Monte Carlo Fan Company 3BvR52XXd-L Series Bedienungsanleitung

Owner’s

anual

Ceiling Fan Installation Instructions

57$ &&!,70,8(4

!$"!!" #"!

Total fan weight

with lights

Flush ount -No light kit Downrod with light kit

Flush ount -Light kit Downrod without light kit

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-

1999), including fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on

one side of the outlet box and ungrounded conductor on the other side of the outlet box.

Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being

switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

ake sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from

the floor to the trailing edge of the blade.

To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support.

( ounting must support at least 35 lbs.)

Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

NEVER place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equip-

ment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American

Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched

on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the

service panel.

10.

11.

12.

13.

14.

15.

Installation

% : TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

!"' "!

"! # 

Phillips Screwdriver Wire Cutters Pliers Step Ladder

Before you begin installing the fan, Switch power off

at Service panel and lock service disconnecting means

to prevent power from being switched on accidentally.

When the service disconnecting means cannot be

locked, securely fasten a prominent warning device,

such as a tag, to the service panel.



Before installing this fan make sure the outlet

box is properly installed to the house structure.

To reduce the risk of fire, electric shock, or per-

sonal injury, mount to outlet box or supporting

system acceptable for fan support.

( ounting must support at least 35 lbs.)



572:8/35:49<09/

57<09/5:920./9109.5

9589,6

575<475+35:49

<09/57<09/5:920./9

109.59589,6

Remove the coupler from the

mounting plate by unscrewing 6

screws. Save the yoke and screws

for future use when installing

downrod.



Thread safety cable through center

hole of the mounting plate. Thread

your house wires through center hole

also.These will be needed for wiring

of the fan.



For Canadian installation and for USA fan and

light kit combinations over 35 lbs, in both flush

and downrod mode the safety cable must be

installed into the house structure beams using

the 3” lag screws provided. ake sure that

when the safety cable is fully extended the

leadwires are longer than the cable and no

stress is placed on the leadwires.

Safety cable installation

!(-,9>()2,

(.!*7,<

!(-,9>()2,

%(8/,7

5*1%(8/,7

Carefully lift the fan motor assembly

and engage the slot in the motor

bracket with the hook on the mount-

ing plate so that the motor is secure-

ly suspended.



Aline the clips on the housing with the

holes in the mounting plate



Attach blade to blade bracket using

the screws and washers provided.

Tighten each of the screws securely.

Repeat this process 2 more times.



Attach blade assembly to the motor

and tighen screws securely. Repeat

this process 2 more times.



Loosen 2 screws and remove 1 screw

from motor plate and save.



Align keyslot holes of the switch

housing plate to the holes of the

motor plate and twist to lock. Add

the screw removed from step 16.

Tighten securely.



Remove 3 screws from switch hous-

ing plate. Save the screws for future

use.



Lift the motor bracket so that the

threaded studs on the mounting

plate protrude through the slots in

the motor bracket. Securely tighten

the locknuts onto the threaded

studs.



ake wire connections to power source using wire

nuts provided. ake sure that no filiments are outside

of the wirenut. After making the wire connections, the

wires should be spread apart with the grounded con-

ductor and the equipment-grounding conductor on one

side of the outlet box and ungrounded conductor on

the other side of the outlet box.



ake wire connections as per above diagram.

Connect the white wire from the fan to the

White or Neutral wire from the power source.

Connect the black wire from the fan to the

Black or hot wire from the power source.

Connect all Green / Yellow wires from the fan,

Downrod and mounting bracket to the Ground

wire from the house.



House Fan

Black

White

Green

Black

White

Green(downrod)

Green(Bracket)

Securely attached the mounting

plate to the outlet box using two

screws supplied by the outlet box.

Use metal outlet box suitable for fan

support (must support 35 lbs).



Lift motor housing cover up and turn it

clockwise to hold in position.





Remove finial nut, hex nut, and finial

cap from the fitter.





Install 3 x 40 watt candelabra bulbs.

Bulbs are included.

% Over lamping the fan will

result in the fan lights shutting down

until the proper wattage of bulbs are

installed.

Reset the lights by turning off the wall

switch, breaker,or by remote. Replace

bulbs with the correct wattage bulbs, turn

the power on.

Place glass, finial cap, hex nut, and

finial onto the fitter securely. Disconnect white wire from fan and

white wire from fitter. Disconnect blue

wire from fan and black wire from fit-

ter.



Install the 3 screws previously

removed from step 18.



57-(4<09/5:920./9109

.59589,695

-0408/

57-(4<09/20./9109.5

9589,6

Connect plug from fan to plug from

switch cap..



Remove the double sided sticky tape

and stick the capacitor to the switch

cap plate. Receiver needs to be stuck

to the switch cap plate also by using

2 double sided sticky tapes included.



Remove the switch cap from the fit-

ter.



Remove the hex nut and lock washer

from the switch cap.



Insert the center plastic plug provid-

ed into the center hole of the switch

cap.



Set dip switches on the Remote Transmitter

and Remote Receiver to the same settings.

This must be done so the units will com-

muncate properly. If you have other fans you

can set to control from one transmitter by set-

ting both receivers the same as the transmitter.

If you have more than one fan with remote.

You can set the dip switches to different posi-

tiosns to have seperate control.

Remote

Transmitter

Dip swtiches

Remote Receiver Dip switches

 !,97,359,7,*,0;,725*(9,+

+5<40480+,5--(48<09*/

*(6

The studs on the mounting plate

protrude through the slots in the

motor bracket .Securely tighten the

locknuts onto the threaded studs.



Insert the pin through the yoke and

downrod until the point appears on

the other side.



Insert downrod into yoke. Align the

hole in the downrod with hole in the

yoke.





Use metal outlet box suitable for fan

support (must support 35 lbs).

Before attaching fan to outlet box,

ensure the outlet box is securley fas-

tened by at least two points to a

structural ceiling member ( a loose

box will cause the fan to wabble).

#8,542>9/,8*7,<8675;0+,+

<09/9/,5:92,9)5=



Thread leadwires and safety cable

through the mounting plate.

Loosen the 2 set screws in yoke.



Install the 3 screws previously

removed from step 18.



Connect plug from fan to plug from

switch cap..





Remove the cotter and keeper pins

and save for later use.

Remove the hanger ball by loosening

the setscrew in the hanger ball until

the ball falls freely down the down-

rod. Remove the pin from the down-

rod, then remove the hanger ball.

Save the pin and hanger ball for later

use.





Thread the leadwires through the

downrod as shown.

Install the keeper to pin.



Tighten the 2 set screws on the

yoke once the downrod is in place.



Hold the motor housing and turn mount-

ing plate clockwise by screwdriver to hold

it with housing in position. ake sure

that the clips are engaged with the

mounting plate well.



Place the motor housing on the polyfoam

as shown, then locate the mounting plate

to the housing by aligning the clips on

the housing with holes in the mounting

plate



Clip

Clip in posi-

tion

Thread the lead wires through the

motor housing cover

 

Place motor housing cover over the

mounting plate.

Install motor housing cover to the

mounting plate with 3 screws.



Thread the leadwires through the

canopy and Place the canopy over

the downrod.



Thread the leadwires through the

hanger ball and place onto the

downrod.



Position the pin through the two

holes in the downrod and align the

hanger ball so the pin is captured in

the groove in the top of the hanger

ball. 59,043:89),0489(22,+

<09/+5<475+(4+/(4.,7)(22



Pull the hanger ball up tight against

the pin and securely tighten the

setscrew in the hanger ball. 2558,

8,98*7,<*5:2+*7,(9,-(4

<5))2,



Hang assembled fan to the mounting

bracket installed to ceiling in previous

step.



Fan and light kit combinations over 35 lbs, in

both flush and downrod mode the safety cable

must be installed into the house structure

beams using the 3” lag screws,washers, and

lock washers. provided. ake sure that when

the safety cable is fully extended the leadwires

are longer than the cable and no stress is

placed on the leadwires.

 Safety cable installation

!(-,9>()2,

(.!*7,<

safety

cable

3” lag

screw

lock

washer

ake sure the studs protruding from

the bottom of the mounting bracket

are installed with threads all the way

through the bracket.



Lift canopy up aligning with the

studs from mounting bracket. Install

the 2 thumb nuts to the studs and

finger tighen.



ake wire connections to power source using wire nuts

provided. ake sure that no filiments are outside of

the wirenut. After making the wire connections, the

wires should be spread apart with the grounded conduc-

tor and the equipment-grounding conductor on one side

of the outlet box and ungrounded conductor on the

other side of the outlet box.



ake wire connections as per above diagram.

Connect the white wire from the fan to the

White or Neutral wire from the power source.

Connect the black wire from the fan to the

Black or hot wire from the power source.

Connect all Green / Yellow wires from the fan,

Downrod and mounting bracket to the Ground

wire from the house.



House Fan

Black

White

Green

Black

White

Green(downrod)

Green(Bracket)

59589,695

-0408/0489(22(9054

Remove cover by snaping off from top or bottom.

Remove battery cover. Install 12V battery into

wall remote. Duracell N21 / Eveready A23 / GP

23A all 12V.Attach cover of remote by placing

over buttons and snap the battery cover in place.



Place face plate over battery compartment and

buttons. Place remote over 2 pins on front

cover. Attach cover of remote by placing over 4

pins and snaping into place.

 HAND HELD INSTALL

Attach front cover to wall control with

screws provided. Snap battery cover

in place.



 WALL OUNT INSTALL

,359,549752"7(483099,7,(9:7,8

! Depress “l dot” for low speed, “2 dots” for medium or “3 dots” for

high. To turn fan off press square”.

" To turn light on, press light dimmer once quickly. To turn off

press once quickly while light is on. To dim light hold down button “light dimmer”.

The light will cycle from bright to dim to bright until button is released. Light will

maintain last setting if turned off.

HIGH SPEED

EDIU SPEED

LOW SPEED

FAN OFF SETTING

(Turns fan off only)

LIGHT ON/OFF SET-

TING AND DI ER

(Press and hold to

dim light infinitively)

LED LIGHT

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

3.Check to make sure the dip switches from the transmitter and receiver are set on the same

frequency.

#"(1,8:7,3(0465<,7089:74,+5--

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

#"(1,8:7,3(0465<,7089:74,+5--),-57,,49,704.8<09*//5:804.

4.Some fan motors are sensitive to signals from Solid State variable speed controls.

"#!(!520+!9(9,;(70()2,86,,+*549752

5.Allow "break-in" period of 24 hours. ost noises associated with a new fan will disappear

after this period.

1. ake sure that the ridge of the canopy engages the notch in the downrod ball.

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4. ake sure that canopy and mounting bracket are tightened securely to ceiling junction box

and junction box is mounted firmly to ceiling joist.

5. ost fan wobble problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the blades. easure this distance from

blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade is posi-

tioned for measurement. Repeat for each blade. If all blade levels are not equal, you can

adjust blade levels by the following procedure. To adjust a blade tip down, insert a washer

(not supplied) between the blade and blade holder at the screw closest to the motor. To

adjust a blade tip up, insert washer (not supplied) between the blade and blade holder at the

two screws farthest from the motor. Reverse the position of the washer if blades mount from

top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can

redistribute the weight and possibly result in smoother operation.

1.Check wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

#"(1,8:7,3(0465<,7089:74,+5--),-57,,49,704.8<09*//5:804.

% ,-57,(99,36904.957,62(*,9/,-:8,3(1,8:7,9/,3(0465<,7089:74,+

5--959/,-(4 ,62(*,542><09/((36-:8,:8,080480+,9/,*(456>549/,)2:,

(4+57(4.,<07,8957,359,7,*,0;,6:8/(4+9<0899/,*(69556,49/,-:8,*(8,

2. If fan sounds noisy:

1. If fan does not start:

3. If fan wobbles:

4. If light does not work:

Trouble Shooting

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation,

or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,

please check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty

in installation, please call our Customer Service Center at the number printed on your parts list insert sheet.

%(7404.,-57,8,7;0*04.57*2,(404.:409!<09*/65<,75--(9!,7;0*,6(4,2(4+25*18,7;0*,+08

*544,*904.3,(489567,;,4965<,7-753),04.8<09*/,+54(**0+,49(22>%/,49/,8,7;0*,+08

*544,*904.3,(48*(4459),25*1,+8,*:7,2>-(89,4(675304,49<(7404.+,;0*,8:*/(8(9(.

959/,8,7;0*,6(4,2

"75:)2, !:..,89,+ ,3,+>

Customer Service Center:

301 West Washington St.

Riverside, NJ 08075

1-800-519-4092

www.montecarlofans.com

manuel de

l´utilisateur

Instructions pour l´installation d´un

ventilateur de plafond

Poids total du

ventilateur

LIRE ET GARDER CE IN TRUCTION

Por 3BVR52XXD-L Ventilateurs

Tige avec le kit léger

Tige sans kit léger

Bâti affleurant - kit léger

Bâti affleurant - aucun kit léger

Inhaltsverzeichnis

Sprachen:

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 3MAVR60RZW Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5GL52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5OR52XXD-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MMR54 D-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5TV52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Mach One Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3STMSM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 25003 Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 4SBWR56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5GIR54XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TF24XX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5PEN56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CMR56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DIO52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ED56WAD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 8ARR58XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AVMR64 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ROR Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5TLR54 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ERHR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TAHR56 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MO52XXO-L series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3RULSM52HABD Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3IKR52 Series Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung