Monte Carlo Fan Company 5MHR52RBD-L Series Bedienungsanleitung

Owner’s

Manual

Ceiling Fan Installation Instructions

For 5MHR52RBD-L Series Fans

READ AND SAVE THESE INSTRUCTIONS

Total fan weight

with lights

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-

1999), including fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on

one side of the outlet box and ungrounded conductor on the other side of the outlet box.

Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being

switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from

the floor to the trailing edge of the blade.

To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support.

(Mounting must support at least 35 lbs.)

Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

NEVER place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equip-

ment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American

Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched

on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the

service panel.

10.

11.

12.

13.

14.

15.

Installation

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

SAFETY TIPS

TOOLS REQUIRED

Phillips Screwdriver Wire Cutters Pliers Step Ladder

Before you begin installing the fan, Switch power off

at Service panel and lock service disconnecting means

to prevent power from being switched on accidentally.

When the service disconnecting means cannot be

locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

Before installing this fan make sure the outlet

box is properly installed to the house structure.

To reduce the risk of fire, electric shock, or per-

sonal injury, mount to outlet box or supporting

system acceptable for fan support.

(Mounting must support at least 35 lbs.)

Use metal outlet box suitable for fan support

(must support 35 lbs). Before attaching fan to

outlet box, ensure the outlet box is securely

fastened by at least two points to a structural

ceiling member ( a loose box will cause the fan

to wobble). Use only the screws pro-

vided with the outlet box.

For downrod instal-

lation refer to step

For flush mount

installation refer to

step 27.

Loosen lock nuts and screws on yoke

till you can not feel screw on inside

of yoke.

Remove keeper from cross pin and

then cross pin from yoke. Replace

keeper on cross pin and save.

Install downrod into yoke. Align hole

in downrod with hole in yoke and

install cross pin. Install keeper into

cross pin.

Place canopy and then yoke cover on

downrod. Thread leadwires and safe-

ty cable through downrod as shown.

Tighten 2 downrod set screws and

lock nuts.

Raise fan with downrod assembled to

the ceiling bracket and hang fan

assembly. Be sure to rotate the

downrod ball so that the notch in the

bracket engages the slot in the ball.

Set dip switches on the Remote Transmitter and Remote

Receiver to the same settings. This must be done so the

units will communcate properly. If you have other fans you

can set to control from one transmitter by setting both

receivers the same as the transmitter. If you have more

than one fan with remote. You can set the dip switches to

different positiosns to have seperate control.

Remote Transmitter Dip swtiches

Remote Receiver Dip switches

Fan and light kit combinations over 35 lbs,

in both flush and downrod mode the safety

cable must be installed into the house struc-

ture beams using the 3” lag screws,washers,

and lock washers. provided. Make sure that

when the safety cable is fully extended the

lead wires are longer than the cable and no

stress is placed on the lead wires.

10 Safety cable installation

Safety Cable

Lag Screw

safety

cable

3” lag

screw lock

washer

Install remote receiver by sliding into opening in

the Mounting bracket. Make sure that the dip

switches on the Transmitter and the Receiver

are set to the same position. See Fig 38 for

remote operation

Make wiring connections as indicated above.

White from fan to white from remote marked

N. Blue from fan to blue from remote marked

light. Black from fan to Black from remote

marked L. White from house to white from

remote marked AC N . Black from house to

Black from remote marked AC L. Connect all

green ground wires to Ground wire from

House.

white

black

Lift Canopy to ceiling aligning the

key hole slots with the screws on the

bottom of the Mounting bracket.

Rotate the canopy Counter Clockwise

to lock in place. Tighten the screws

to secure the Canopy. See inset for

Keyhole shape

Attach blades to motor using screws

and washers in hardware bag and

tighten screws securely.

Loosen 3 screws and remove 1 screw

from motor plate. Save removed

screw for use later.

Install light plate to fan by twisting

plate with key hole slots into place.

Replace screw removed and tighten

the 4 screws securely.

Plug white wire from fan to white

wire from light kit. Then plug black

wire from fan to black wire from light

kit.

Remove 1 screw and loosen other 3.

Twist and remove plate.Then remove

body of fan.

To install fan witout light kit ,attach

switch cap into grooves and twist to

lock into place.

Loosen 2 screws and remove 1 screw

from motor plate. Save removed

screw for use later.

Install light plate to fan by twisting

plate with key hole slots into place.

Replace screw removed and tighten

the 3 screws securely.

Install glass with finial cap and tight-

en in direction of arrow.

Install 3 x 40 watt incandescent candelabra

bulbs. Bulbs included. WARNING: Over

lamping the fan will result in the fan

lights shutting down until the proper

wattage of bulbs are installed.

Reset the lights by turning off the wall

switch, breaker,or by remote. Replace

bulbs with the correct wattage bulbs, turn

the power on.

Align seams as shown above.

(Blades not shown

Align the arrow from light kit cover-

with the light pan. All 3 arrows

should be aligned.

Align seams

If installing light kit skip step

20 & 21

Remove lock nuts and screws on

yoke.

Remove keeper from cross pin and

then cross pin from yoke.

29 30

Remove 8 screws from the flywheel.

Save for later. Remove the flywheel.

27 Flush mount installation

Insert house wires through center

hole.Install the mounting plate to the

outlet box.Use only the screws pro-

vided with the outlet box.

Hang motor from hook on the

mounting plate. Use the closed

hole.Place receiver in the hanging

plate.

Separate from bracket.

Remove screws with wrench.

Make wiring connections as indicated above.

White from fan to white from remote marked

N. Blue from fan to blue from remote marked

light. Black from fan to Black from remote

marked L. White from house to white from

remote marked AC N . Black from house to

Black from remote marked AC L. Connect all

green ground wires to Ground wire from

House.

white

black

Set dip switches on the Remote Transmitter and Remote

Receiver to the same settings. This must be done so the

units will communcate properly. If you have other fans you

can set to control from one transmitter by setting both

receivers the same as the transmitter. If you have more

than one fan with remote. You can set the dip switches to

different positiosns to have seperate control.

Remote Transmitter Dip swtiches

Remote Receiver Dip switches

Place receiver into the lower hang-

ing plate.

Remove the yoke from the motor by

removing 6 screws.

Remove the yoke from the mounting

plate.

Stick the plastic plate onto the hang-

ing bracket aligning the holes as

shown above.

Thread safety cable through center

hole of the mounting plate. Thread

your house wires through center hole

also.These will be needed for wiring

of the fan.

For Canadian installation and for USA fan and

light kit combinations over 35 lbs, in both flush

and downrod mode the safety cable must be

installed into the house structure beams using

the 3” lag screws provided. Make sure that

when the safety cable is fully extended the

leadwires are longer than the cable and no

stress is placed on the leadwires.

37 Safety cable installation

Safety Cable

Lag Screw

Safety Cable

Washer

Lock Washer

Place face plate over battery compartment and

buttons. Place remote over 2 pins on front

cover. Attach cover of remote by placing over 4

pins and snaping into place.

Install wall control unit to outlet box

using machine screws provided.

Attach front cover to wall control

with screws provided. Snap battery

cover in place.

48 HAND HELD INSTALL

WALL MOUNT INSTALL

Remove cover by snaping off from top or bot-

tom. Remove battery cover. Install 12V battery

into wall remote. Duracell MN21 / Eveready A23

/ GP 23A all 12V.Attach cover of remote by plac-

ing over buttons and snap the battery cover in

place.

46Refer back to

step 22 for

blade and light

kit installation.

Tighten all screws.

Install by placing over screws and

twisting.Reinstall screw taken out

from step 28.

Lift motor aligning studs mounting

plate with holes on motor bracket.

Re-install nuts and tighten.

FAN SPEED Depress “l dot” for low speed, “2 dots” for medium or “3 dots” for

high. To turn fan off press square”.

LIGHT DIMMER To turn light on, press light dimmer once quickly. To turn off

press once quickly while light is on. To dim light hold down button “light dimmer”.

The light will cycle from bright to dim to bright until button is released. Light will

maintain last setting if turned off.

FORWARD/REVERSE Depress rev button allow a few seconds for remote to

change rotation direction with fan running.

HIGH SPEED

MEDIUM SPEED

LOW SPEED

FAN OFF SETTING

(Turns fan off only)

FAN REVERSE

(Press once to

change direction of

the fan)Fanmust be

running to reverse.

LIGHT ON/OFF SET-

TING AND DIMMER

(Press and hold to

dim light infinitively)

LED LIGHT

Remote Control Transmitter Features:

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

3.Make sure forward/reverse switch is firmly in up or down position. Fan will not operate when

switch is in the middle.

CAUTION: Make sure main power is turned off.

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each other or

against the interior wall of the switch housing.

CAUTION: Make sure main power is turned off before entering switch housing.

4.Some fan motors are sensitive to signals from Solid State variable speed controls. DO NOT USE

a Solid State variable speed control.

5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear after

this period.

1.Make sure that the ridge of the canopy engages the notch in the downrod ball.

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and

junction box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting

a point on the ceiling above the tip of one of the blades. Measure this distance from blade tip to

ceilng. Keeping measure within 1/8", rotate the fan until the next blade is positioned for measure-

ment. Repeat for each blade. If all blade levels are not equal, you can adjust blade levels by the fol-

lowing procedure. To adjust a blade tip down, insert a washer (not supplied) between the blade and

blade holder at the screw closest to the motor. To adjust a blade tip up, insert washer (not supplied)

between the blade and blade holder at the two screws farthest from the motor. Reverse the posi-

tion of the washer if blades mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistrib-

ute the weight and possibly result in smoother operation.

1.Check blue wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

WARNING: Over lamping the fan will result in the fan lights shutting down

until the proper wattage of bulbs are installed.

Reset the lights by turning off the wall switch, breaker,or by remote. Replace bulbs

with the correct wattage bulbs, turn the power on.

CAUTION: Make sure main power is turned off before entering switch housing or canopy.

2. If fan sounds noisy:

1. If fan does not start:

3. If fan wobbles:

4. If light does not work:

TROUBLE SHOOTING

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In

some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble

Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation, please call our

Customer Service Center at the

number printed on your parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot

be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Customer Service Center:

301 West Washington St.

Riverside, NJ 08075

1-800-519-4092

www.montecarlofans.com

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 3AVLR54 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ELR44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5vsr44XXd-l series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5AYR54 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3KNR52XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TF24BS Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5SI Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3IKR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5GIR54XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Cupra 3CPR60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ROZR44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4MC20XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 25003 Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5AGR56 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3VNR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52XXD-L Series Fan Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MAVR88XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Arcade 3ARR68 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5EM68 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MAVR60XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5EPR60BRD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CY60XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company AC-552 Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung