Mitsubishi Electric MELSERVO-MR-J4 GF Series Bedienungsanleitung

General-Purpose AC Servo

CC-Link IE Field Network Interface

Servo Amplifier Instruction Manual

(CC-Link IE Field Network Basic)

-MR-J4-_GF_

-MR-J4-_GF_-RJ

SAFETY PRECAUTIONS

(Please read the instructions carefully before using the equipment.)

To use the equipment correctly, do not attempt to install, operate, maintain, or inspect the equipment until you have read

through this Instruction Manual, Installation guide, and appended documents carefully. Do not use the equipment until you

have a full knowledge of the equipment, safety information and instructions.

In this Instruction Manual, the safety instruction levels are classified into "WARNING" and "CAUTION".

Note that the CAUTION level may lead to a serious consequence according to conditions.

Please follow the instructions of both levels because they are important to personnel safety.

What must not be done and what must be done are indicated by the following diagrammatic symbols.

In this Instruction Manual, instructions at a lower level than the above, instructions for other functions, and so on are classified

into "POINT".

After reading this Instruction Manual, keep it accessible to the operator.

WARNING Indicates that incorrect handling may cause hazardous conditions, resulting in

death or severe injury.

CAUTION Indicates that incorrect handling may cause hazardous conditions, resulting in

minor or moderate injury or property damage.

Indicates what must not be done. For example, "No Fire" is indicated by .

Indicates what must be done. For example, grounding is indicated by .

[To prevent electric shock, note the following]

[To prevent fire, note the following]

WARNING

●Before wiring and inspections, turn off the power and wait for 15 minutes or more until the charge

lamp turns off. Then, confirm that the voltage between P+ and N- is safe with a voltage tester and

others. Otherwise, an electric shock may occur. In addition, when confirming whether the charge lamp

is off or not, always confirm it from the front of the servo amplifier.

●Ground the servo amplifier and servo motor securely.

●Any person who is involved in wiring and inspection should be fully competent to do the work.

●Do not attempt to wire the servo amplifier and servo motor until they have been installed. Otherwise, it

may cause an electric shock.

●Do not operate switches with wet hands. Otherwise, it may cause an electric shock.

●The cables should not be damaged, stressed, loaded, or pinched. Otherwise, it may cause an electric

shock.

●During power-on or operation, do not open the front cover of the servo amplifier. Otherwise, it may

cause an electric shock.

●Do not operate the servo amplifier with the front cover removed. High-voltage terminals and charging

area are exposed and you may get an electric shock.

●Except for wiring and periodic inspection, do not remove the front cover of the servo amplifier even if

the power is off. The servo amplifier is charged and you may get an electric shock.

●To prevent an electric shock, always connect the protective earth (PE) terminal (marked ) of the

servo amplifier to the protective earth (PE) of the cabinet.

●To avoid an electric shock, insulate the connections of the power supply terminals.

CAUTION

●Install the servo amplifier, servo motor, and regenerative resistor on incombustible material. Installing

them directly or close to combustibles will lead to smoke or a fire.

●Always connect a magnetic contactor between the power supply and the main circuit power supply

(L1/L2/L3) of the servo amplifier, in order to configure a circuit that shuts down the power supply on

the side of the servo amplifier's power supply. If a magnetic contactor is not connected, continuous

flow of a large current may cause smoke or a fire when the servo amplifier malfunctions.

●Always connect a molded-case circuit breaker, or a fuse to each servo amplifier between the power

supply and the main circuit power supply (L1/L2/L3) of the servo amplifier, in order to configure a

circuit that shuts down the power supply on the side of the servo amplifier's power supply. If a

moldedcase circuit breaker or fuse is not connected, continuous flow of a large current may cause

smoke or a fire when the servo amplifier malfunctions.

●When using the regenerative resistor, switch power off with the alarm signal. Otherwise, a

regenerative transistor malfunction or the like may overheat the regenerative resistor, causing smoke

or a fire.

●Provide adequate protection to prevent screws and other conductive matter, oil and other combustible

matter from entering the servo amplifier and servo motor.

[To prevent injury, note the following]

[Additional instructions]

CAUTION

●Only the power/signal specified in the Instruction Manual should be applied to each terminal.

Otherwise, it may cause an electric shock, fire, injury, etc.

●Connect cables to the correct terminals. Otherwise, a burst, damage, etc., may occur.

●Ensure that polarity (+/-) is correct. Otherwise, a burst, damage, etc., may occur.

●The servo amplifier heat sink, regenerative resistor, servo motor, etc., may be hot while the power is

on and for some time after power-off. Take safety measures such as providing covers to avoid

accidentally touching them by hands and parts such as cables.

The following instructions should also be fully noted. Incorrect handling may cause a malfunction, injury, electric shock, fire,

etc.

[Transportation and installation]

CAUTION

●Transport the products correctly according to their mass.

●Stacking in excess of the specified number of product packages is not allowed.

●Do not hold the front cover, cables, or connectors when carrying the servo amplifier. Otherwise, it may

drop.

●Install the servo amplifier and the servo motor in a load-bearing place in accordance with the

Instruction Manual.

●Do not get on or put heavy load on the equipment. Otherwise, it may cause injury.

●The equipment must be installed in the specified direction.

●Maintain specified clearances between the servo amplifier and the inner surfaces of a control cabinet

or other equipment.

●Do not install or operate the servo amplifier and servo motor which have been damaged or have any

parts missing.

●Do not block the intake and exhaust areas of the servo amplifier. Otherwise, it may cause a

malfunction.

●Do not drop or apply heavy impact on the servo amplifiers and the servo motors. Otherwise, it may

cause injury, malfunction, etc.

●Do not strike the connector. Otherwise, it may cause a connection failure, malfunction, etc.

●When you keep or use the equipment, please fulfill the following environment.

●When the product has been stored for an extended period of time, contact your local sales office.

●When handling the servo motor, be careful with the sharp edges of the servo motor.

●The servo amplifier must be installed in a metal cabinet.

●When fumigants that contain halogen materials, such as fluorine, chlorine, bromine, and iodine, are

used for disinfecting and protecting wooden packaging from insects, they cause a malfunction when

entering our products. Please take necessary precautions to ensure that remaining materials from

fumigant do not enter our products, or treat packaging with methods other than fumigation, such as

heat treatment. Additionally, disinfect and protect wood from insects before packing the products.

●To prevent a fire or injury in case of an earthquake or other natural disasters, securely install, mount,

and wire the servo motor in accordance with the Instruction Manual.

Item Environment

Operation 0 ˚C to 55 ˚C (non-freezing)

Ambient

temperature Storage -20 ˚C to 65 ˚C (non-freezing)

Operation 5 %RH to 90 %RH (non-condensing)

Ambient

humidity Storage

Ambience Indoors (no direct sunlight); no corrosive gas, inflammable gas, oil mist or dust

Altitude 2000 m or less above sea level (Contact your local sales office for the altitude for options.)

5.9 m/s2, at 10 Hz to 55 Hz (X, Y, Z axes)Vibration resistance

[Wiring]

CAUTION

●Wire the equipment correctly and securely. Otherwise, the servo motor may operate unexpectedly.

●Make sure to connect the cables and connectors by using the fixing screws and the locking

mechanism. Otherwise, the cables and connectors may be disconnected during operation.

●Do not install a power capacitor, surge killer, or radio noise filter (optional FR-BIF(-H)) on the servo

amplifier output side.

●To avoid a malfunction, connect the wires to the correct phase terminals (U/V/W) of the servo amplifier

and servo motor.

●Connect the servo amplifier power output (U/V/W) to the servo motor power input (U/V/W) directly. Do

not connect a magnetic contactor and others between them. Otherwise, it may cause a malfunction.

●The connection diagrams in this Instruction Manual are shown for sink interfaces, unless stated

otherwise.

●The surge absorbing diode installed to the DC relay for control output should be fitted in the specified

direction. Otherwise, the converter unit and the drive unit will malfunction and will not output signals,

disabling the emergency stop and other protective circuits.

●When the wires are not tightened enough to the terminal block, the wires or terminal block may

generate heat because of the poor contact. Be sure to tighten the wires with specified torque.

●Connecting a servo motor of the wrong axis to U, V, W, or CN2 of the servo amplifier may cause a

malfunction.

●Configure a circuit to turn off EM2 or EM1 when the main circuit power supply is turned off to prevent

an unexpected restart of the servo amplifier.

●To prevent malfunction, avoid bundling power lines (input/output) and signal cables together or

running them in parallel to each other. Separate the power lines from the signal cables.

Servo motorServo amplifier Servo motorServo amplifier

DOCOM

DC 24 V

DOCOM

DC 24 V

Servo amplifier Servo amplifier

Control output

signal

Control output

signal

For source output interface

For sink output interface

[Test run and adjustment]

[Usage]

CAUTION

●When executing a test run, follow the notice and procedures in this instruction manual. Otherwise, it

may cause a malfunction, damage to the machine, or injury.

●Before operation, check and adjust the parameter settings. Improper settings may cause some

machines to operate unexpectedly.

●Never make a drastic adjustment or change to the parameter values as doing so will make the

operation unstable.

●Do not get close to moving parts during the servo-on status.

CAUTION

●Provide an external emergency stop circuit to stop the operation and shut the power off immediately.

●For equipment in which the moving part of the machine may collide against the load side, install a limit

switch or stopper to the end of the moving part. The machine may be damaged due to a collision.

●Do not disassemble, repair, or modify the product. Otherwise, it may cause an electric shock, fire,

injury, etc. Disassembled, repaired, and/or modified products are not covered under warranty.

●Before resetting an alarm, make sure that the run signal of the servo amplifier is off in order to prevent

a sudden restart. Otherwise, it may cause an accident.

●Use a noise filter, etc., to minimize the influence of electromagnetic interference. Electromagnetic

interference may affect the electronic equipment used near the servo amplifier.

●Do not burn or destroy the servo amplifier. Doing so may generate a toxic gas.

●Use the servo amplifier with the specified servo motor.

●Wire options and peripheral equipment, etc. correctly in the specified combination. Otherwise, it may

cause an electric shock, fire, injury, etc.

●The electromagnetic brake on the servo motor is designed to hold the motor shaft and should not be

used for ordinary braking.

●For such reasons as incorrect wiring, service life, and mechanical structure (e.g. where a ball screw

and the servo motor are coupled via a timing belt), the electromagnetic brake may not hold the motor

shaft. To ensure safety, install a stopper on the machine side.

●If the dynamic brake is activated at power-off, alarm occurrence, etc., do not rotate the servo motor by

an external force. Otherwise, it may cause a malfunction of the dynamic brake or a fire.

[Corrective actions]

[Maintenance, inspection and parts replacement]

[General instruction]

CAUTION

●Ensure safety by confirming the power off, etc. before performing corrective actions. Otherwise, it may

cause an accident.

●If it is assumed that a power failure, machine stoppage, or product malfunction may result in a

hazardous situation, use a servo motor with an electromagnetic brake or provide an external brake

system for holding purpose to prevent such hazard.

●Configure an electromagnetic brake circuit which is interlocked with an external emergency stop

switch.

●When an alarm occurs, eliminate its cause, ensure safety, and deactivate the alarm to restart

operation.

●If the molded-case circuit breaker or fuse is activated, be sure to remove the cause and secure safety

before switching the power on. If necessary, replace the servo amplifier and recheck the wiring.

Otherwise, it may cause smoke, fire, or an electric shock.

●Provide an adequate protection to prevent unexpected restart after an instantaneous power failure.

●After an earthquake or other natural disasters, ensure safety by checking the conditions of the

installation, mounting, wiring, and equipment before switching the power on to prevent an electric

shock, injury, or fire.

CAUTION

●Make sure that the emergency stop circuit operates properly such that an operation can be stopped

immediately and a power is shut off by the emergency stop switch.

●It is recommended that the servo amplifier be replaced every 10 years when it is used in general

environment.

●When using the servo amplifier that has not been energized for an extended period of time, contact

your local sales office.

●To illustrate details, the equipment in the diagrams of this Instruction Manual may have been drawn

without covers and safety guards. When the equipment is operated, the covers and safety guards

must be installed as specified. Operation must be performed in accordance with this Instruction

Manual.

DC 24 V

Contacts must be opened when ALM (Malfunction) or

MBR (Electromagnetic brake interlock) turns off.

Contacts must be opened with the emergency stop switch.

Servo motor

Electromagnetic

brake

DISPOSAL OF WASTE

Please dispose a servo amplifier, battery (primary battery) and other options according to your local laws and regulations.

EEP-ROM LIFE

The number of write times to the EEP-ROM, which stores parameter settings, etc., is limited to 100,000. If the total number of

the following operations exceeds 100,000, the servo amplifier may malfunction when the EEP-ROM reaches the end of its

useful life.

• Write to the EEP-ROM due to parameter setting changes

• Write to the EEP-ROM due to device changes

STO FUNCTION OF THE SERVO AMPLIFIER

When using the STO function of the servo amplifier, refer to chapter 13 of "MR-J4-_GF_(-RJ) Servo Amplifier Instruction

Manual (Motion Mode)".

For the MR-J3-D05 safety logic unit, refer to app. 5 of "MR-J4-_GF_(-RJ) Servo Amplifier Instruction Manual (Motion Mode)".

COMPLIANCE WITH GLOBAL STANDARDS

For the compliance with global standards, refer to app. 4 of "MR-J4-_GF_(-RJ) Servo Amplifier Instruction Manual (Motion

Mode)".

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Electric Verstärker Handbücher

Mitsubishi Electric

Mitsubishi Electric MR-J3-B Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-JE-_A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J4 series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-J4-_GF Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO MR-J2-A Montageanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J5 MR-J5-G Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-J4W2-22B Kurzanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J4 series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J2 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-JE-_A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-J3-B-RJ006 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-JE-C Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J5 MR-J5-G Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J5 MR-J5-G Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J5 MR-J5-G-N1 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric SERVO SYSTEM MELSERVO-J5 MR-J5-A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Melservo-J2-JR SERIES Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-J2M-P8B Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Melservo-J3 Series MR-J3-B Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Melservo-J3 Series MR-J3-B Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-J2S-*B Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J2-Super Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO MR-J3-xT Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO MR-J2S- A Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung