Monte Carlo Fan Company 3BTR54 Series Gebrauchsanweisung

Owner’s Guide and Installation Manual

Total fan weight with light kit

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

Attach sales receipt to this card and retain as yourproof of purchase

To register your fixture, please visit our website www.montecarlofans.com

3BTR54XXXXD Series Fan

CUL Model NO. : 3BTR54XXXXD

9.9 kgs

21.8 lbs

Cautions and Warnings

Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with applicable codes and standards (ANSI/NFPA

70), including ﬁre-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be

turned upward and pushed carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet

from the ﬂoor to the trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of

15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.

CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to the

building structure (or the ceiling joist).

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do

not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of ﬁre or electric shock, this fan must be installed with an isolating wall control/switch.

WARNING: To reduce the risk of ﬁre or electric shock, this fan should only be used with fan speed control part no. UC7067RAI manufac-

tured by Rhine Electronic Co., Ltd.

WARNING: To reduce the risk of ﬁre or electric shock, do not use this fan with any other solid state fan speed control device, or variable

speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airﬂow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating

equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the

American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

All set screws must be checked and tightened where necessary before installation.

Note: Suitable for use in wet locations when installed in a GFCI protected branch circuit.

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

1 2 3

4 5 6

OFF

Before you begin installing the fan, Switch

power off at Service panel and lock

service disconnecting means to prevent

power from being switched on

accidentally. When the service

disconnecting means cannot be locked,

securely fasten a warning device, such

as a tag, to the service panel.

Use AC 120V/60HZ power supply

only.

Before installing this fan make sure the

outlet box is properly installed to the

house structure. To reduce the risk of

ﬁre, electric shock, or personal injury,

mount to outlet box or supporting system

acceptable for fan support.

(Mounting must support at least 35 lbs.)

Use metal outlet box suitable for fan

support and use only the screws provided

with the outlet box (must support 35

lbs). Before attaching fan to outlet box,

ensure the outlet box is securely fastened

by at least two points to a structural

ceiling member ( a loose box will cause

the fan to wobble). Remove the two outlet

box screws provided with the box,

aligning the holes of the mounting

bracket with the holes of the outlet box.

Reinstall the 2 outlet box screws

securely.

Partially loosen downrod set screws from

yoke at top of motor assembly.

Remove preassembled cross pin and

keeper pin from downrod. Keep parts.

Remove 4 set screws from yoke cover

and partially install decorative plates onto

the yoke cover with the 4 set screws,

corresponding with the installation step 8.

Note: Make sure to tighten the set

screws when the decorative plates are in

position and ﬁxed with decorative screws

in the installation step 8.

Place downrod over canopy and yoke

cover. Thread lead wires and safety cable

from motor assembly through downrod.

Mounting bracket

Downrod

Cross pin

Keeper pin

Yoke cover

Decorative plate Downrod

Canopy

Yoke cover

7 8 9

10 11 12

Slip downrod into motor housing yoke,

aligning holes and install cross pin and

keeper pin.

Insert cross pin through yoke and downrod

until point appears on the other side, and

insert keeper pin on cross pin.

Pull the downrod up tight against the

cross pin, and then evenly tighten the

downrod set screws on motor housing

yoke.

Warning: Cross pin and keeper pin must

be installed securely, failure to install them

will result in serious injury.

Remove the decorative set screws. Keep

the set screws.

Place yoke cover on top housing of fan.

Align the slots of the decorative plates with

the screw holes on fan housing and ﬁx them

with the decorative setscrews.

Note: Tighten the set screws on yoke

cover with the decorative plate.

Install ball end of downrod into mounting

bracket opening. Align (engage) slot on

ball with tab on mounting bracket.

Warning: Failure to align slot on ball with

tab may result in serious injury.

Important: If using the angle mount,

make sure open end of mounting bracket

is installed facing the higher point of the

ceiling and make sure the ceiling angle is

not steeper than 30º.

For Canadian installation and for USA fan

and light kit combinations over 35 lbs, in

both ﬂush and downrod modes the safety

cable must be installed into the house

structure beams using 3” lag screws,

washers and lock washers provided.

Make sure that when the safety cable is

fully extended the lead wires are longer

than the cable and no stress is placed on

the lead wires.

Note: If Installing The Secondary Support

Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box.

Make wiring connections using wire

connectors provided as indicated above.

White from fan to White from remote

marked N. Black from fan to Black from

remote marked L. Blue from fan to Blue

from remote marked FOR LIGHT. White

from house to White from remote marked

AC IN N. Black from house to Black from

remote marked AC IN L. Connect all

green grounded wires to Grounded wire

from House. Make sure that no ﬁlaments

are outside of the wire connectors.

Insert the remote receiver into mounting

bracket. Refer to page 7 for receiver

setting.

After making the wire connections, the wires

should be spread apart with the grounded

conductor and the equipment-grounding

conductor on one side of the outlet box and

ungrounded conductor on the other side of

the outlet box. The splices after being made

should be turned upward and pushed carefully

up into the outlet box.

Cross pin

Keeper pin

Yoke cover

Decorative setscrew

Decorative plate

Tab

Slot

SAFETY CABLE INSTALLATION

Lag screw

Safety cable

Washer

Lock washer

Wall switch

Black

(Live)

White

(Neutral)

Ground/Green

White

Black

Blue

Receiver

Power source

Grounded

wires Ungrounded

wires

13 14 15

16 17 18

Lift Canopy allowing the 2 studs to protrude

through the canopy.

Install knurled nuts as shown. Tighten the

knurled nuts securely. The canopy should

adjust for any irregularity in the ceiling or

Outlet box.

Make sure the studs protruding from the

bottom of the Mounting bracket are installed

with threads all the way through the bracket.

Loosen 2 and remove 1 preassembled

screw from the plate on motor. Save

screw for later use.

Connect white wire from fan to white wire

from LED light ﬁxture and then connect

blue (or black) wire from fan to black (or

blue) wire from LED light ﬁxture.

Attach light pan onto the plate on motor,

aligning the keyhole slots on the light pan

with the preassembled screws on the

plate. Twist clockwise till lock.

Reinstall the screw. Tighten all screws

securely.

Remove 3 set screws from light pan.

Keep screws.

Attached inner shade onto the light pan.

Align the holes on inner shade with the

screw holes on the light pan.

Install it onto the light pan with 3 set

screws removed in the installation step

17.

Insert blade into the slot on ﬂywheel.

Install blade with screws and washers

provided, aligning each of the holes as

shown and tighten all screws securely.

Repeat this process for remaining blades.

Note: Make sure the side with a label

“This side up” is installed upward.

Stud

Blade

Plate on motor

Light pan with

LED light ﬁxture

Inner shade

Light pan

This side up

19 20 21

Remove 3 set screws from outer area of

the light pan. keep screws.

Attached decorative frame onto the light

pan. Align the holes on decorative frame

with the screw holes on the light pan.

Install it onto the light pan with 3 set

screws removed in the installation step

19.

Attach the outer shade by locating

dimples in the light pan with grooves on

the glass and twist clockwise until tight.

Outer shade

Decorative frame

REMOTE CONTROL SETTING (Dimming/Non Dimming)

Dimming Non Dimming Setting

The remote controller is set with dimming function at

factory.

The “DIM” selection is the light dimmable selection.

If you would make the light with on/off feature, remove

the rubber plug from the receiver and switch it to

ON/OFF position. Replace the rubber plug.

The “ON/OFF” selection to make light ON/OFF only

(non-dimming function) (Fig. 1 )

Caution: If the remote receiver has been wired with fan,

turn power off by wall switch before switch “DIM” and

“ON/OFF” selection.

DIM

ON/OFF

Fig. 1

Wall cradle installation

Install Transmitter wall mount cradle with 2 screws provided

as shown in Fig. 2.

Install wall cradle with the direction as shown on back side of

the cradle.

Useful tips:

Take remote transmitter up by pushing it at lower area of the

transmitter.

The remote transmitter can be held on magnetic metal

material by a magnet built in the transmitter.

Back side of the

wall mount cradle

Fig. 2

Rubber plug

Tips for end users

1. If your fan is operated automatically after installation and power on, it is because your fan is still memorize the previous

setting at factory. Make learn function setting and your fan will be ready for use.

2. If fan or light isn’t working, reset power (turn the power off for at least 5 seconds and then turn the power back) and redo the

learn function setting.

3. It is not available to separately operate the remote setting for more than one fan in the same room (in the area where remote

signal can reach to) if they share the same power supply. Separate power supplies (like as using individual wall switches for each

fan and turn power off for the fan while you are making learn function for other fan) is required if you want to separately control

more than one fan in same room.

4. There might be other remote transmitters got the same code combination as the transmitter that you are using, you may

remove the code setting of the other transmitters by turn the power off and turn it back and then push and hold the “OFF” button

of the transmitter which you are using for at least 10 seconds. You must press the ‘OFF” button within 60 seconds of restoring

power to the fan.

REMOTE CONTROL SETTING and OPERATION

2. Learn function setting, Restore power source to your fan, press and

hold the “OFF” button for at least 4 seconds. You must press the ‘OFF” button

within 60 seconds of restoring power to the fan. (Fig. 4)

Note: If the fan is installed with light (down light), light will twinkle twice then

off. The remote control setting process is complete and your fan is ready for

use. For fans without light, check operation using remote transmitter.

Note: If you want to control the fan with another transmitter, make the same

setting. A fan can be controlled by 2 transmitters maximum.

Note: If the power is on already, you must turn the power off, and then turn

the power back for remote control learn function setting.

Note: If you press wrong buttons, you must again turn power off and turn the

power back then reset learn function.

Transmitter Operation

1. Remove the battery seat from the bottom of remote control

transmitter and install battery. Replace the battery seat. (Fig. 3)

Note

: Use a 3V battery. The battery will weaken with age and should be

replaced before leaking as this will damage the transmitter. Dispose of used

battery properly, keep the battery out of reach for children.

Useful tips

Remove battery seat by pushing at “A” position as shown in Fig. 3 toward to

right hand side and pull it out. Install CR2032 battery into battery seat (make

sure the side with “+” is upward) and reinstall the battery seat.

Back side of

transmitter

A Fig. 3

Fig. 4

“OFF”

REMOTE CONTROL SETTING and OPERATION

Press the button to get desired fan speed, Low to High and then High to Low

cyclically.

Press the OFF button to turn fan off. Fan speed will maintain last setting if

turned off.

Press this forward/reverse button to get desired airﬂow direction. Fan must be

running to reverse. It will take about 25 seconds for fan to slow down and

change rotation direction.

Light control button. Press this button quickly to turn light on or off. To dim

light, hold down the button, the light will cycle from bright to dim to bright until

button is released when the receiver is set at “DIM” position. Light will maintain

last setting if turned off.

Note

: Dimming function is not available if the dimming (DIM) and non dimming

(ON/OFF) switch in receiver is set at ON/OFF position.

Useful tips

LED indicator against fan speeds, Fan off, Low speed,

Medium speed, Medium high speed and High speed. Fig. 5

The buttons on the remote control transmitter control the fan speed and light

as follows. (Fig. 5)

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO

CONDITIONS. (1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT

ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Trouble Shooting

or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,

installation, please call our Customer Service Center at the

number printed on your parts list insert sheet.

Warning

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be

locked, securely fasten a prominent warning device, such as a tag, to the service panel.

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

CAUTION

either way. Fan will not operate when switch is in the middle.

4.If this fan uses remote controller, make sure dip switches are setting properly and make

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

CAUTION

4.Check to be sure light bulb is tight in socket and not touching the glass shade.

5.Some fan motors are sensitive to signals from Solid State variable speed controls.

6.Allow "break-in" periodof 24 hours. Most noisesassociated with a new fan will disappear

after this period.

1.If this is a downrod mount fan, make sure the ridge on mounting bracket engages the

notch in the downrod ball.

2.Make sure that canopy, mounting bracket or mounting plate are tightened securely to

4.Check that all blade holders are tightened securely to motor.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the blades. Measure this distance

from blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade

is positioned for measurement. Repeat for each blade. If all blade levels are not equal,

you can adjust blade levels by the following procedure. To adjust a blade tip down, insert

a washer (not supplied) between the blade and blade holder at the screw closest to the

motor. To adjust a blade tip up, insert washer (not supplied) between the blade and blade

holder at the two screws farthest from the motor. Reverse the position of the washer if

blades mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can

redistribute the weight and possibly result in smoother operation.

If the above steps do not eliminate the wobble problem, you will need to dynamic balance

your fan with balancing kit provided.

1.Check blue wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulb and make sure bulb is tight in socket.

5.Remove light kit and check the plug connections if they are present.

6.If this fan uses remote controller, make sure dip switches are setting properly and make

CAUTION: Make sure main power is turned off before entering switch housing and/or

canopy.

2. If fan sounds noisy:

3. If fan wobbles:

4. If light does not work:

1. If fan does not start:

Trouble Suggested Remedy

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 5PE56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Ceiling Fans Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HM52 ND Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5SRR54XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MGMR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3STR60 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3VLR60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Jovie 3JVR58 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3JVR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TAR56 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LLR56 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Linden 3LD48 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 14PRR62XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CU52WH Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HS42 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MAVR99XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HS52 D-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3VTR52D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WFXX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LDDC52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DI52WHD-L Fehlerbehebungshandbuch

Monte Carlo Fan Company

Monte Carlo Fan Company 5ATR56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LOR52BSD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3OWR60D Series Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung