Monte Carlo Fan Company 5DCR60XX Series Gebrauchsanweisung

Owner’s Guide and Installation Manual

Attach sales receipt to this card and retain as your proo o purchase

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

To register your ixture, please visit our website www.montecarlo ans.com

5DCR60XX Series Fan

Total an weight

UL Model No. : AC-560DC

11 kgs

24.2 lbs

Warning: Only blades that come with the fan are ac-

cepatable for installation.

Warning: This fan uses dimmable remote controller.

Do not install light kit with SBCFL (Self-Ballasted Com-

pact Fluorescent Lamp) on this fan.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA

70-1999), including fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be

turned upward and pushed carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

ake sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet

from the floor to the trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, ount To Outlet Box arked “Acceptable for Fan Support of

31.8 kg (70 lbs) or less” And Use ounting Screws Provided With The Outlet Box.

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do

not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.

WARNING: To reduce the risk of fire or electric shock, this fan should only be used with fan speed control part no. BJX1514AST manufac-

tured by Air Cool Industrial Co., Ltd.

WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed

control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating

equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the

American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

All set screws must be checked and tightened where necessary before installation.

Cutomer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlo ans.com

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,

Stepladder and Wire Strippers.

Before you begin installing the fan, Switch power off

at Service panel and lock service disconnecting means

to prevent power from being switched on accidentally.

When the service disconnecting means cannot be

locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

Warning-Risk of fire, electric shock, or person-

al injury. The fan in this box may be either

directly supported from a structural framing

member of a building and/or may be mounted

to an outlet box marked acceptable for fan sup-

port of of 31.8kg (70 lbs) or less. Most outlet

boxes commonly used for the support of lummi-

naires may not be acceptable for fan support

and may need to be replaced. Consult a quali-

fied electrician if in doubt.

2OUTLET BOX METHOD

Secure mounting plate directly to a joist from

the buliding structure via the two knock out

holes on the outlet box. Use only the appropri-

ate wood screws and washers included with

your fan. Caution: Wood screws must go

through into the building joist.

Outlet box

Mounting

Plate

Wood

Screws

BUILDING STRUCTURE METHOD

Remove the 6screws attaching the Mounting

neck the mounting plate. Retain the 6screws

for re-assembly.

Install the mounting Plate to approved fan

brace and box combination use only the hard-

ware provided with the fan brace and box.

6FAN BRACE AND BOX METHOD

Remove Safety bar from mounting bracket by

loosing screws, sliding bar to side, and lifting it

off the 2 screws.

Remove the keeper pin and cotter pin.

Lift mounting neck to mounting Plate and align

screws.

Secure mounting neck to the mounting plate

with 6screws to become a complete mount-

ing bracket.

Insert downrod into motor yoke.

Next, insert clevis pin through yoke

and downrod and secure with cotter

pin.

Carefully lift fan assembly onto

mounting bracket. Rotate fan so that

the notch on the ball engages the

ridge in the mounting bracket. This

will allow hands-free wiring.

Install canopy and yoke cover over

the downrod. Thread wire through

downrod with canopy and yoke cover

assembled.

Tighten both yoke set screws to fur-

ther secure downrod. Reinstall the

downrod ball previously removed.

Loosen the 2 set screws. You should

be able to put your downrod into the

yoke.

Remove the shipping stabilizers

and discard.

Hang assembled fan from the mounting bracket

installed to ceiling in previous step. Make sure

the fan is hanging straight. Rotate fan until the

tab on the Mounting bracket engages the slot

on the Downrod Ball. This must be done to

prevent the fan body from rotating when the

blades are in motion.

Re-install safety bar removed in step.

3 by placing safety bar on screws,

sliding into place, and tightening the

2 screws.

Install the two thumbscrews to

secure the yoke cover. Tighten

securely.

Loosen 2 screws and remove 1 screw

and save.

Attach blade assembly to motor

using the motor screws and washers

provided. Tighten screws securely.

Install 3 screws and washers per

blade and tighten securely. Repeat

for all 5 blades.

Place the gasket onto the blade

bracket as shown above.

Warning: Only blades that come

with the fan are accepatable for

installation.

Place blade onto blade bracket with

gasket.

Make sure that all exposed wiring is

secured inside wire nuts. Note: Wires

from house may vary in color and

may not include ground wire. After

wiring is conplete, gently push wires

into junction box with wire nuts

pointing upward. Refer to point 3 of

safety tips.

21 House Fan

Black

White

Green

Black

White

Green(downrod)

Green(Bracket)

Make wire connections to power source using

wire nuts provided. Make sure that no filiments

are outside of the wirenut. After making the

wire connections, the wires should be spread

apart with the grounded conductor and the

equipment-grounding conductor on one side of

the outlet box and ungrounded conductor on

the other side of the outlet box.

For Canadian installation and for USA fan and

light kit combinations over 35 lbs, in both flush

and downrod mode the safety cable must be

installed into the house structure beams using

the 3” lag screws,washers, and lock washers.

provided. Make sure that when the safety cable

is fully extended the leadwires are longer than

the cable and no stress is placed on the lead-

wires.

19 Safety cable installation

Safety Cable

Lag Screw

safety

cable

3” lag

screw

lock

washer

Loosen one and remove one preassem-

bled screw from mounting bracket. Save

screw. Lift canopy up, aligning its keyhole

slot with the preassembled screw on

mounting bracket and twist clockwise to

lock in place. Re-install the removed

screw and tighten all screws securely.

Install the switch housing using the

three screws previously removed.

Remove the 3 screws on the switch

housing plate and save.

Install the switch housing plate by

aligning the 2 screws with the 2 key

slot holes on the plate and twist to

lock into place. Install the 1 screw

removed and tighten the other 2

screws securely.

#/-/3>/:5/+:73710=7-<38768<8:

After the fan is powered (DC motor), the receiver will start sourcing the frequency in the first 30 sec-

onds; during the time, any instruction from the transmitter (pressing any button) will be recognized and

memorized as the D frequency of the using transmitter; frequencies from the other transmitters won’t

be identified as the instruction to operate your fan. When the power is off and on again, if the receiver

does not receive the frequency from the transmitter in 30 seconds, receiver will automatically use last

frequency set before the power off.

$/<<371=9<2/!;?3<-28558?,/58?;</9;

1.Cut off power supply (turn off the power switch) to the fan before setting up and matching between

the fan and the transmitter.

2.Then set/change the D P switch on the transmitter wanted to work with the fan.

3.Then re-connect the power supply (turn on) the fan again. 0<2/98?/:3;87+5:/+.@@8=6=;<

<=:7<2/98?/:80003:;<<=:7800<2/98?/:;?3<-2+7.<2/7<=:7<2/98?/:,+-408:5/+:7

0=7-<387;/<<371

4.Push any key on transmitter within 30 second (//99=;371<2/4/@08:+<5/+;<;/-87.;), the

fan will match and set up with the transmitter.

5.Repeat the above steps for the other set of fans and transmitters in the house.

$9/-3+578</

1. f there is a power failure, and you have more than one fan inside the house, do not push the trans-

mitter within 60 seconds, otherwise the transmitter signal will be picked up by all fans and the fans can-

not be controlled separately.

2.The fan can remember the running setting before power failure or cut off.

3. f the new fan runs after connected to power, it may be due to the fan remembering the previous

running setting in the factory during the QC process, push “stop” key on transmitter twice to stop.

9/:+<3877;<+55+<387

1. Remove the battery cover and the battery from the transmitter, you will see 4 dipswitches with on/off

printing, adjust the dipswitches with your own choice (different combinations).

2. Power your fan, use the transmitter to send the signal to the receiver by pressing any button on the

transmitter, the receiver will memorize the frequency from the transmitter as the D signal from now.

3. Refer to page 8 for remote control transmitter features.

%39;08:/7.=;/:;

1. Once the power is off from last using and you want to restart your fan, in case there are two fans or

more in your house with the same transmitter and receiver set, REMEMBER to wait for 60 seconds

before using the transmitter, otherwise it will cause a transmitter to control both fans in the same time.

2. Receiver has the memory function, fan will automatically return to the previous setting before power

off.

3. f your fan is operated automatically after installation, it is because your fan still memorize the previ-

ous setting at factory, just simply press the “stop” button on the transmitter twice to stop your fan.

4. When fan is turned on or operated forward/reverse function, it shutters & goes back & forth until it

turns. t is a normal performance of this fan and it will take for few seconds to run this operation.

5. f fan or light isn't working, reset the power ( turn power off and then turn it back ) and redo the

learn function.

FORWARD/REVERSE Depress reverse button and allow a few seconds

for remote to change rotation direction with fan running. The fan will come to

a complete stop and then run in the opposite direction. This process may take

20-30 seconds.

FAN OFF SETTING

(Turns fan off only)

FAN REVERSE (Press

once to change direction

of the fan)with fan run-

ning.

LIGHT ON/OFF SET-

TING AND DIMMER

(Press and hold to

dim light infinitively)

Fan speed control

FAN SPEED Depress “#1 bar is for highest speed.The #7 bar is for the lowest

speed.

LIGHT DIMMER To turn light on, press light dimmer once quickly. To turn

offpress once quickly while light is on. To dim light hold down button “light

dimmer”. The light will cycle from bright to dim to bright until button is

released. Light willmaintain last setting if turned off. ou can see the percentage

on the display screen.

NOTE: If you have more than 1

fan with a remote, you will have

to change the DIP switch settings

located above the battery of the

remote. There are no DIP switch-

es on the fan. Only change the

remote DIP switches. When the low battery

sign is shown on the

LCD display, replace a

new battery.

LIGHT DELAY

Pressing the light delay but-

ton activates the light delay

function. The light will auto-

matically shut off after 1

minute.

Memory for fan speed.

Press "M", fan will run

at the speed as last

setting if it was turned

off by remote con-

troller

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

3.Check learn function setting.

&% +4/;=:/6+3798?/:3;<=:7/.800

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

&% +4/;=:/6+3798?/:3;<=:7/.800,/08://7</:371;?3<-228=;371

4.Some fan motors are sensitive to signals from Solid State variable speed controls.   %

&$+$853.$<+</>+:3+,5/;9//.-87<:85

5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear

after this period.

1.Make sure that the ridge of the canopy engages the notch in the downrod ball.

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box

and junction box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the blades. Measure this distance from

blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade is posi-

tioned for measurement. Repeat for each blade. f all blade levels are not equal, you can

adjust blade levels by the following procedure. To adjust a blade tip down, insert a washer

(not supplied) between the blade and blade holder at the screw closest to the motor. To

adjust a blade tip up, insert washer (not supplied) between the blade and blade holder at the

two screws farthest from the motor. Reverse the position of the washer if blades mount from

top of blade.

6. f blade wobble is still noticeable, interchanging two adjacent (side by side) blades can

redistribute the weight and possibly result in smoother operation.

1.Check wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

5.Check learn function setting.

&% +4/;=:/6+3798?/:3;<=:7/.800,/08://7</:371;?3<-228=;371

(+:7371 75@,5+./;<2+<-86/?3<2<2/0+7+:/+--/9+<+,5/08:37;<+55+

<387

(+:7371%23;0+7=;/;.366+,5/:/68</-87<:855/:878<37;<+555312<43<

?3<2$$/50+55+;</.869+-<5=8:/;-/7<+6987<23;0+7

2. f fan sounds noisy:

1. f fan does not

start:

3. f fan wobbles:

4. f light does not

work:

Trouble Shooting

f you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation,

or wiring. n some cases, these installation errors may be mistaken for defects. f you experience any faults,

please check this Trouble Shooting Chart. f a problem cannot be remedied, or you are experiencing difficulty

in installation, please call our Customer Service Center at the number printed on your parts list insert sheet.

(+:7371/08:/;/:>3-3718:-5/+7371=73<$?3<-298?/:800+<$/:>3-/9+7/5+7.58-4;/:>3-/.3;

-877/-<3716/+7;<89:/>/7<98?/:0:86,/371;?3<-2/.87+--3./7<+55@(2/7<2/;/:>3-/.3;

-877/-<3716/+7;-+778<,/58-4/.;/-=:/5@0+;</7+9:8637/7<?+:7371./>3-/;=-2+;+<+1

<8<2/;/:>3-/9+7/5

Andere Handbücher für 5DCR60XX Series

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 5AB52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 4LNCR56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4BN44WHD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5AGR56 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3LR38 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DI52ES D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DIO52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5SI Series Fan Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5KC48 Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3FSR52 series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3STR60 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3RULSM52HABD Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Bravo 5BO52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4VOR60XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3DLR56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LDO44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AKR56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4TK52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HS42 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DOR52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MAVR88XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ROZR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5EM68 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3BTR54 Series Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung