Molex 207129 Series Bedienungsanleitung

Hand Crimp Tool for 0.60mm (.027") CP 0.6 Series Crimp Terminals

Doc No: ATS 638119100 Release Date: 02 12 07 UNCONTROLLED COPY Page 1 of 5

Revision: F Revision Date: 11 22 10

CONDUCTOR

BRUSH

STRIP LENGTH

SEAM

CONDUCTOR

CRIMP HEIGHT

CUT-OFF

TAB

BELL MOUTH

BEND UP

TWISTING

ROLLING

BEND

DOWN

WIRE

HAND CRIMP

TOOL

Application Tooling

Sp cification Sh t Ord r No. 63811-9100

FEATURES

 A full cycle ratcheting hand tool ensures complete crimps

 A precision user friendly terminal locator wire stop holds terminals in the proper crimping position

 This tool is WHMA IPCA620 Class 3 only with specified wire types and RoHS compliant

SCOPE

Products: 0.60mm (.027") CP 0.6 Female Crimp Terminal CMC connector 0.22 0.35mm2.

T rminal S ri s No. T rminal Ord r No. Wir Siz Insulation Diam t r Strip L ngth





Availabl in R l form only AWG mm² mm In. mm In.

98913 64322

98913 1019

98913 1229

98913 1329

98913 1349

98913 3019

64322 1019

64322 1229

64322 1329

64322 1349

0.35 1.25 1.40 .049 .055 3.50 .138

0.22 1.15 1.25 .045 .049 3.50 .138

 Customer to cut off terminal from reel: 0.30mm (.012”) maximum Cut off Tab.

Note: Terminal will accommodate the thin wall small insulation with the IR or ID type Metric wires.

DEFINITION OF TERMS

TYPE 7

Hand Crimp Tool for 0.60mm (.027") CP 0.6 Series Crimp Terminals

Doc No: ATS 638119100 Release Date: 02 12 07 UNCONTROLLED COPY Page 2 of 5

Revision: F Revision Date: 11 22 10

CRIMP SPECIFICATION

After crimping, the conductor profiles should measure the following, see note.

T rminal S ri s No. Wir Siz Conductor Crimp Insulation Crimp Pull Forc

Minimum Profil

H ight (R f.) H ight (R f.)

AWG

mm2 mm In. mm In. N Lb. ----- 0.22-0.35

98913 0.35 0.70 0.80 .028 .031 1.40 1.55 .055 .061 60.0 13.50

Not in use

0.22 0.70 0.80 .028 .031 1.40 1.55 .055 .061 40.0 9.00

Not in use

64322 0.35 0.70 0.80 .028 .031 1.40 1.55 .055 .061 60.0 13.50

Not in use

0.22 0.70 0.80 .028 .031 1.40 1.55 .055 .061 40.0 9.00

Not in use

Not :

A crimp height chart is provided with this manual as Reference Only. Due to the wide range of wires, strands,

insulation diameters, and durometers, actual crimp height measurements may very slightly. An occasional,

destructive, pull force test should be preformed to check hand tool crimp. Pull Force value Must exceed the

Minimum pull force specifications listed.

OPERATION

CAUTION: Install only Molex terminals listed above with this tool. Do not crimp hardened objects as

damage can occur to the tool or die.

Open the tool by squeezing the handles together, at the end of

the closing stroke, the ratchet mechanism will release the

handles, and the hand tool will spring open.

Crimping T rminals

1. Select the desired terminal listed in the preceding charts.

2. Position the terminal from the back of the hand tool up and

into the proper locator opening with the crimp barrels

centered over the anvils. See Figure 1. Make sure when

choosing the correct nest and locator opening, it will

correspond with the pocket marked with the wire size profile

on the hand tool.

3. Partially close the jaws of the hand tool by squeezing the

handles until you hear the fist click of the ratchet. This will

move the wire stop into position.

4. From the front of the hand tool insert the pre stripped wire

over the terminal and against the wire stop. See Figure 2.

5. Compress the terminal by squeezing the tool handles until

the ratchet mechanism cycle has been completed. Release handles to open the jaws.

Note: The tamper proof ratchet action will not release the tool until it has been fully closed.

6. Remove the crimped terminal from the terminal locator.

7. Visually inspect the crimped terminal for proper crimp location.

Figur 1 LOCATOR

WIRE STOP

TERMINAL INSIDE

THE GROOVE

OF THE LOCATOR

BACK OF THE

HANDTOOL

Hand Crimp Tool for 0.60mm (.027") CP 0.6 Series Crimp Terminals

Doc No: ATS 638119100 Release Date: 02 12 07 UNCONTROLLED COPY Page 3 of 5

Revision: F Revision Date: 11 22 10

Maint nanc

It is recommended that each operator of the tool be made aware

of, and responsible for, the following maintenance steps:

1. Remove the plastic handles from the metal tool frame by

removing the screws and remove dust, moisture, and other

contaminants with a clean brush, or soft, lint free cloth.

2. Do not use any abrasive materials that could damage the

tool.

3. Make certain all pins; pivot points and bearing surfaces are

protected with a thin coat of high quality machine oil. Do not

oil excessively. The tool was engineered for durability but

like any fine piece of equipment it needs cleaning and

lubrication for a maximum service life of trouble free crimping. Light oil used at the pivot points every 5,000

crimps or 3 months, will significantly enhance the tool life.

4. Wipe excess oil from hand tool, particularly from crimping area.

5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies,

and store the tool in a clean, dry area.

Miscrimps or Jams

Should this tool ever become stuck or jammed in a partially closed

position, Do Not force the handles open or closed. The tool will

open easily by pressing the ratchet release lever up. See Figure 3.

How to Adjust Tool Pr load

It may be necessary over the life of the tool to adjust tool handle

preload force. Listed below are the steps required to adjust the

crimping force of the hand tool to obtain proper crimp conditions:

1. Remove the 2mm locking screw from the numbered adjusting

wheel using a screw driver. See Figure 4.

2. Using the same screw driver turn the adjustment wheel to the

next highest number.

Note: The uneven numbers are in clockwise (CW) direction and the even numbers are counter clockwise

(CCW).

3. Example: If the preload is set at number 5, then to increase the preload, turn the adjustment wheel until the

6th position is located over the 2mm locking screw tapped hole. If it is necessary to move to the 7th position,

then the adjustment wheel should be turned counter clockwise (CCW) until the 7th position is over the 2mm

locking screw tapped hole.

4. Replace the 2mm locking screw, aligning the nearest notch in the setting wheel to locking screw.

5. Check the crimp specifications and conduct a pull test after tool handle preload force is adjusted. Repeat

these steps until the desired result is obtained.

RATCHET

RELEASE LEVER

Figur 3

WIRE

Figur 2

WIRE IS UP AGAINST

THE WIRE STOP

FRONT OF THE

HAND TOOL

TERMINAL

Hand Crimp Tool for 0.60mm (.027") CP 0.6 Series Crimp Terminals

Doc No: ATS 638119100 Release Date: 02 12 07 UNCONTROLLED COPY Page 4 of 5

Revision: F Revision Date: 11 22 10

NUMBERED ADJUSTMENT

WHEEL

Figur 4

TURN CLOCKWISE (CW) OR

COUNTER CLOCKWISE (CCW)

TO ADJUST THE PRE-LOAD

TURN WITH A SMALL

SCREW DRIVER

REMOVE THE LOCKING 2MM SCREW

Warranty

This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital

components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30

days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will

not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. Any clamping,

fixturing, or use of handle extensions voids this warranty.

CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.

CAUTIONS:

1. Manually powered hand tools are intended for low volume, prototyping, or field repair. This tool is NOT

intended for production use. Repetitive use of this tool should be avoided.

2. Insulated rubber handles are not protection against electrical shock.

3. Wear eye protection at all times.

4. Use only the Molex terminals specified for crimping with this tool.

C rtification

Molex does not certify or re certify hand tools but rather supplies the following guidelines for customers to re

certify hand tools.

% This tool is qualified to pull force only. To re certify, crimp a terminal to a wire, which has been stripped

12.7mm (1/2”) long, so there is no crimping of the insulation. Pull the terminal and wire at a rate no faster than

25mm (1.00”) per minute. See the Molex web site for the Quality Crimp Handbook for more information on pull

testing.

% If the tool does not meet minimum pull force values, handle preload should be increased and the pull test

rerun, (See How to Adjust Preload).

% When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and

replaced.

Hand Crimp Tool for 0.60mm (.027") CP 0.6 Series Crimp Terminals

Doc No: ATS 638119100 Release Date: 02 12 07 UNCONTROLLED COPY Page 5 of 5

Revision: F Revision Date: 11 22 10

Figur 5

M3 X 6LG

BHCS

PARTS LIST

It m Numb r Ord r Numb r D scription Quantity

REF 63811-9100 Hand Crimp Tool Figur 5

1 63811 9175 Locator 1

2 11 11 0320 Spring (Ratchet) 1

3 63600 0479 Spring (Main) 1

4 69008 0972 Adjuster Wheel 1

http://www.molex.com

Andere Handbücher für 207129 Series

100

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere molex Crimpwerkzeuge Handbücher

molex

molex 207129 Series Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 63816-0900 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 63823-9100 Bedienungsanleitung

molex

molex 63825-7470 Benutzerhandbuch

molex

molex 207129 Series Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 63825-2800 Bedienungsanleitung

molex

molex 105300 Series Bedienungsanleitung

molex

molex 98897 Bedienungsanleitung

molex

molex RHT-4754 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 64001-1000 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 63811-5800 Bedienungsanleitung

molex

molex 63825-5500 Benutzerhandbuch

molex

molex 63819-3500 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex TPX50-50 Benutzerhandbuch

molex

molex 207129 Series Bedienungsanleitung

Beliebte Crimpwerkzeuge Handbücher anderer Marken

Panduit

Panduit CT-1000 Administratorhandbuch

JST

JST CS 10 Bedienungsanleitung

TE Connectivity

TE Connectivity 2063528-1 Bedienungsanleitung

Tyco Electronics

Tyco Electronics 69156-1 Bedienungsanleitung

CRH

CRH CRL CBLHCT1 Bedienungsanleitung

Emerson

Emerson Klauke ES 105CFM Bedienungsanleitung

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Bedienungsanleitung

Danfoss

Danfoss ET4350 Bedienungsanleitung

Milwaukee

Milwaukee M18 Bedienungsanleitung

HOGERT

HOGERT HT1P169 Bedienungsanleitung

Textron

Textron ESG105L Bedienungsanleitung

Tyco Electronics

Tyco Electronics 90035-3 Bedienungsanleitung

Emerson

Emerson Klauke ES 20RMCCFB Bedienungsanleitung

Continental Refrigerator

Continental Refrigerator PC150HD Bedienungsanleitung

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Bedienungsanleitung

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Bedienungsanleitung

Emerson

Emerson Klauke ES 105CFB Bedienungsanleitung

TE Connectivity

TE Connectivity 539 726-2 Bedienungsanleitung