Mitsubishi Electric MR-J2M-P8B Bedienungsanleitung

www.dadehpardazan.ir 88594014-15

General-Purpose AC Servo

MODEL

MR-J2M-P8B

MR-J2M- DU

MR-J2M-BU

SERVO AMPLIFIER

INSTRUCTION MANUAL

SSCNET Compatible

J2M Series

ﮐﺮﺷﮏﯾﺮﺘﮑﻟا ﯽﺸﯿﺑﻮﺴﺘﯿﻣ:ﯽﺘﻌﻨﺻ نﻮﯿﺳﺎﻣﻮﺗا تﻻﻮﺼﺤﻣ عاﻮﻧا هﺪﻨﻨﮐ ﺪﯿﻟﻮﺗ -ﯾارد وﺮﺳ ورﺗﻣ وﺮﺳ

-ﺮﺗرﻨﯾا -PLC -ﯽﺘﻌﻨﺻ يﺎﻫﺮﮕﺸﯾﺎﻤﻧ

-ادﺎﮑﺳا ﻢﺘﺴﯿﺳ

-ﯽﺘﻌﻨﺻ يﺎﻫ تﺎﺑر

-لﺎﺘﻣ ﯽﺑ ورﺘﮐﺎﺘﻨﮐ

-ﯽﺘﻇﺎﻔﺣ يﺎﻫ ﻪﻟر

-يﺮﯿﮔ هزاﺪﻧا يﺎﻫ ﻢﺘﺴﯿﺳ

ﺘﺸﭘ تﺎﻣﺪﺧ ﻪﺋارا ﺎﯿﻠﯾا ﺪﻨﻤﺷﻫ نازادﺮﭘ هداد ﺖﮐﺮﺷهﺪﻨﻨﮐ ﻦﯿﻣﺎﺗ ويا ﻪﻓﺮﺣ ﯽﻧﺎﺒﯿ

تاﺰﯿﻬﺠﺗMitsubishiElectric

ﯽﺷزﻣآ يﺎﻫ هرود يراﺰﮔﺮﺑPLC–HMI–Servo–Sensor–Inverter–Industrial Network

ﯽﺘﻌﻨﺻ نﯿﺳﺎﻣﺗا يﺎﻫژوﺮﭘ مﺎﺠﻧا

ﯽﺘﻌﻨﺻ نﯿﺳﺎﻣﺗا تاودا ﻪﯿﻠﮐ ﯽﺼﺼﺨﺗ تاﺮﯿﻤﻌﺗ

: سﺎﻤﺗ يﺎﻫ ﻦﻔﻠﺗ15-88594014: ﺲﮑﻓ88594013

بو: ﺖﯾﺎﺳwww.dphi.ir – www.indus.ir

www.dadehpardazan.ir 88594014-15

A - 1

Safety Instructions

(Always read these instructions before using the equipment.)

Do not attempt to install, operate, maintain or inspect the units until you have read through this Instruction

Manual, Installation Guide, Servo Motor Instruction Manual and appended documents carefully and can use

the equipment properly. Do not use the units until you have a full knowledge of the equipment, safety

information and instructions.

In this Instruction Manual, the safety instruction levels are classified into "WARNING" and "CAUTION".

WARNING Indicates that incorrect handling may cause hazardous conditions,

resulting in death or severe injury.

CAUTION Indicates that incorrect handling may cause hazardous conditions,

resulting in medium or slight injury to personnel or may cause physical

damage.

Note that the CAUTION level may lead to a serious consequence according to conditions. Please follow the

instructions of both levels because they are important to personnel safety.

What must not be done and what must be done are indicated by the following diagrammatic symbols:

: Indicates what must not be done. For example, "No Fire" is indicated by .

: Indicates what must be done. For example, grounding is indicated by .

In this Instruction Manual, instructions at a lower level than the above, instructions for other functions, and so

on are classified into "POINT".

After reading this Instruction Manual, always keep it accessible to the operator.

www.dadehpardazan.ir 88594014-15

A - 2

1. To prevent electric shock, note the following:

WARNING

Before wiring or inspection, switch power off and wait for more than 15 minutes. Then, confirm the voltage

is safe with voltage tester. Otherwise, you may get an electric shock.

Connect the base unit and servo motor to ground.

Any person who is involved in wiring and inspection should be fully competent to do the work.

Do not attempt to wire for each unit and the servo motor until they are installed. Otherwise, you can obtain

the electric shock.

Operate the switches with dry hand to prevent an electric shock.

The cables should not be damaged, stressed, loaded, or pinched. Otherwise, you may get an electric

shock.

During power-on or operation, do not open the front cover of the servo amplifier. You may get an electric

shock.

Do not operate the servo amplifier with the front cover removed. High-voltage terminals and charging area

are exposed and you may get an electric shock.

Except for wiring or periodic inspection, do not remove the front cover even of the servo amplifier if the

power is off. The servo amplifier is charged and you may get an electric shock.

2. To prevent fire, note the following: CAUTION

Do not install the base unit, servo motor and regenerative brake resistor on or near combustibles.

Otherwise a fire may cause.

When each unit has become faulty, switch off the main base unit power side. Continuous flow of a large

current may cause a fire.

When a regenerative brake resistor is used, use an alarm signal to switch main power off. Otherwise, a

regenerative brake transistor fault or the like may overheat the regenerative brake resistor, causing a fire.

3. To prevent injury, note the follow CAUTION

Only the voltage specified in the Instruction Manual should be applied to each terminal. Otherwise, a

burst, damage, etc. may occur.

Connect the terminals correctly to prevent a burst, damage, etc.

Ensure that polarity ( , ) is correct. Otherwise, a burst, damage, etc. may occur.

Take safety measures, e.g. provide covers, to prevent accidental contact of hands and parts (cables, etc.)

with the servo amplifier heat sink, regenerative brake resistor, servo motor, etc.since they may be hot

while power is on or for some time after power-off. Their temperatures may be high and you may get

burnt or a parts may damaged.

During operation, never touch the rotating parts of the servo motor. Doing so can cause injury.

www.dadehpardazan.ir 88594014-15

A - 3

4. Additional instructions

The following instructions should also be fully noted. Incorrect handling may cause a fault, injury, electric

shock, etc.

(1) Transportation and installation CAUTION

Transport the products correctly according to their masses.

Stacking in excess of the specified number of products is not allowed.

Do not carry the servo motor by the cables, shaft or encoder.

Do not hold the front cover to transport each unit. Each unit may drop.

Install the each unit in a load-bearing place in accordance with the Instruction Manual.

Do not climb or stand on servo equipment. Do not put heavy objects on equipment.

The controller and servo motor must be installed in the specified direction.

Leave specified clearances between the base unit and control enclosure walls or other equipment.

Do not install or operate the unit and servo motor which has been damaged or has any parts missing.

Provide adequate protection to prevent screws and other conductive matter, oil and other combustible

matter from entering each unit and servo motor.

Do not drop or strike each unit or servo motor. Isolate from all impact loads.

When you keep or use it, please fulfill the following environmental conditions.

Conditions

Environment Each unit Servo motor

[] 0 to 55 (non-freezing) 0 to 40 (non-freezing)

During

operation [] 32 to 131 (non-freezing) 32 to 104 (non-freezing)

[ ] 20 to 65 (non-freezing) 15 to 70 (non-freezing)

Ambient

temperature In storage []4 to 149 (non-freezing) 5 to 158 (non-freezing)

During

operation 90%RH or less (non-condensing) 80%RH or less (non-condensing)

Ambient

humidity In storage 90%RH or less (non-condensing)

Ambience Indoors (no direct sunlight) Free from corrosive gas, flammable gas, oil mist, dust and dirt

Altitude Max. 1000m (3280 ft) above sea level

[m/s2] 5.9 or less HC-KFS Series

HC-MFS Series

HC-UFS13 to 43 XY : 49

(Note)

Vibration [ft/s2] 19.4 or less HC-KFS Series

HC-MFS Series

HC-UFS13 to 43 XY : 161

Note. Except the servo motor with reduction gear.

Securely attach the servo motor to the machine. If attach insecurely, the servo motor may come off during

operation.

The servo motor with reduction gear must be installed in the specified direction to prevent oil leakage.

Take safety measures, e.g. provide covers, to prevent accidental access to the rotating parts of the servo

motor during operation.

Never hit the servo motor or shaft, especially when coupling the servo motor to the machine. The encoder

may become faulty.

Do not subject the servo motor shaft to more than the permissible load. Otherwise, the shaft may break.

When the equipment has been stored for an extended period of time, consult Mitsubishi.

www.dadehpardazan.ir 88594014-15

A - 4

(2) Wiring CAUTION

Wire the equipment correctly and securely. Otherwise, the servo motor may misoperate.

Do not install a power capacitor, surge absorber or radio noise filter (FR-BIF option) between the servo

motor and drive unit.

Connect the output terminals (U, V, W) correctly. Otherwise, the servo motor will operate improperly.

Connect the servo motor power terminal (U, V, W) to the servo motor power input terminal (U, V, W)

directly. Do not let a magnetic contactor, etc. intervene.

Drive unit

Servo Motor

Do not connect AC power directly to the servo motor. Otherwise, a fault may occur.

The surge absorbing diode installed on the DC output signal relay of the servo amplifier must be wired in

the specified direction. Otherwise, the forced stop and other protective circuits may not operate.

Interface unit

Control output

signal

VIN

RARA

Interface unit

Control output

signal

(3) Test run adjustment CAUTION

Before operation, check the parameter settings. Improper settings may cause some machines to perform

unexpected operation.

The parameter settings must not be changed excessively. Operation will be insatiable.

www.dadehpardazan.ir 88594014-15

A - 5

(4) Usage CAUTION

Provide a emergency stop circuit to ensure that operation can be stopped and power switched off

immediately.

Any person who is involved in disassembly and repair should be fully competent to do the work.

Before resetting an alarm, make sure that the run signal of the servo amplifier is off to prevent an accident.

A sudden restart is made if an alarm is reset with the run signal on.

Do not modify the equipment.

Use a noise filter, etc. to minimize the influence of electromagnetic interference, which may be caused by

electronic equipment used near MELSERVO-J2M.

Burning or breaking each unit may cause a toxic gas. Do not burn or break each unit.

Use the drive unit with the specified servo motor.

The electromagnetic brake on the servo motor is designed to hold the motor shaft and should not be used

for ordinary braking.

For such reasons as service life and mechanical structure (e.g. where a ballscrew and the servo motor

are coupled via a timing belt), the electromagnetic brake may not hold the motor shaft. To ensure safety,

install a stopper on the machine side.

(5) Corrective actions CAUTION

When it is assumed that a hazardous condition may take place at the occur due to a power failure or a

product fault, use a servo motor with electromagnetic brake or an external brake mechanism for the

purpose of prevention.

Configure the electromagnetic brake circuit so that it is activated not only by the interface unit signals but

also by a forced stop (EM1).

EM1RA

24VDC

Contacts must be open when

servo-off, when an alarm occurrence

and when an electromagnetic brake

interlock (MBR).

Electromagnetic brake

Servo motor

Circuit must be

opened during

forced stop (EM1).

When any alarm has occurred, eliminate its cause, ensure safety, and deactivate the alarm before

restarting operation.

When power is restored after an instantaneous power failure, keep away from the machine because the

machine may be restarted suddenly (design the machine so that it is secured against hazard if restarted).

www.dadehpardazan.ir 88594014-15

A - 6

(6) Maintenance, inspection and parts replacement

CAUTION

With age, the electrolytic capacitor of the drive unit will deteriorate. To prevent a secondary accident due

to a fault, it is recommended to replace the electrolytic capacitor every 10 years when used in general

environment.

Please consult our sales representative.

(7) General instruction

To illustrate details, the equipment in the diagrams of this Instruction Manual may have been drawn

without covers and safety guards. When the equipment is operated, the covers and safety guards must

be installed as specified. Operation must be performed in accordance with this Instruction Manual.

www.dadehpardazan.ir 88594014-15

A - 7

About processing of waste

When you discard servo amplifier, a battery (primary battery), and other option articles, please follow the law of

each country (area).

FOR MAXIMUM SAFETY

These products have been manufactured as a general-purpose part for general industries, and have not

been designed or manufactured to be incorporated in a device or system used in purposes related to

human life.

Before using the products for special purposes such as nuclear power, electric power, aerospace,

medicine, passenger movement vehicles or under water relays, contact Mitsubishi.

These products have been manufactured under strict quality control. However, when installing the product

where major accidents or losses could occur if the product fails, install appropriate backup or failsafe

functions in the system.

EEP-ROM life

The number of write times to the EEP-ROM, which stores parameter settings, etc., is limited to 100,000. If

the total number of the following operations exceeds 100,000, the servo amplifier and/or converter unit may

fail when the EEP-ROM reaches the end of its useful life.

Write to the EEP-ROM due to parameter setting changes

Precautions for Choosing the Products

Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi;

machine damage or lost profits caused by faults in the Mitsubishi products; damage, secondary damage,

accident compensation caused by special factors unpredictable by Mitsubishi; damages to products other

than Mitsubishi products; and to other duties.

www.dadehpardazan.ir 88594014-15

A - 8

COMPLIANCE WITH EC DIRECTIVES

1. WHAT ARE EC DIRECTIVES?

The EC directives were issued to standardize the regulations of the EU countries and ensure smooth

distribution of safety-guaranteed products. In the EU countries, the machinery directive (effective in

January, 1995), EMC directive (effective in January, 1996) and low voltage directive (effective in January,

1997) of the EC directives require that products to be sold should meet their fundamental safety

requirements and carry the CE marks (CE marking). CE marking applies to machines and equipment

into which servo (MELSERVO-J2M is contained) have been installed.

(1) EMC directive

The EMC directive applies not to the servo units alone but to servo-incorporated machines and

equipment. This requires the EMC filters to be used with the servo-incorporated machines and

equipment to comply with the EMC directive. For specific EMC directive conforming methods, refer to

the EMC Installation Guidelines (IB(NA)67310).

(2) Low voltage directive

The low voltage directive applies also to MELSERVO-J2M. Hence, they are designed to comply with

the low voltage directive.

MELSERVO-J2M is certified by TUV, third-party assessment organization, to comply with the low

voltage directive.

(3) Machine directive

Not being machines, MELSERVO-J2M need not comply with this directive.

2. PRECAUTIONS FOR COMPLIANCE

(1) Unit and servo motors used

Use each units and servo motors which comply with the standard model.

Drive unit :MR-J2M- DU

Interface unit :MR-J2M-P8B

Base unit :MR-J2M-BU

Servo motor :HC-KFS

HC-MFS

HC-UFS

(2) Configuration

Reinforced

insulating

transformer

NFB MC M

No-fuse

breaker Magnetic

contactor

Reinforced

insulating type

24VDC

power

supply

MELSERVO-

J2M

Servo

motor

Control box

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Electric Verstärker Handbücher

Mitsubishi Electric

Mitsubishi Electric MR-J4 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J4 series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J5 MR-J5-G Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-JE Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-MR-J4 GF Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-J3-T Gebrauchsanweisung

Mitsubishi Electric

Mitsubishi Electric MELSERVO MR-J2-A Montageanleitung

Mitsubishi Electric

Mitsubishi Electric MR-J4 TM Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J4 series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Melservo-J2-JR SERIES Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J4 series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-JE-_A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-JE MR-JE-70A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J4 series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J5 MR-J5-G Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Melservo-J5 MR-J5 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO MRJ2S-B Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-J2S-*B Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Melservo-J3 Series MR-J3-B Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J4 series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-J2S-*A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J5 MR-J5-G Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Melservo-J3 Series MR-J3-B Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-J2-03B5 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung