Monte Carlo Fan Company 5TV52 D Series Gebrauchsanweisung

Owner’s Guide and Installation Manual

Attach sales receipt to this card and retain as your proo o purchase

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

To register your ixture, please visit our website www.montecarlo ans.com

5TV52XXD Series Fan

Total an weight with light kit

UL Model No. : 5TV52

10.6 kgs

23.4 lbs

WAR I G: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR I JURY TO PERSO S, OBSERVE THE FOLLOWI G

READ A D SAVE THESE I STRUCTIO S

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (A SI/ FPA 70-1999), including

fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the

outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be turned upward and pushed carefully up

into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent

power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a

tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to the

trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of

15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.

CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do ot Re-

move Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to

the building structure (or the ceiling joist).

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign

object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.

WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

ever place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment manufac-

turer’s guideline safety standards such as those published by the ational Fire Protection Association ( FPA), and the American Society for Heating, Refrigera-

tion and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

All set screws must be checked and tightened where necessary before installation.

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlo ans.com

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,

Stepladder and Wire Strippers.

Before you begin installing the fan, witch power off

at ervice panel and lock service disconnecting

means to prevent power from being switched on ac-

cidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent warn-

ing device, such as a tag, to the service panel.

Before installing this fan make sure the outlet

box is properly installed to the house structure.

To reduce the risk of fire, electric shock, or per-

sonal injury, mount to outlet box or supporting

system acceptable for fan support.

(Mounting must support at least 35 lbs.)

Thread safety cable through center

hole of the mounting plate. Thread

your house wires through center hole

also.These will be needed for wiring

of the fan.

ecurely attached the mounting plate

to the outlet box using two screws

supplied by the outlet box. se

metal outlet box suitable for fan

support (must support 35 lbs).

Place the decorative ring on the

motor housing.

Make wire connections to power source using

wire nuts provided. Make sure that no filiments

are outside of the wirenut. After making the

wire connections, the wires should be spread

apart with the grounded conductor and the

equipment-grounding conductor on one side of

the outlet box and ungrounded conductor on the

other side of the outlet box.

Connect black and blue wire from fan to Black

or (Hot) wire from house. Connect White wire

from Fan to White (Neutral) wire from house.

Connect Ground leads from mounting bracket

and downrod to Ground lead from house.

Refer to Safety Tips section of manual.

Carefully lift the fan motor assembly

and engage the slot in the motor

housing with the hook on the mount-

ing plate so that the motor is se-

curely suspended.

For Canadian installation and for U A fan and

light kit combinations over 35 lbs, in both flush

and downrod mode the safety cable must be in-

stalled into the house structure beams using the

3” lag screws provided. Make sure that when

the safety cable is fully extended the leadwires

are longer than the cable and no stress is placed

on the leadwires. Note:If Installing The econd-

ary upport afety Cable in the U. ., Do Not Re-

move Knockouts In The Outlet Box.

5afety cable installation

Safety Cable

Lag Screw

Safety Cable

Washer

Lock Washer

Lift the motor housing up aligning the L

shape holes with the screws and

washers on the mounting plate. Turn the

housing clockwise to hold in position. In-

stall the other two screws and washers

previously removed securely.

Loosen the two screws and washers

across from each other on the ridge

of the mounting plate. Remove the

other two screws and lock washers.

ave for later use.

Lift the decorative ring up and twist

clockwise till tight.

Check the motor for shipping stabiliz-

ers and remove if present. Attach

blades using screws and washers in

hardware pak. Tighten screws se-

curely.

Loosen 2 screws and remove 1 screw

from motor plate. ave removed

screw for use later.

Connect plug from fan to switch

house plug.

Install by twisting clockwise, add 1

screw removed step 14 to switch

housing plate. Tighten the 3 screws

securely.

Connect white wire from fan to white

wire from light fixture. Then plug

blue wire from fan to black wire from

light fixture.

Loosen the pre installed screws of

switch housing plate.

Install 3 screws to install light pan.

For fan with light kit go

to step 20-21 to

finish.

For fan without light kit

go to step 22.

Attach glass by locating dimples in

light fixture with the groves in glass

and twisting clockwise till tight.

Attach the non light cover by locating

dimples in the light fixture with the

grooves in the non light kit cover and

twist clockwise till tight. WARNING:

Make sure light bulb is not installed

when using this cover.

Install 75 watt halogen bulb. Do not touch

bulb surface as oily residue from skin can

cause the bulb to explode. Bulb Included.

WARNING: Over lamping the fan

will result in the fan lights shut-

ting down until the proper

wattage of bulbs are installed.

Reset the lights by turning off the

wall switch, breaker,or by remote.

Replace bulbs with the correct

wattage bulbs, turn the power on.

2. If fan sounds noisy:

1. If fan does not start:

3. If fan wobbles:

4. If light does not work:

Trouble hooting

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, instal-

lation, or wiring. In some cases, these installation errors may be mistaken for defects. If you experi-

ence any faults, please check this Trouble hooting Chart. If a problem cannot be remedied, or you are

experiencing difficulty in installation, please call our Customer ervice Center at the number printed on

your parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock serv-

ice disconnecting means to prevent power from being switched on accidentally. When the

service disconnecting means cannot be locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

Trouble Suggested Remedy

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

3.Check to make sure the dip switches from the transmitter and receiver are set on the

same frequency.

CA TION: Make sure main power is turned off

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are

tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against

each other or against the interior wall of the switch housing.

CA TION: Make sure main power is turned off before entering switch hous-

ing.

4. ome fan motors are sensitive to signals from olid tate variable speed controls.

DO NOT SE a Solid State variable speed control.

5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disap-

pear after this period.

1.If this is a downrod mount fan, make sure the ridge on mounting bracket engages the

notch in the downrod ball.

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junc-

tion box and junction box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level

by selecting a point on the ceiling above the tip of one of the blades. Measure this dis-

tance from blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the

next blade is positioned for measurement. Repeat for each blade. If all blade levels are

not equal, you can adjust blade levels by the following procedure. To adjust a blade tip

down, insert a washer (not supplied) between the blade and blade holder at the screw

closest to the motor. To adjust a blade tip up, insert washer (not supplied) between the

blade and blade holder at the two screws farthest from the motor. Reverse the position

of the washer if blades mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades

can redistribute the weight and possibly result in smoother operation.

1.Check wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

CA TION: Make sure main power is turned off before entering switch hous-

ing.

WARNING: Over lamping the fan will result in the fan lights shutting down

until the proper wattage of bulbs are installed. Reset the lights by turning off

the wall switch, breaker,or by remote. Replace bulbs with the correct wattage

bulbs, turn the power on.

Jan.2012 Update customer service phone number

Jun.2013 Update for CUL regulation

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 3IKR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AVLCR54XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3NDR54XXD Series Technisches Dokument

Monte Carlo Fan Company

Monte Carlo Fan Company 3MUR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company MC263 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 8ARR58XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Linden 5LD52 F Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HVDC52D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5RDR Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5GMR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3SY52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5VMR72 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Launceton 56 4LNCR56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MTR38TMO-L Handbuch

Monte Carlo Fan Company

Monte Carlo Fan Company 5HS42XX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 8ATR44XXD-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CE52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MO52 O-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HS42RB Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3VLR60ATIHAB Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AVMR64 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4GIR60ATIHAB Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Colony 5COM52 Series Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung