Molex 207129 Series Bedienungsanleitung

Tool Kit for 250 MP-Lock Terminal

Doc No: ATS-6381 64HM Release Date: 0 -20-10 UNCONTROLLED COPY Page 1 of 8

Revision: B Revision Date: 0 -20-10

INSULATION

CRIMP

BRUSH

STRIP

LENGTH

CONDUCTOR

CRIMP HEIGHT

CUT-OFF

TAB

SEAM

BELL MOUTH

WIRE

Application Tooling

Sp cification Sh t

Tool Kit

Ord r No. 63819-6470

Hand Crimp Tool

Ord r No. 63819-6400

FEATURES

% A full cycle ratcheting hand tool ensures complete crimps

% Ergonomically designed soft handles

% Precisely designed crimping profiles with simple contact positioning

% Easy handling due to outstanding force ratio

 Tool kits are easily installed into the Hand Crimp Tool or the 63816-0300 Power Crimp Head which is installed

into the 63816-0200 (110 V) or the 63816-0250 (220 V) Battery Powered Tool.

 Many different Tool kits can be used with a single Battery Powered Tool.

 This tool is IPC/WHMA-A-620 Class 2 and RoHS compliant.

SCOPE

Products: .250 MP-Lock Terminals for 14 – 18 AWG Wire.

T rminal S ri s No.

T rminal Ord r No.

Wir Siz Insulation Diam t r Strip L ngth

R l Form Only

AWG

mm²

mm In. mm In.

35072 35072- 802

14 2.21

2.2 – 3.4

.086 - .133

5.0 - 5.6

.1 7 - .220

16 1.31

18 0.81

Customer to cut off terminal from reel: 0.50mm (.020”) maximum Cut-off Tab.

DEFINITION OF TERMS

The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the

scope.

TYPE 4C

Tool Kit for 250 MP-Lock Terminal

Doc No: ATS-6381 64HM Release Date: 0 -20-10 UNCONTROLLED COPY Page 2 of 8

Revision: B Revision Date: 0 -20-10

ANVILS

POWER

CRIMP

HEAD

Figur 1

PUNCHES

M4 X 10 LONG

BHCS

M4 X 18 LONG

BHCS

SWING

LOCATOR

OPEN

PRESS DOWN

ON THE BRASS

PIVOT SHAFT

LIFT UP ON

THE LOCATOR

Figur 2

CONDITIONS:

After crimping, the conductor profiles should measure the following (See notes below).

T rminal

S ri s No.

Wir Siz Conductor Crimp Insulation Crimp Pull Forc

Minimum Profil

H ight Punch Width (R f) H ight Punch Width (R f)

AWG

mm2

mm In. mm In. mm

In. mm In. N Lbs

35072

14 2.21

1.7 -1.8

.070-.074

2.80-2.82

.110-.111

4.00

.157

4.00-4.02

.157-.158

225.4

50.7

16 1.31

1.63-1.73

.064-.068

2.80-2.82

.110-.111

3.80

.150

4.00-4.02

.157-.158

1 6.0

44.1

18 0.81

1.47-1.57

.058-.062

2.80-2.82

.110-.111

3.60

.142

4.00-4.02

.157-.158

117.6

26.4

Tool Qualification Notes:

1. Pull Force should be measured with no influence from the insulation crimp.

2. The above specifications are guidelines to an optimum crimp.

Not :

A crimp height chart is provided with this manual as Reference Only. Due to the wide range of wires, strands,

insulation diameters, and durometers, actual crimp height measurements may very slightly. An occasional,

destructive, pull force test should be preformed to check hand tool crimp. Pull Force value must exceed the

minimum pull force specifications listed.

CAUTION: Install only Molex terminals listed above with this tool. Do not crimp hardened objects as damage

can occur to the tool or die.

INSTALLATION

To install the Tool Kit into the Power Crimp Head follow the steps below:

Anvils and Punch s Installation

1. Insert the Anvils into the bottom slots of the nest. Install the M4 x 10 long BHCS and tighten in place.

2. Insert the Punches into the top slots of the nest. Install the M4 x 18 long BHCS and tighten in place. See

Figure 1.

Tool Kit for 250 MP-Lock Terminal

Doc No: ATS-6381 64HM Release Date: 0 -20-10 UNCONTROLLED COPY Page 3 of 8

Revision: B Revision Date: 0 -20-10

SWING OPEN

TERMINAL

PUSH HERE TO

OPEN WIRE STOP LOCATOR TERMINAL

IN PLACE

Figur 4

LOCATOR LATCH

IN OPEN POSITION

Locator Installation and R moval

Follow the steps below to install or replace the locator. See Figure 2.

To install th locator

1. Position the locator with the hole over the brass pivot shaft and snap it into place.

To r mov th locator

1. Open the crimp hand tool.

2. Swing the existing locator open and away from the hand tool.

3. Firmly press down on the brass pivot shaft with your thumb, while pulling the locator up. Slip the locator off the

top of the brass pivot shaft.

OPERATION

Open the tool by squeezing the handles together, at the

end of the closing stroke, the ratchet mechanism will

release the handles, and the hand tool will spring open.

Crimping T rminals

1. Select the desired terminal listed in the preceding

charts.

2. Turn the Locator Lock Latch down to unlock. See

Figure 3.

3. Swing the terminal locator away from the crimp tool

shown in Figure 4. Some terminals with large insulation grips may interfere with the crimp tooling when

swinging the locator into position. The terminal must then be loaded into the locator in the closed/crimp

position. See Figure 5.

4. Press down on the wire stop on the locator as shown in Figure1. Insert the proper terminal into the proper nest

opening. Make sure when choosing the nest opening, it will correspond with the A, B or C profile on the hand

tool.

5. Return the locator to its

original position.

6. Turn the Locator Lock

Latch up to lock. Make

sure that the terminal is

visually centered over the

punch.

7. Insert the proper wire over

the terminal.

8. Gently touch the wire stop

with the end of the wire.

See Figure 6 and 7.

Figur 3

LATCH LOCKED

LATCH UNLOCKED

Tool Kit for 250 MP-Lock Terminal

Doc No: ATS-6381 64HM Release Date: 0 -20-10 UNCONTROLLED COPY Page 4 of 8

Revision: B Revision Date: 0 -20-10

Figur 6

WIRE IN TERMINAL

JAWS

PARTIALLY

CLOSED

WIRE AGAINST

WIRE STOP

HANDLE

OPEN

LOCATOR

CLOSED

Figur 5

TERMINAL

PUSH HERE TO

OPEN WIRE STOP

. Compress the terminal by squeezing the tool handles until the ratchet mechanism cycle has been completed.

Release handles to open the jaws.

10. Remove the crimped terminal from the terminal locator by pressing down on the wire stop and gently pulling on

the wire. The terminal locator can be in either position.

11. Visually inspect the crimped terminal for proper crimp location.

Not : The tamper proof ratchet action will not release the tool until it has been fully closed.

For th Batt ry Pow r Tool:

1. Cycle the Battery Power Tool to crimp the

terminal to the wire.

2. Remove the crimped terminal from the terminal

locator by pressing down on the wire stop and

gently pulling on the wire. The terminal locator

can be in either position.

3. Visually inspect the crimped terminal for proper

crimp location.

Maint nanc

It is recommended that each operator of the tool be

made aware of, and responsible for, the following

maintenance steps:

1. Remove dust, moisture and other contaminants

with a clean brush, or soft, lint-free cloth.

2. Do not use any abrasive materials that could damage the tool.

3. Make certain all pins; pivot points and bearing surfaces in the tool head are protected with a thin coat of high

quality machine oil. Do not oil excessively. This tool was engineered for durability, but like any fine piece of

equipment, it needs cleaning and lubrication for a maximum service life of trouble-free crimping. The use of

light oil, such as 30 weight automotive oil, every 5,000 crimps or monthly, will significantly enhance the tool life

and ensure a stable calibration. See Figure 8A or 8B for lubrication points.

4. Store the tool in a clean and dry area when not in use.

Figur 7

WIRE

INSULATION

PUNCH

CONDUCTOR ANVIL

LOCATOR

INSULATION

ANVIL

WIRES AGAINST

LOCATOR STOP

CONDUCTOR

PUNCH

TERMINAL

Tool Kit for 250 MP-Lock Terminal

Doc No: ATS-6381 64HM Release Date: 0 -20-10 UNCONTROLLED COPY Page 5 of 8

Revision: B Revision Date: 0 -20-10

Miscrimps or Jams for Crimp Hand Tools Only

(S Figur 11)

Should this tool ever become stuck or jammed

in a partially closed position, Do Not force the

handles open or closed. The tool will open

easily by rotating the small slotted screw

marked with an arrow. See Figure 11.

Warranty

This tool kit is for electrical terminal crimping

purposes only. This tool kit is made of the best

quality materials. All vital components are long

life tested. All tools are warranted to be free of

manufacturing defects for a period of 30 days.

Should such a defect occur, we will repair or

exchange the tool kit free of charge. This repair or exchange will not be applicable to altered, misused, or

damaged tools.

CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.

CAUTIONS

1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for

production use. Repetitive use of this tool should be avoided.

2. Insulated rubber handles are not protection against electrical shock.

3. Wear eye protection at all times.

4. Use only the Molex terminals specified for crimping with this tool.

CAUTION: Repetitive use of this tool should be avoided.

C rtification

Molex does not certify or re-certify commercial grade hand tools but rather supplies the following guidelines for

customers to re-certify hand tools.

% This tool is qualified to pull force only. To re-certify, crimp a terminal to a wire, which has been stripped

12.7mm (1/2”) long, so there is no crimping of the insulation. Pull the terminal and wire at a rate no faster than

25mm (1.00”) per minute. See the Molex web site for the Quality Crimp Handbook for more information on pull

testing.

% When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and

replaced.

% This tool is very difficult to disassemble and reassemble. Customer repair is not recommended.

LUBRICATION

POINTS

(BOTH SIDES)

LIGHT OIL

(EVERY MONTH

5,000 CRIMPS)

Figur 7A

Figur 7B

Tool Kit for 250 MP-Lock Terminal

Doc No: ATS-6381 64HM Release Date: 0 -20-10 UNCONTROLLED COPY Page 6 of 8

Revision: B Revision Date: 0 -20-10

The chart below shows all applications for this Tool Kit.

Tool Kit

Ord r No.

Tool

Ord r no.

Tool

D scription

Pow r H ad

Ord r No.

Adapt r

D scription

Figur

No.

6381 -6470

63810-1050

Hand Crimp Frame (Short) N/A N/A

63810-1000

Hand Crimp Frame (Long) N/A N/A

63816-0200

Battery Power Tool (110 V)

63816-0300 Power Crimp Head

63816-0250

Battery Power Tool (220 V)

63816-0300 Power Crimp Head

Applications for th Tool Kit

Hand Crimp Tool Batt ry Pow r d Tool

Figur 9 Figur 10

WARNING: NEVER operate service, install tool kits, or adjust the Power Crimp Head without proper

instruction and without first reading and understanding the instructions in the proper Manual or

Specification Sheet. See Chart above for the correct Manual or Specification Sheet.

WARNING: NEVER install tooling or service this tool while it is into any power source. Make sure the

power is turned off.

CAUTION: Keep fingers away from the crimping area when operating this tool. It may cause severe injury.

CAUTION: Wear safety glasses when operating or serving this tool.

OWER

CRIMP

HEAD

LOCKING PINS

BATTERY

POWERED

TOOL

TOOLING KIT

HAND CRIMP

FRAME LONG

AND SHORT

TOOLING KIT

Tool Kit for 250 MP-Lock Terminal

Doc No: ATS-6381 64HM Release Date: 0 -20-10 UNCONTROLLED COPY Page 7 of 8

Revision: B Revision Date: 0 -20-10

RATCHET

RELEASE SCREW

Figur 11

M4 X 8mm

LONG BHCS

M4 X 18mm

LONG BHCS

M4 X 10mm

LONG BHCS

WITH TOOL KIT

LOCATOR ONLY

HAND TOOL PARTS LIST

It m Numb r Ord r Numb r D scription Quantity

1 63810-1000 Hand Crimp Frame (Long) 1

2 6381 -6470 Tool Kit with Locator 1

3 63811-4773 Locator Base 1

4 6381 -6475 Locator (only) REF

Tool Kit for 250 MP-Lock Terminal

Doc No: ATS-6381 64HM Release Date: 0 -20-10 UNCONTROLLED COPY Page 8 of 8

Revision: B Revision Date: 0 -20-10

Figur 12

M4 by 8 Long

BHCS

M4 by 18 Long

BHCS

M4 by 10 Long

BHCS

POWER HEAD PARTS LIST

It m Ord r No Engin ring No. D scription Quantity

63816-0300 63816-0300 Power Crimp Head 1

6381 -6470 6381 -6470 Tool Kit 1

http://www.molex.com

Andere Handbücher für 207129 Series

100

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere molex Crimpwerkzeuge Handbücher

molex

molex 207129 Series Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 50098 Series Bedienungsanleitung

molex

molex 35745 Series Bedienungsanleitung

molex

molex 64001-7300 Bedienungsanleitung

molex

molex 63825-9570 Bedienungsanleitung

molex

molex 63811-7070 Bedienungsanleitung

molex

molex 63827-0470 Bedienungsanleitung

molex

molex 63819-4400 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 63825-8100 Bedienungsanleitung

molex

molex 63811-8300 Bedienungsanleitung

molex

molex 78172 Series Bedienungsanleitung

molex

molex 63819-3700 Bedienungsanleitung

molex

molex 63825-6070 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 63823-8000 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 63825-5770 Bedienungsanleitung

molex

molex 63811-5300 Bedienungsanleitung

molex

molex 64001-7400 Bedienungsanleitung

molex

molex 207129 Series Benutzerhandbuch

molex

molex 207129 Series Bedienungsanleitung

molex

molex 63811-6400 Bedienungsanleitung

Beliebte Crimpwerkzeuge Handbücher anderer Marken

Panduit

Panduit CT-1000 Administratorhandbuch

JST

JST CS 10 Bedienungsanleitung

Danfoss

Danfoss ET4200 Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

TE Connectivity

TE Connectivity 2063528-1 Bedienungsanleitung

Tyco Electronics

Tyco Electronics 69156-1 Bedienungsanleitung

CRH

CRH CRL CBLHCT1 Bedienungsanleitung

Emerson

Emerson Klauke ES 105CFM Bedienungsanleitung

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Bedienungsanleitung

Danfoss

Danfoss ET4350 Bedienungsanleitung

Milwaukee

Milwaukee M18 Bedienungsanleitung

HOGERT

HOGERT HT1P169 Bedienungsanleitung

Textron

Textron ESG105L Bedienungsanleitung

Tyco Electronics

Tyco Electronics 90035-3 Bedienungsanleitung

Emerson

Emerson Klauke ES 20RMCCFB Bedienungsanleitung

Continental Refrigerator

Continental Refrigerator PC150HD Bedienungsanleitung

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Bedienungsanleitung

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Bedienungsanleitung