Monte Carlo Fan Company Discus Trio Max 3DIR58 D Series Gebrauchsanweisung

Owner’s Guide and Installation Manual

Total fan weight with light

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

Attach sales receipt to this card and retain as yourproof of purchase

To register your fixture, please visit our website www.montecarlofans.com

3DIR58XXD Series Fan

UL Model NO. : 3DIR58XXD

9.4 kgs

20.7 lbs

Cautions and Warnings

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with applicable codes and standards (ANSI/NFPA 70) including

ﬁre-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side

of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be turned upward and pushed

carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to

prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the ﬂoor

to the trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of 15.9 kg (35 lbs)

or less” And Use Mounting Screws Provided With The Outlet Box.

CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Remove Knockouts

In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to the building structure (or the

ceiling joist).

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert

foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of ﬁre or electric shock, this fan must be installed with an isolating wall control/switch.

WARNING: To reduce the risk of ﬁre or electric shock, this fan should only be used with fan speed control part no. UC7067RA manufactured by Rhine

Electronic Co., Ltd.

WARNING: To reduce the risk of ﬁre or electric shock, do not use this fan with any other solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airﬂow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment

manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for

Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

CAUTION: The light source is designed for this speciﬁc application and can overheat if serviced by untrained personnel. If any servicing is required, the

product should be returned to an authorized service facility for examination or repair.

All set screws must be checked and tightened where necessary before installation.

Note: Suitable for use in damp locations.

1 2 3

4 5 6

OFF

Before you begin installing the fan, Switch

power off at Service panel and lock

service disconnecting means to prevent

power from being switched on

accidentally. When the service

disconnecting means cannot be locked,

securely fasten a warning device, such

as a tag, to the service panel.

Use AC 120V/60HZ power supply

only.

Before installing this fan make sure the

outlet box is properly installed to the

house structure. To reduce the risk of

ﬁre, electric shock, or personal injury,

mount to outlet box or supporting system

acceptable for fan support.

(Mounting must support at least 35 lbs.)

Use metal outlet box suitable for fan

support and use only the screws provided

with the outlet box (must support 35 lbs).

Before attaching fan to outlet box, ensure

the outlet box is securely fastened by at

least two points to a structural ceiling

member ( a loose box will cause the fan to

wobble). Remove the two outlet box

screws provided with the box, aligning

the holes of the mounting bracket with

the holes of the outlet box. Reinstall the 2

outlet box screws securely.

Partially loosen downrod set screws from

yoke at top of motor assembly.

Remove preassembled cross pin and

keeper pin from downrod.

Place downrod over canopy, canopy

bottom ring and yoke cover. Thread lead

wires and safety cable from motor

assembly through downrod.

Slip downrod into motor housing yoke,

aligning holes and install cross pin and

keeper pin.

Insert cross pin through yoke and downrod

until point appears on the other side, and

insert keeper pin on cross pin.

Pull the downrod up tight against the

cross pin, and then evenly tighten the

downrod set screws on motor housing

yoke.

Place yoke cover on top housing of fan.

Warning: Cross pin and keeper pin must be

installed securely, failure to install them will

result in serious injury.

Yoke cover

Mounting bracket

Downrod

Cross pin

Cross pin Keeper pin

Keeper pin

Canopy

Downrod

Canopy bottom ring

Downrod Mount Installation

7 8 9

10 11 12

Flush Mount Installation

Install ball end of downrod into mounting

bracket opening. Align (engage) slot on

ball with tab on mounting bracket.

Warning: Failure to align slot on ball with

tab may result in serious injury.

Important: If using the angle mount,

make sure open end of mounting bracket

is installed facing the higher point of the

ceiling and make sure the ceiling angle is

not steeper than 30º.

For Canadian installation and for USA fan

and light kit combinations over 35 lbs, in

both ﬂush and downrod modes the safety

cable must be installed into the house

structure beams using 3” lag screws,

washers and lock washers provided.

Make sure that when the safety cable is

fully extended the lead wires are longer

than the cable and no stress is placed on

the lead wires.

Note: If Installing The Secondary Support

Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box.

Make wiring connections using wire

connectors provided as indicated above.

White from fan to White from remote

marked N. Black from fan to Black from

remote marked L. Blue from fan to Blue

from remote marked FOR LIGHT. White

from house to White from remote marked

AC IN N. Black from house to Black from

remote marked AC IN L. Connect all

green grounded wires to Grounded wire

from House. Make sure that no ﬁlaments

are outside of the wire connectors.

Insert the remote receiver into mounting

bracket. Refer to page 7 for receiver

setting.

After making the wire connections, the wires

should be spread apart with the grounded

conductor and the equipment-grounding

conductor on one side of the outlet box and

ungrounded conductor on the other side of

the outlet box. The splices after being made

should be turned upward and pushed carefully

up into the outlet box.

Lift Canopy allowing the 2 studs to protrude

through the canopy.

Next lift the cover ring and install knurled nuts

as shown. Tighten the knurled nuts securely.

The canopy should adjust for any irregularity

in the ceiling or Outlet box.

Make sure the studs protruding from the

bottom of the Mounting bracket are installed

with threads all the way through the bracket.

Remove every other screws from yoke

located on top of fan assembly. Keep

screws.

Note: Flush mount is not available with

vaulted ceiling.

Tab

Slot

Go to step 20 to ﬁnish

installation

Stud

Wall switch

Black

(Live)

White

(Neutral)

Ground/Green

White

Black

Blue

Receiver

Power source

SAFETY CABLE INSTALLATION

Lag screw

Safety cable

Washer

Lock washer

Grounded

wires Ungrounded

wires

Receiver

13 14 15

16 17 18

Remove side covers from canopy

exposing 4 holes. 2 closed holes and 2

open “L” shape holes.

Reinstall the 3 set screws remove in step

12. Tighten screws securely.

To prepare the fan for wiring, hang fan

onto mounting bracket by sliding the

canopy over the mounting bracket hook

(Use one of non-slotted holes on the

rim of the canopy).

For Canadian installation and for USA fan

and light kit combinations over 35 lbs, in

both ﬂush and downrod modes the safety

cable must be installed into the house

structure beams using 3” lag screws,

washers and lock washers provided.

Make sure that when the safety cable is

fully extended the lead wires are longer

than the cable and no stress is placed on

the lead wires.

Note: If Installing The Secondary Support

Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box.

Make wiring connections using wire

connectors provided as indicated above.

White from fan to White from remote

marked N. Black from fan to Black from

remote marked L. Blue from fan to Blue

from remote marked FOR LIGHT. White

from house to White from remote marked

AC IN N. Black from house to Black from

remote marked AC IN L. Connect all

green grounded wires to Grounded wire

from House. Make sure that no ﬁlaments

are outside of the wire connectors.

Insert the remote receiver into mounting

bracket. Refer to page 7 for receiver

setting.

After making the wire connections, the wires

should be spread apart with the grounded

conductor and the equipment-grounding

conductor on one side of the outlet box and

ungrounded conductor on the other side of

the outlet box. The splices after being made

should be turned upward and pushed carefully

up into the outlet box.

Place rubber pad and canopy over lead

wire and safety cable and align the larger

holes in canopy and holes on rubber pad

with the set screws on yoke.

Side cover

Rubber pad

Lag screw

Safety cable

Washer

Lock washer

SAFETY CABLE INSTALLATION

Wall

switch

Power source

White

(Natural)

Black

(Live)

Black

Blue

White

Ground/Green

Receiver

Hook

Grounded

wires

Ungrounded

wires

Receiver

19 20

22 23

Install 2 of the screws to the side panel

of mounting bracket corresponding to the

open slotted holes on the canopy upper

rim, screws provided. Remove the all

thread studs from the lower part of the

mounting bracket.

