Monte Carlo Fan Company 4LMR56 D Series Gebrauchsanweisung

Total fan weight with light

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

Attach sales receipt to this card and retain as yourproof of purchase

To register your fixture, please visit our website www.montecarlofans.com

4LMR56XXXD Series Fan

cETL Model NO. : 4LMR56XXXD

7.4 kg

16.28 lbs

Owner’s Guide and Installation Manual

Cautions and Warnings

Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with applicable codes and standards (ANSI/NFPA 70), including

ﬁre-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side

of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be turned upward and pushed

carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to

prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the ﬂoor

to the trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of 15.9 kg (35 lbs)

or less” And Use Mounting Screws Provided With The Outlet Box.

CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Remove Knockouts

In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to the building structure (or the

ceiling joist).

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert

foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of ﬁre or electric shock, this fan should only be used with fan speed control part no. JY1126R manufactured by Satellite

Electronic ( Zhongshan ) Ltd.

WARNING: To reduce the risk of ﬁre or electric shock, do not use this fan with any other solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airﬂow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment

manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for

Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

CAUTION: The light source is designed for this speciﬁc application and can overheat if serviced by untrained personnel. If any servicing is required, the

product should be returned to an authorized service facility for examination or repair.

All set screws must be checked and tightened where necessary before installation.

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

1 2 3

4 5 6

OFF

Before you begin installing the fan, Switch

power off at Service panel and lock

service disconnecting means to prevent

power from being switched on

accidentally. When the service

disconnecting means cannot be locked,

securely fasten a warning device, such

as a tag, to the service panel.

Use AC 120V/60HZ power supply

only.

Before installing this fan make sure the

outlet box is properly installed to the

house structure. To reduce the risk of

ﬁre, electric shock, or personal injury,

mount to outlet box or supporting system

acceptable for fan support.

(Mounting must support at least 35 lbs.)

Remove decorative ring from canopy by

turning counterclockwise.

Partially loosen 2 of the set screws on

mounting bracket corresponding to the slotted

holes on the canopy upper ring. Remove the

other 2 set screws. Save screws.

Use metal outlet box suitable for fan

support and use only the screws provided

with the outlet box (must support 35

lbs). Before attaching fan to outlet box,

ensure the outlet box is securely fastened

by at least two points to a structural

ceiling member ( a loose box will cause

the fan to wobble). Remove the two outlet

box screws provided with the box,

aligning the holes of the mounting

bracket with the holes of the outlet box.

Reinstall the 2 outlet box screws

securely.

Partially loosen downrod set screws from

yoke at top of motor assembly.

Remove preassembled keeper pin and

cross pin from downrod. Keep parts

Place downrod over canopy, canopy ring

and yoke cover. Thread lead wires and

safety cable from motor assembly

through downrod.

Yoke cover

Mounting bracket

Downrod

Cross pin

Keeper pin

Canopy ring

Canopy

Mounting bracket

Canopy ring

Yoke

Canopy

7 8

Slip downrod into motor housing yoke,

aligning holes and install cross pin and

keeper pin.

Insert cross pin through yoke and downrod

until point appears on the other side, and

insert keeper pin on cross pin.

Pull the downrod up tight against the

cross pin, and then evenly tighten the

downrod set screws on motor housing

yoke.

Place yoke cover on top housing of fan.

Warning: Cross pin and keeper pin must

be installed securely, failure to install them

will result in serious injury.

Install ball end of downrod into mounting

bracket opening. Align (engage) slot on

ball with tab on mounting bracket.

Warning: Failure to align slot on ball with

tab may result in serious injury.

Important: If using the angle mount,

make sure open end of mounting bracket

is installed facing the higher point of the

ceiling and make sure the ceiling angle is

not steeper than 20º. Longer downrod

may be necessary allowing the fan blades

to rotate without obstructions.

For Canadian installation and for USA fan

and light kit combinations over 35 lbs, in

both ﬂush and downrod modes the safety

cable must be installed into the house

structure beams using 3” lag screws,

washers and lock washers provided.

Make sure that when the safety cable is

fully extended the lead wires are longer

than the cable and no stress is placed on

the lead wires.

Note: If Installing The Secondary Support

Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box.

Make wiring connections using wire connectors provided as indicated above.

Brown wire from fan to Brown wire from receiver marked Motor U.

Gray wire from fan to Gray wire from receiver marked Motor V.

Thinner blue wire from fan to Blue wire from receiver marked Motor W.

White wire from fan marked “For light” to White wire from receiver marked “For light”.

Thicker blue wire from fan marked “For light” to Blue wire from receiver marked “For light”.

White (Neutral) wire from house to White wire from remote marked AC IN N.

Black (Live) wire from house to Black wire from remote marked AC IN L.

Connect all green grounded wires to Grounded wire from House.

Make sure that no ﬁlaments are outside of the wire connectors.

Insert the remote receiver into mounting bracket.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding

conductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices after being

made should be turned upward and pushed carefully up into the outlet box.

Tab

Slot

SAFETY CABLE INSTALLATION

Lag screw

Safety cable

Washer

Lock washer

Cross pin Keeper pin

White Blue White

Black

Receiver

Blue

Grey

Brown

Ground/Green

White

Black

Wall

Power source

switch

11 12 13

14 15 16

Lift Canopy, aligning the key holes with

the preinstalled screws on canopy and

turning clockwise till tight, and then

reinstall the set screw removed in step 3.

Install canopy ring by locating its groove

with the screws on canopy and turn

clockwise till tight.

Loosen 2 and remove 1 preassembled

screw from the plate on motor. Save

screw for later use.

Attach light pan onto the plate on motor,

Place light pan over the lead wires from

fan, aligning the keyhole slots on the light

plate with the preassembled screws on

the plate. Twist clockwise till lock.

Reinstall the screw removed in step 13.

Tighten all screws securely.

Loosen 2 and remove 1 preassembled

screw from light pan. Save screw for later

use.

Remove nut, rubber washer, hex nut and

ﬁnial from LED light ﬁxture. Keep parts

Insert blade into the slot on ﬂywheel.

Install blade with a blade supporting plate

by the screws provided, aligning each of

the holes as shown and tighten all screws

securely. Repeat this process for

remaining blades.

Note: Make sure the side with a label

“This side up” is installed upward.

Groove

Light pan

Blade

Blade supporting plate

Plate on motor

Nut

Finial

Rubber washer

Hex nut

This side up

Este lado haciaarriba

Haut

This side up

17 18 19

Connect white wire from fan to white wire

from LED light kit and then connect blue

(or black) wire from fan to black (or blue)

wire from LED light ﬁxture.

Attach LED light ﬁxture onto the light pan,

aligning the keyhole slots on the light

ﬁxture with the preassembled screws on

the light pan and twist clockwise till lock.

Reinstall the screw removed in step 15.

Tighten all screws securely.

Raise outer light shade, aligning threaded

rod on light ﬁxture with the hole in middle

of the light shade and push up gently

allowing threaded rod to come through

the hole. Install a hex nut and ﬁnial with a

rubber washer to ﬁx the light shade as

shown in illustration. DO NOT OVER

TIGHTEN the hex nut and ﬁnial as glass

may crack or break.

Align the hole on inner light shade with

the threaded rod on light ﬁxture and

attached it onto light ﬁxture with a nut.

DO NOT OVER TIGHTEN the nut.

Inner light shade

LED light

ﬁxture

Nut

Outer light shade

Finial

Hex nut

Rubber washer

Remote Controller Operation

Remove the battery cover from the remote control transmitter and install

batteries. Replace the cover. This remote uses 2 1.5V/AAA batteries.

Note: If not using for long periods of time, remove battery to prevent

damage to remote transmitter, and store the remote transmitter away from

excess heat or humidity

Dimming, Non Dimming Setting (Only available for fans with light)

In the dimming mold, it is a light dimming selection and it is to be used with

dimmable luminaries. The remote controller is set with dimming function at

factory.

In ON/OFF (non-dimming mold), it is for light ON/OFF only (non-dimming

function).

Learn Function Setting

Restore power to your fan, press and hold the “SET” button to pair the

Transmitter and receiver. You must press the ‘SET” button with in 60 seconds

of restoring power to the fan.

Note:

Fan will operate at minimum speed and light will blinks after the setting.

Note

: If the power is on already, you must turn the power off then turn the

power back for remote control setting.

Battery cover

DIM (D)

ON/OFF (O)

SET

The buttons on the remote control transmitter control the fan speed and light as follows.

Fan speed

1 = minimum speed 2 = low speed 3 = medium low speed

4 = medium speed 5 = medium high speed 6 = high speed

This button turns the fan off.

Forward/Reverse button- This button is to control direction of fan rotation. Press once

to change direction of the fan rotation. Fan must be running to reverse.

Light button- Press this button to turn light on or off.

Light button- Press this button to desired brightness, dim to bright.

Light button- Press this button to desired brightness, bright to dim.

Breeze-

Press the Breeze button, fan will operates at high speed (6th) for 30 seconds, then automatically

change to 5th, 4th, 3rd, 2nd, 1st at intervals of 30 seconds, and then change it from Low speed (1st) to

2nd, 3rd, 4th, 5th, 6th repeat the cycle until the breeze mold is cancelled.

Breeze mold can be erase by pressing the buttons of power or speed control.

Note

: This remote controller has auto resume function, the fan and light will maintain the last setting if

turned off with exception of the Breeze mold.

SET

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO

CONDITIONS. (1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT

ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

The receiver provides the following protective functions

Lock protection- The DC motor has a build-in safety feature

against blade obstruction during operation. If something

obstructs the fan blades, the motor will stop operation after

about 20 seconds of interruption. Please remove obstacles

and reset it by turning the power off, and turn it back.

Over 40W protection- When the receiver detects motor

power consumption which is greater than 40W, the fan RPM

will be lowered to protect it from overloading.

Tips for end users

1. If your fan is operated automatically after installation and power on, it is because your fan is still memorize the previous

setting at factory. Make Remote control setting (learn function) and your fan will be ready for use.

2. If fan or light isn’t working, reset power (turn the power off then turn the power back) and redo the remote setting.

3. It is not available to separately operate the remote setting for more than one fan in the same room (in the area where remote

signal can reach to) if they share the same power supply. Separate power supplies (like as using individual wall switches for each

fan and turn power off for the fan while you are making learn function for other fan) is required if you want to separately control

more than one fan in same room.

4. When fan is turned on or operated forward/reverse function, it shutters & goes back & forth until it turns. It is a normal

performance of this fan and it will take for few seconds to run this operation.

Install Transmitter wall mount cradle with 2 screws provided.

Useful tips:

Take remote transmitter up by pushing it at lower area of the

transmitter.

The remote transmitter can be held on magnetic metal

materials by a magnet built in the transmitter.

Wall mount cradle

Trouble Shooting

or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,

installation, please call our Customer Service Center at the

number printed on your parts list insert sheet.

Warning

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be

locked, securely fasten a prominent warning device, such as a tag, to the service panel.

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

CAUTION

either way. Fan will not operate when switch is in the middle.

4.If this fan uses remote controller, make sure dip switches are setting properly and make

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

CAUTION

4.Check to be sure light bulb is tight in socket and not touching the glass shade.

5.Some fan motors are sensitive to signals from Solid State variable speed controls.

6.Allow "break-in" periodof 24 hours. Most noisesassociated with a new fan will disappear

after this period.

1.If this is a downrod mount fan, make sure the ridge on mounting bracket engages the

notch in the downrod ball.

2.Make sure that canopy, mounting bracket or mounting plate are tightened securely to

4.Check that all blade holders are tightened securely to motor.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the blades. Measure this distance

from blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade

is positioned for measurement. Repeat for each blade. If all blade levels are not equal,

you can adjust blade levels by the following procedure. To adjust a blade tip down, insert

a washer (not supplied) between the blade and blade holder at the screw closest to the

motor. To adjust a blade tip up, insert washer (not supplied) between the blade and blade

holder at the two screws farthest from the motor. Reverse the position of the washer if

blades mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can

redistribute the weight and possibly result in smoother operation.

If the above steps do not eliminate the wobble problem, you will need to dynamic balance

your fan with balancing kit provided.

1.Check blue wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulb and make sure bulb is tight in socket.

5.Remove light kit and check the plug connections if they are present.

6.If this fan uses remote controller, make sure dip switches are setting properly and make

CAUTION: Make sure main power is turned off before entering switch housing and/or

canopy.

2. If fan sounds noisy:

3. If fan wobbles:

4. If light does not work:

1. If fan does not start:

Trouble Suggested Remedy

Mar.2020

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 3CLNSM60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TAHR56 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5OBR52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5KBR54 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ERAR44 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HV52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Arcade 3ARR68 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5GIR54XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Radial 5RA52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5COM52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5SI Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5BGR56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3BvR52XXd-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5AZR56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4CO28 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3JVR58 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DI52WHD-L Fehlerbehebungshandbuch

Monte Carlo Fan Company

Monte Carlo Fan Company TRAVERSE 5TV52 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AMR60BSD Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3BRYSM60D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5TV52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WCR56XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3NDR54XXD Series Technisches Dokument

Monte Carlo Fan Company

Monte Carlo Fan Company 3RULSM52HABD Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung