Monte Carlo Fan Company 5AGR56 D Series Gebrauchsanweisung

Owner’s Guide and Installation Manual

Attach sal s r c ipt to this card and r tain as your proof of purchas

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

To r gist r your fixtur , pl as visit our w bsit www.mont carlofans.com

5AGR56XXD Series Fan

Total fan w ight with light kit

UL Mod l No. : 5AGR56

11.3 kgs

24.86 lbs

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA

70-1999), including fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be

turned upward and pushed carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

ake sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet

from the floor to the trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, ount To Outlet Box arked “Acceptable for Fan Support of

15.9 kg (35 lbs) or less” And Use ounting Screws Provided With The Outlet Box.

CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Re-

move Knockouts In The Outlet Box. ount the secondary support safety cable through the reserved nail/screw hole on the outlet box to

the building structure (or the ceiling joist).

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do

not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.

WARNING: To reduce the risk of fire or electric shock, this fan should only be used with fan speed control part no. UC7067RC manufac-

tured by Rhine Electronic Co., Ltd.

WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed

control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating

equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the

American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

All set screws must be checked and tightened where necessary before installation.

Custom r S rvic

800-969-3347

Custom r S rvic C nt r

7400 Lind r Av .

Skoki , IL 60077

www.mont carlofans.com

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,

Stepladder and Wire Strippers.

Before you begin installing the fan, Switch

power off at Service panel and lock service dis-

connecting means to prevent power from being

switched on accidentally. When the service dis-

connecting means cannot be locked, securely

fasten a prominent warning device, such as a

tag, to the service panel.

Before installing this fan make sure the outlet box is

properly installed to the house structure. To reduce

the risk of fire, electric shock, or personal injury,

mount to outlet box or supporting system acceptable

for fan support. (Mounting must support at least 35

lbs.)

Use metal outlet box suitable for fan support

and use only the screws provided with the outlet

box (must support 35 lbs). Before attaching fan

to outlet box, ensure the outlet box is securely

fastened by at least two points to a structural

ceiling member ( a loose box will cause the fan

to wobble). Use only the screws provided

with the outlet box.

emove the keeper pin and cross pin

from downrod, and save for later

use.

Place canopy over down rod.

5 6

Place Yoke Cover over down rod.

Thread leadwires and safety cable

through the downrod

Loosen the 2 screws on the yoke to

allow down rod to slip into yoke.

Insert down rod into yoke on top of

the fan body. Align the hole in the

down rod with the hole in the yoke.

Insert the Pin through the yoke and

down rod until the point appears on

the other side.

Set dip switches on the emote Transmitter and emote

eceiver to the same settings. This must be done so the

units will communcate properly. If you have other fans

you can set to control from one transmitter by setting

both receivers the same as the transmitter. If you have

more than one fan with remote. You can set the dip

switches to different positiosns to have seperate control.

emote Transmitter Dip swtiches

emote eceiver Dip switches

Install remote receiver into the

mounting bracket.

Make sure the studs protruding from the

bottom of the Mounting bracket are in-

stalled with threads all the way through

the bracket.

Install keeper pin.

Tighten the 2 set screws on the yoke,

once the down rod is in place.

Hang assembled fan from the mounting bracket in-

stalled to ceiling in previous step. Make sure the fan

is hanging straight. otate fan until the tab on the

Mounting bracket engages the slot on the Downrod

Ball. This must be done to prevent the fan body from

rotating when the blades are in motion.

eady for wiring.

Make wiring connections as indicated above.

White from fan to white from remote marked

N. Blue from fan to blue from remote marked

light. Black from fan to Black from remote

marked L. White from house to white from re-

mote marked AC N . Black from house to Black

from remote marked AC L. Connect all green

ground wires to Grounded wire from House.

For Canadian installation and for USA fan and light

kit combinations over 35 lbs, in both flush and

downrod modes the safety cable must be installed

into the house structure beams using 3” lag

screws, washers and lock washers provided. Make

sure that when the safety cable is fully extended

the lead wires are longer than the cable and no

stress is placed on the lead wires.

Note:If Installing The Secondary Support Safety

Cable in the U.S., Do Not emove Knockouts In

The Outlet Box.

14 Safety cable installation

Safety Cable

Lag Screw

safety

cable

3” lag

screw

lock

washer

Connect white wire from fan to white

wire from light fixture. Then connect

blue wire from fan to black wire from

light fixture.

Align keyslot holes of the light kit

plate and twist to lock. Install screw

removed in step 23 and tighten se-

curely.

Install 3 x 40 watt candelabra base

bulbs, Bulbs included. WA NING:

Over lamping the fan will result

in the fan lights shutting down

until the proper wattage of bulbs

are installed. eset the lights by

turning off the wall switch,

breaker,or by remote. eplace

bulbs with the correct wattage

bulbs, turn the power on.

Attach glass to fan by twisting clock-

wise to lock.

Lift canopy and install knurled nuts as

shown. Tighten the knurled nuts securely.

The canopy should adjust for any irregu-

larity in the ceiling or Outlet box.

Check motor for shipping stabilizers and

remove if present. Insert blades to fan fly-

wheel and place the reinforce plate onto

the blades as shown.

Tighten blade using the screws in hard-

ware pack, repeat this procedure 4 more

times.

Loosen 2 screws and remove one screw.

Keep the removed screw for later use.

Make wire connections to power source using wire nuts

provided. Make sure that no filiments are outside of

the wirenut. After making the wire connections, the

wires should be spread apart with the grounded con-

ductor and the equipment-grounding conductor on one

side of the outlet box and ungrounded conductor on the

other side of the outlet box. The splices after being

made should be turned upward and pushed carefully up

into the outlet box.

Place face plate over battery compartment and

buttons. Place remote over 2 pins on front cover.

Attach cover of remote by placing over 4 pins

and snapping into place. Install wall control unit to outlet box

using machine screws provided.

29 HAND HELD INSTALL WALL MOUNT INSTALL

emove battery cover. Install 12V battery into

wall remote. Duracell MN21 / Eveready A23 / GP

23A all 12V.Attach cover of remote by placing

over buttons and snap the battery cover in place.

Attach front cover to wall control with

screws provided. Snap battery cover

in place.

The reverse feature of this fan is

controlled by a switch located on top

of the fan body. Turn off the fan and

reverse the fan by slipping the

switch. This will reverse the direction

of the Fan blades.

emote Control Transmitter Features:

FAN SPEED Depress “1 dot” for low speed, “2 dots” for medium or “3 dots” for

high. To turn fan off press square”.

LIGHT DIMME To turn light on, press light dimmer once quickly. To turn off

press once quickly while light is on. To dim light hold down button “light dimmer”.

The light will cycle from bright to dim to bright until button is released. Light will

maintain last setting if turned off.

HIGH SPEED

MEDIUM SPEED

LOW SPEED

FAN OFF SETTING

(Turns fan off only)

LIGHT ON/OFF SET-

TING AND DIMME

(Press and hold to

dim light infinitely)

LED LIGHT

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

CAUTION: Make sure main power is turned off.

3.Make sure forward/reverse switch is firmly in up or down position. Fan will not operate when switch

is in the middle.

4.Make sure that shipping stabilizer tabs have been removed from motor.

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each other or

against the interior wall of the switch housing.

CAUTION: Make sure main power is turned off before entering switch housing.

4.Some fan motors are sensitive to signals from Solid State variable speed controls.

5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear after this

period.

1.If this is a downrod mount fan, make sure the ridge on mounting bracket engages the notch in the

downrod ball.

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and

junction box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a

point on the ceiling above the tip of one of the blades. Measure this distance from blade tip to ceilng.

Keeping measure within 1/8", rotate the fan until the next blade is positioned for measurement. e-

peat for each blade. If all blade levels are not equal, you can adjust blade levels by the following pro-

cedure. To adjust a blade tip down, insert a washer (not supplied) between the blade and blade holder

at the screw closest to the motor. To adjust a blade tip up, insert washer (not supplied) between the

blade and blade holder at the two screws farthest from the motor. everse the position of the washer

if blades mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute

the weight and possibly result in smoother operation.

1.Check blue wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

WA NING: Over lamping the fan will result in the fan lights shutting down until the

proper wattage of bulbs are installed. eset the lights by turning off the wall switch,

breaker,or by remote. eplace bulbs with the correct wattage bulbs, turn the power on.

CAUTION: Make sure main power is turned off before entering switch housing and/ or

canopy.

WA NING: Before attempting to replace the fuse make sure the main power is turned off to

the fan. eplace only with a 3 amp fuse. (Fuse is inside the canopy on the blue wire to re-

mote receiver, push and twist the cap to open the fuse case).

2. If fan sounds noisy:

1. If fan does not start:

3. If fan wobbles:

4. If light does not work:

TOUBLE SHOOTING

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In

some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trou-

ble Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation, please call our

Customer Service Center at the

number printed on your parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means can-

not be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

Trouble Suggested emedy

Apr.2012 New format

Jun.2013 Update for CUL regulation

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 5HV52 F Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HVO44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Haven 5HVO52BKD Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company AC-552 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ASR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5STR52 Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5VL52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MHR52RBD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 4SBWR56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Jovie 3JVR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5BY52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Diamond 4DDR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5hM52XX series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3SU54BK Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MUR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5EM68 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5NCR56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5EPR60BRD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DCR60XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5GIR54XXD-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4ICR52XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5YK60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AMR60BSD Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung