has been taken to ensure the accuracy of this instruction manual.

Minolta is not responsible for any loss or damage caused from the operation of this product. This

manual may not be copied in part or whole without prior written permission from Minolta.

BEFORE YOU BEGIN

Thank you for purchasing this Minolta product. Please take the time to read through this instruc-

tion manual so you can enjoy all the features of your new scanner.

This manual contains information regarding products introduced before September, 2002. To

obtain compatibility information for products released after this date, contact a Minolta service

facility listed on the back cover of this manual. This product is designed to work with accessories

manufactured and distributed by Minolta. Using accessories or equipment not endorsed by

Minolta may result in unsatisfactory performance or damage to the product and its accessories.

Check the packing list before using this product. If any items are missing, immediately contact

your dealer.

Film holder FH-U1 Scanner unit Slide mount holder SH-U1

AC adapter AC-U10 with power cord. The

shape of the plug varies with destination.

USB cable UC-1 IEEE 1394 cable FC-1

Quick Reference Guide, and

warranty card

DiMAGE Scan Utility CD-

ROM, DiMAGE Instruction

Manuals-CD-ROM

and Adobe Photoshop

Elements CD-ROM

TABLE OF CONTENTS

System requirements........................................................................................6

Names of parts ................................................................................................7

Scanner setup ..................................................................................................8

Before connecting the scanner to the computer ....................................8

Connecting the USB cable ....................................................................8

Connecting the IEEE 1394 (FireWire) cable ..........................................9

Connecting the AC adapter ....................................................................9

Turning on the scanner ..........................................................................9

Loading the film holders ................................................................................10

Handling film ........................................................................................10

Where is the emulsion?........................................................................10

Loading 35mm film strips ....................................................................10

Loading mounted slides........................................................................11

Loading a film holder into the scanner ................................................11

Using the APS Adapter AD-10 (sold separately) ..................................12

Film format and type settings ..............................................................13

Ejecting a film holder ............................................................................13

Scanner notes ................................................................................................14

Adobe Photoshop Elements ................................................................14

Easy Scan Utility ..................................................................................14

About the DiMAGE Scan Utility ............................................................14

Digital ICE3 system requirements ........................................................15

Scanner color profiles ..........................................................................16

Scanner resolution................................................................................16

Disconnecting the scanner ..................................................................16

Job file lists ....................................................................................................18

35mm....................................................................................................18

APS ....................................................................................................19

Troubleshooting ..............................................................................................20

Checking software installation - Windows ............................................21

Technical support..................................................................................22

Warranty and product registration ........................................................22

Technical specifications ..................................................................................23

This manual contains information specific to this model scanner. This includes hardware setup

and use as well as notes about software operation for this model scanner. See the supplied

DiMAGE Scan Utility software manual for information on the installation and operation of the

scanner software.

SYSTEM REQUIREMENTS

100MB or more of available hard-disk space is required. 200MB or more is required when

scanning with 16-bit color depth.

IEEE1394 or preinstalled USB (ver.1.1) interface

* To use preinstalled Mac OS 8.6 with a built-in FireWire port, a Firewire 2.2 to 2.3.3 extension

must be installed. This software can be downloaded free of charge from the apple web site at

http://www.apple.com.

Check the Minolta web site for the latest compatibility information:

North America: http://www.minoltausa.com,

Europe: http://www.minoltasupport.com

TWAIN driver is compatible with

Photoshop 5.0.2, 5.5 6.0, and 7.0,

Photoshop LE 5.0, Photoshop Elements,

Paint Shop Pro 7, CorelPhotoPaint9.

Recommended IEEE boards: Adaptec

FireConnect 4300,

PROCOMP SpeedDemon 400P

Preinstalled OHCI compatible

non-DV dedicated IEEE1394 ports guar-

antied by the computer manufacturer.

640 x 480 monitor capable of displaying High

Color (16 bit) is required. 1024 x 768 monitor

is recommended.

Aminimum of 64MB (128MB with Windows

XP) of RAM. For memory requirements for

Digital ICE3, see page 15.

USB: preinstalled Windows 98, 98 Second

Edition, 2000 Professional, Me, or XP.

IEEE 1394: preinstalled Windows 2000

Professional, Me, or XP

Pentium 166 Mhz or later processor.

Pentium III processor is recommended when

scanning with 16-bit color depth. For memory

requirements for Digital ICE3, see page 15.

Operation is not guarantied for custom or

home built computers.

Plug-in is compatible with

Photoshop 5.0.2, 5.5, 6.0 and 7.0,

Photoshop LE 5.0, Photoshop Elements.

Preinstalled FireWire port.

640 x 480 monitor capable of displaying at

least 32,000 colors is required. 1024 x 768

monitor is recommended.

Aminimum of 64MB of RAM in addition to

the requirements for the Mac OS and appli-

cations. 128MB of RAM when scanning with

16-bit color depth. For memory requirements

for Digital ICE3, see page 15.

USB: preinstalled Mac OS 8.6 to 9.2.2

and Mac OS 10.1.3 to 10.1.5

FireWire: preinstalled Mac OS 8.6* to 9.2.2

PowerPC G3 or later. PowerPC G4 or later is

recommended when scanning with 16-bit

color depth or using Digital ROC or GEM.

For memory requirements for Digital ICE3,

see page 15.

The computer and the operating system must be guarantied by the manufacturer to support IEEE

1394 (FireWire), or USB interface. To use the scanner, your computer system must meet the fol-

lowing requirements:

NAMES OF PARTS

35 mm film-holder mark

APS adapter mark

Front door

Power switch

Indicator lamp

Eject button

IEEE 1394 portUSB portDC terminal

The unused port should be covered with its protective cap. When the scanner is stored, the

cables should be removed and the caps replaced in the ports.

Remove the protective cap from the USB

port. Securely plug the A connector of the

USB cable into the scanner’s USB port and

the B connector into the computer’s USB

port.

The scanner should be connected directly to

the computer. Attaching the scanner to a

USB hub may prevent proper operation.

When the scanner is initially connected to a

computer with a Windows 98, 98SE, or 2000

Professional operating system, the found-

new-hardware wizard will appear briefly. No

action is required. With Windows 2000, the

“Digital Signature Not Found…” message

may appear. Click the yes button to com-

plete the scanner installation.

When the scanner is initially connected to a

computer with a Windows XP operating sys-

tem, the found-new-hardware wizard will

appear. Click the next button. The “not

passed Windows Logo testing” message

appears. Click the continue-anyway button

to complete the scanner installation.

SCANNER SETUP

Before connecting the scanner to a computer, the DiMAGE Scan Utility must first be installed.

Read the software instruction manual for the installation procedure.

The scanner should be placed on a level surface free from vibrations. It should be located away

from direct sunlight and in a clean, dry, well-ventilated area.

Before connecting the scanner to a computer

The computer and all peripheral devices must be

off before connecting the scanner.

Connecting the USB cable

With the front door closed, turn on the scanner

with the power switch (1). Start up the computer.

When launching the DiMAGE Scan Utility, the

front door must be closed during initialization; the

indicator lamp will blink when the scanner is ini-

tializing. Once the indicator lamp glows steadily,

the scanner can be used.

Connect the power cable to the AC

adapter unit (1). Connect the output

plug of the AC adapter to the scanner’s

DC terminal (2). Plug the power cable

into a standard household outlet (3).

Remove the protective cap from the IEEE 1394

port. Securely plug the cable into the scanner’s

and computer’s IEEE 1394 port. Either end of

the cable can be connected to the IEEE 1394

port on the scanner or computer.

The scanner should be connected directly to the

computer. Attaching the scanner to an IEEE hub

may prevent proper operation.

Connecting the IEEE 1394 (FireWire) cable

Connecting the AC adapter

Turning on the scanner

LOADING THE FILM HOLDERS

Handling film

Where is the emulsion?

To achieve the best possible reproduction from the scanner, the film and film holder should be

free from dust and dirt. Always work with processed film in a clean, dust-free environment. Handle

film by the edges or mount to prevent fingerprints and dirt marring the image area. Special lint

free gloves are available from photographic equipment retailers for film handling as well as anti-

static cloths, brushes, and blowers for removing dust. Film cleaner can be used to remove oil,

grease, or dirt from film; carefully follow the manufacturer's instructions and precautions for the

film cleaning solvent.

When film is scanned, the emulsion side of the film should be down. When viewing the film

image, if the image is orientated correctly rather than a mirror image, the emulsion side is facing

down. If the image is abstract or symmetrical so its orientation is difficult to determine, the emul-

sion is down if the frame numbers and edge markings can be read correctly. With mounted slides,

the emulsion is on the same side of the mount as the film manufacturer's or processor’s name is

printed.

Film strips of up to six frames can be

loaded into the FH-U1 film holder. To

remove the cover, lift the tab at the

end of the film holder (1).

Loading 35mm film strips

With the emulsion down, place the film

on the base of the holder. Align the

film with the frame apertures.

Replace the cover. Slide the two pro-

trusions on the left side of the cover

into the two slots in the base (2).

Carefully lower the cover taking care

not to move the film. Snap the cover

closed by pressing the two push

marks on each side of the tab (3).

Andere Handbücher für Dimage Scan Elite II

Inhaltsverzeichnis

Andere Minolta Scanner Handbücher

Minolta

Minolta DIMAGE SCAN MULTI PRO Bedienungsanleitung

Minolta

Minolta Dimage Scan Dual2 AF-2820U Bedienungsanleitung

Minolta

Minolta QuickScan 35 Bedienungsanleitung

Minolta

Minolta DiMAGE Scan Multi PRO AF-5000 Bedienungsanleitung

Minolta

Minolta Dimage Scan Elite F-2900 Bedienungsanleitung

Minolta

Minolta Dimage Scan Multi Montageanleitung

Minolta

Minolta DIMAGE SCAN DUAL II AF-2820U Bedienungsanleitung

Minolta

Minolta Scanner Mode Bedienungsanleitung

Minolta

Minolta Dimage Scan Elite II Bedienungsanleitung

Minolta

Minolta DiMAGE Scan Multi PROAF-5000 Bedienungsanleitung

Minolta

Minolta DIMAGE SCAN ELITE 5400 Bedienungsanleitung

Minolta

Minolta PS7000 Bedienungsanleitung

Minolta

Minolta DIMAGE SCAN DUAL III Bedienungsanleitung

Minolta

Minolta DiMAGE Scan Dual III AF-2840 Bedienungsanleitung

Minolta

Minolta Dimage Scan Multi Bedienungsanleitung

Minolta

Minolta MS 6000 Bedienungsanleitung

Minolta

Minolta SC-100 Bedienungsanleitung

Minolta

Minolta DIMAGE SCAN SPEED Bedienungsanleitung

Minolta

Minolta Dimage Scan Multi Bedienungsanleitung

Minolta

Minolta Dimage Scan Multi2 Bedienungsanleitung

Minolta

Minolta PS7000 Bedienungsanleitung

Minolta

Minolta Dimage Scan Scan Elite I Bedienungsanleitung

Minolta

Minolta Dimage Scan Elite II Bedienungsanleitung

Minolta

Minolta Dimage Scan Elite F-2900 Bedienungsanleitung

Beliebte Scanner Handbücher anderer Marken

Z/I Imaging

Z/I Imaging PhotoScan 2001 Bedienungsanleitung

Renkforce

Renkforce DS100-5M Bedienungsanleitung

Image Access

Image Access WideTEK A2 Bedienungsanleitung

Canon

Canon imageFORMULA CR-120N Bedienungsanleitung

Fujitsu

Fujitsu FI-4860C2 Bedienungsanleitung

GeoSlam

GeoSlam ZEB Horizon Montageanleitung

Kodak

Kodak i5800 Scanner Bedienungsanleitung

Kodak

Kodak i7300 Bedienungsanleitung

Revopoint

Revopoint POP Bedienungsanleitung

Fujitsu

Fujitsu fi-4860C Bedienungsanleitung

Eddyfi Technologies

Eddyfi Technologies Floormap X Bedienungsanleitung

Faselase

Faselase F6 Bedienungsanleitung

Fujitsu

Fujitsu CardMinder Bedienungsanleitung

Uniden

Uniden BC340CRS Bedienungsanleitung

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Bedienungsanleitung

Mustek

Mustek PageExpress 4800 Pro Bedienungsanleitung

Optex

Optex 750830 Bedienungsanleitung

Innova

Innova 5210 Bedienungsanleitung