Lift fan to mounting bracket, aligning the

“L” shape holes with the screws on the

mounting bracket. Turn the fan clockwise

to lock in position. Install the other 2

canopy mounting set screws from the

hardware pack and tighten all screws

securely.

Insert blade into the slot on ﬂywheel.

Install blade with screws and ﬁber

washers provided, aligning each of the

holes as shown and tighten all screws

securely. Repeat this process for

remaining blades.

Loosen 2 and remove 1 preassembled

screw from the plate on motor. Save

screw for later use.

Connect plug from fan to plug from light

pan. Be sure plugs connection clasped

together completely.

Aligning the keyhole slots on the light pan

with the preassembled screws on the

plate. Twist clockwise till lock. Reinstall

the screw which was just removed.

Tighten all screws securely.

Loosen 2 and remove 1 preassembled

screw from light pan. Save screw for later

use.

Connect white wire from light pan to white

wire from LED light kit and then connect

blue wire from light pan to black wire

from LED light kit.

Attach LED light kit onto the light pan,

aligning the keyhole slots on the LED light

kit with the preassembled screws on the

light pan. Twist clockwise till lock.

Reinstall the screw which was just

removed. Tighten all screws securely.

Attach glass by locating dimples in light

pan with grooves on the glass and twist

clockwise until tight.

Plate on motor

Light pan

LED light kit

Blade

Glass

Blue

White

White Black

REMOTE CONTROL SETTING (Dimming/Non Dimming)

Dimming Non Dimming Setting

The remote controller is set with dimming function at

factory.

The “DIM” selection is the light dimmable selection.

If you would make the light with on/off feature, switch it

to ON/OFF position.

The “ON/OFF” selection to make light ON/OFF only (non

dimming function) (Fig. 1 )

Caution: If the remote receiver has been wired with fan,

turn power off by wall switch before switch “DIM” and

“ON/OFF” selection.

DIM

ON/OFF

Fig. 1

Wall cradle installation

Install Transmitter wall mount cradle with 2 screws provided

as shown in Fig. 2.

Install wall cradle with the direction as shown on back side of

the cradle.

Useful tips:

Take remote transmitter up by pushing it at lower area of the

transmitter.

The remote transmitter can be held on magnetic metal

material by a magnet built in the transmitter.

Back side of the

wall mount cradle

Fig. 2

Tips for end users

1. If your fan is operated automatically after installation and power on, it is because your fan is still memorize the previous

setting at factory. Make learn function setting and your fan will be ready for use.

2. If fan or light isn’t working, reset power (turn the power off for at least 5 seconds and then turn the power back) and redo the

learn function setting.

3. It is not available to separately operate the remote setting for more than one fan in the same room (in the area where remote

signal can reach to) if they share the same power supply. Separate power supplies (like as using individual wall switches for each

fan and turn power off for the fan while you are making learn function for other fan) is required if you want to separately control

more than one fan in same room.

4. There might be other remote transmitters got the same code combination as the transmitter that you are using, you may

remove the code setting of the other transmitters by turn the power off and turn it back and then push and hold the “OFF” button

of the transmitter which you are using for at least 10 seconds. You must press the ‘OFF” button within 60 seconds of restoring

power to the fan.

REMOTE CONTROL SETTING and OPERATION

2. Learn function setting, Restore power source to your fan, press and

hold the “OFF” button for at least 4 seconds. You must press the ‘OFF” button

within 60 seconds of restoring power to the fan. (Fig. 4)

Note: If the fan is installed with light (down light), light will twinkle twice then

off. The remote control setting process is complete and your fan is ready for

use. For fans without light, check operation using remote transmitter.

Note: If you want to control the fan with another transmitter, make the same

setting. A fan can be controlled by 2 transmitters maximum.

Note: If the power is on already, you must turn the power off, and then turn

the power back for remote control learn function setting.

Note: If you press wrong buttons, you must again turn power off and turn the

power back then reset learn function.

Transmitter Operation

1. Remove the battery seat from the bottom of remote control

transmitter and install battery. Replace the battery seat. (Fig. 3)

Note

: Use a 3V battery. The battery will weaken with age and should be

replaced before leaking as this will damage the transmitter. Dispose of used

battery properly, keep the battery out of reach for children.

Useful tips

Remove battery seat by pushing at “A” position as shown in Fig. 3 toward to

right hand side and pull it out. Install CR2032 battery into battery seat (make

sure the side with “+” is upward) and reinstall the battery seat.

Back side of

transmitter

A Fig. 3

Fig. 4

“OFF”

REMOTE CONTROL SETTING and OPERATION

Press the button to get desired fan speed, Low to High and then High to Low

cyclically.

Press the OFF button to turn fan off. Fan speed will maintain last setting if

turned off.

Press this forward/reverse button to get desired airﬂow direction. Fan must be

running to reverse. It will take about 25 seconds for fan to slow down and

change rotation direction.

Light control button. Press this button quickly to turn light on or off. To dim

light, hold down the button, the light will cycle from bright to dim to bright until

button is released when the receiver is set at “DIM” position. Light will maintain

last setting if turned off.

Note

: Dimming function is not available if the dimming (DIM) and non dimming

(ON/OFF) switch in receiver is set at ON/OFF position.

Useful tips

LED indicator against fan speeds, Fan off, Low speed,

Medium speed, Medium high speed and High speed. Fig. 5

The buttons on the remote control transmitter control the fan speed and light

as follows. (Fig. 5)

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO

CONDITIONS. (1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT

ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Trouble Shooting

or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,

installation, please call our Customer Service Center at the

number printed on your parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be

locked, securely fasten a prominent warning device, such as a tag, to the service panel.

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

CAUTION: Make sure main power is turned off.

either way. Fan will not operate when switch is in the middle.

4.If this fan uses remote controller, make sure dip switches are setting properly and make

sure battery is effective.

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

CAUTION: Make sure main power is turned off before entering switch housing.

4.Check to be sure light bulb is tight in socket and not touching the glass shade.

5.Some fan motors are sensitive to signals from Solid State variable speed controls.

6.Allow "break-in" periodof 24 hours. Mostnoises associated with a new fan will disappear

after this period.

1.If this is a downrod mount fan, make sure the ridge on mounting bracket engages the

notch in the downrod ball.

2.Make sure that canopy, mounting bracket or mounting plate are tightened securely to

4.Check that all blade holders are tightened securely to motor.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the blades. Measure this distance

from blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade

is positioned for measurement. Repeat for each blade. If all blade levels are not equal,

you can adjust blade levels by the following procedure. To adjust a blade tip down, insert

a washer (not supplied) between the blade and blade holder at the screw closest to the

motor. To adjust a blade tip up, insert washer (not supplied) between the blade and blade

holder at the two screws farthest from the motor. Reverse the position of the washer if

blades mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can

redistribute the weight and possibly result in smoother operation.

1.Check blue wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulb and make sure bulb is tight in socket.

5.Remove light kit and check the plug connections if they are present.

6.If this fan uses remote controller, make sure dip switches are setting properly and make

sure battery is effective.

CAUTION: Make sure main power is turned off before entering switch housing and/or

canopy.

2. If fan sounds noisy:

3. If fan wobbles:

4. If light does not work:

1. If fan does not start:

Trouble Suggested Remedy

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 5MMR54 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MNLR72 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CU52WH Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DS34 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ADR60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3RZHR44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ED56WAD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Maverick II 3MAVR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5EXR60XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5OR52XXD-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Cupra 3CPR60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4MDR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TF24BS Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3HYR56**D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Diamond 4DDR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DIO52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5PR52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TF24 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5RDR Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3DIR58 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MX series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company AC-572LF2000 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5SI Series Fan Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung