Monte Carlo Fan Company 5FWR52XXD Series Bedienungsanleitung

Ceiling Fan Installation Instructions

For 5FWR52XXD Series Fans

READ AND SAVE THESE INSTRUCTIONS

Total fan weight

OWNER’S

MANUAL

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes ANSI/NFPA 70-1999),

including fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding con-

ductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.

Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from

being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7

feet from the floor to the trailing edge of the blade.

To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support and

use only the screws provided with the outlet box. (Mounting must support at least 35 lbs.)

Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating

blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heat-

ing equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being

switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such

as a tag, to the service panel.

Airflowdirection: warm weather-switch to left - forward / cool weather -switch to right - reverse

10.

11.

12.

13.

14.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

SAFETY TIPS

TOOLS REQUIRED

Phillips Screwdriver Wire Cutters Pliers Step Ladder

Before you begin installing the fan, Switch

power off at Service panel and lock service dis-

connecting means to prevent power from being

switched on accidentally. When the service dis-

connecting means cannot be locked, securely

fasten a prominent warning device, such as a

tag, to the service panel.

Before installing this fan make sure the outlet box is

properly installed to the house structure. To reduce

the risk of fire, electric shock, or personal injury,

mount to outlet box or supporting system acceptable

for fan support. (Mounting must support at least 35

lbs.)

Loosen the 2 set screws in yoke for

downrod to slip into yoke.

Installation

Use metal outlet box suitable for fan support

and use only the screws provided with the out-

let box (must support 35 lbs). Before attaching

fan to outlet box, ensure the outlet box is

securely fastened by at least two points to a

structural ceiling member ( a loose box will

cause the fan to wobble). Use only the

screws provided with the outlet box.

Place canopy on downrod. (as

shown)

Thread leadwires and safety cable

through downrod. (as shown)

Insert downrod into yoke on top of

the Fan Body. Align the hole in the

Downrod with the hole in the Yoke.

Insert the Pin through the Yoke and

Downrod until the point appears on

the other side.

Install the Keeper Pin

Remove and keep the 4 screws and

fiber washers pre-attached. Install

the upper glass with screws and fiber

washers securely.

Place blade holders onto blades align-

ing holes in blade holder with holes in

blade. Make sure the side of the

blade you select is facing downward.

Install 3 screws and washers to back

side of blade as shown. Tighten

screws securely.Repeat this process 4

more times.

Install 4 x 15 watt candelabra

base bulbs included.

Remove 2 cardboards pre-installed

to the fan body. Rotate the center

flywheel so that the hole in flywheel

is facing opening of the upper light

kit plate. Insert the blade/blade arm

assembly into the flywheel hole and

tighten the screws securely. Repeat

4 more times.

Tighten the 2 set screws on yoke

once the downrod is installed in

place.

For Canadian installation in both flush and downrod

mode the safety cable must be installed into the

house structure beams using the 3” lag screws pro-

vided. Make sure that when the safety cable is

fully extended the leadwires are longer than the

cable and no stress is placed on the leadwires.

Safety Cable

Lag Screw

Washer

Lock Washer

Safety Cable

Set dip switches on the Remote Tr

ansmitter and Remote

eceiver to the same settings. This must be done so the

units will communcate properly. If you have other fans you

can set to control from one transmitter by setting both

receivers the same as the transmitter

. If you have more than

one fan with remote. You can set the dip switches to different

positiosns to have seperate control.

Remote Transmitter Dip swtiches

Remote Receiver Dip switches

Ready for wiring

Install remote receiver into mounting

bracket.

Safety cable installation

Hang assembled fan from the mounting bracket

installed to ceiling in previous step. Make sure the

fan is hanging straight. Rotate fan until the tab on

the Mounting bracket engages the slot on the

Downrod Ball. This must be done to prevent the fan

body from rotating when the blades are in motion.

Place glass on fitter

, install rubber

washer and hex nut to glass and

then tighten the finial nut securely

by hand.

Place the light fitter and tighten with

screws and washers.

Install 3 x 40 watt candelabra base

bulbs. Bulbs not included.

Remove the finial nut and hex-

nut from fitter.

Remove three screws and wash-

ers from light fitter.

Connect white wire from fan to white

wire from light fixture. Then plug

blue wire from fan to black wire from

light fixture.

Lift canopy allowing the 2 studs

to protrude through the canopy

and install knurled nuts as shown.

Tighten the knurled nuts securely.

Place face plate over battery compartment and

buttons. Place remote over 2 pins on front

cover

. Attach cover of remote by placing over 4

pins and snapping into place.

30 HAND HELD INSTALL

white

black

Make wiring connections as indicated above.

White from fan to white from remote marked

N. Orange from fan to Orange from remote

marked Light/up. Blue from fan to blue from

remote marked down light. Black from fan to

Black from remote marked L. White from

house to white from remote marked AC N .

Black from house to Black from remote

marked AC L. Connect all green ground wires

to Ground wire from House.

orange

blue

Green

white

black

House

Fan

fuses

Make wire connections to power source using wire

nuts provided. Make sure that no filiments are out-

side of the wirenut. After making the wire connec-

tions, the wires should be spread apart with the

grounded conductor and the equipment-grounding

conductor on one side of the outlet box and

ungrounded conductor on the other side of the outlet

box. The splices after being made should be turned

upward and pushed carefully up into the outlet box.

Reverse function for this fan is a

switch on the top housing of the fan

body. Turn fan off and wait for fan to

stop then flip the switch to reverse

the direction of the blades.

Remove cover by snaping off from top or bot-

tom. Remove battery cover. Install 12V battery

into wall remote. Duracell MN21 / Eveready A23

/ GP 23A all 12V

.Attach cover of remote by

placing over buttons and snap the battery cover

in place.

Install wall control unit to outlet box

using machine screws provided.

31 WALL MOUNT INSTALL

Attach front cover to wall control

with screws provided. Snap battery

cover in place.

Remote Control Transmitter Features:

FAN SPEED Depress “l dot” for low speed, “2 dots” for medium or “3 dots” for

high. To turn fan off press square”.

LIGHT DIMMER To turn light on, press light dimmer once quickly. To turn off

press once quickly while light is on. To dim light hold down button “light dimmer”.

The light will cycle from bright to dim to bright until button is released. Light will

maintain last setting if turned off.

HIGH SPEED

MEDIUM SPEED

LOW SPEED

FAN OFF SETTING

(Turns fan off only)

DOWNLIGHT ON/OFF

SETTING AND DIMMER

(Press and hold to dim

light infinitively)

LED LIGHT

UPLIGHT ON/OFF SET-

TING AND DIMMER

(Press and hold to dim

light infinitively)

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

CAUTION: Make sure main power is turned off.

3.Make sure forward/reverse switch is firmly in up or down position. Fan will not operate when

switch is in the middle.

4.Make sure that shipping stabilizer tabs have been removed from motor.

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each other or

against the interior wall of the switch housing.

CAUTION: Make sure main power is turned off before entering switch housing and/or

canopy.

4.If using an optional Ceiling Fan Light Kit, check to be sure the screws securing the glassware are

finger tight. Check to be sure light bulb is tight in socket and not touching glass shade(s). If vibra-

tion persists from glass, remove glass and install a 1/4" wide rubber band on glass neck to act as

an insulator. Replace glass and tighten screws against rubber band.

5.Some fan motors are sensitive to signals from Solid State variable speed controls.

DO NOT USE a Solid State variable speed control.

6.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear after

this period.

1.Make sure that the ridge of the canopy engages the notch in the downrod ball. (See illustration

in Step #14 of Downrod Mount installation).

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and

junction box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by select-

ing a point on the ceiling above the tip of one of the blades. Measure this distance from blade tip to

ceilng. Keeping measure within 1/8", rotate the fan until the next blade is positioned for measure-

ment. Repeat for each blade. If all blade levels are not equal, you can adjust blade levels by the

following procedure. To adjust a blade tip down, insert a washer (not supplied) between the blade

and blade holder at the screw closest to the motor. To adjust a blade tip up, insert washer (not

supplied) between the blade and blade holder at the two screws farthest from the motor. Reverse

the position of the washer if blades mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistrib-

ute the weight and possibly result in smoother operation.

1.Check blue wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

CAUTION: Make sure main power is turned off before entering switch housing and/ or

canopy.

WARNING: Before attempting to replace the fuse make sure the main power is turned off

to the fan. Replace only with a 3 amp fuse. (Fuse is inside the canopy on the blue and

orange wires to remote receive, push and twist the cap to open the fuse case).

2. If fan sounds noisy:

1. If fan does not start:

3. If fan wobbles:

4. If light does not work:

TROUBLE SHOOTING

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In

some cases, these installation errors may be mistaken for defects. If you experience any faults, please check

thisTroubleShooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation, please call

our Customer Service Center at the

number printed on your parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot

be locked, securely fasten aprominent warning device, such as a tag, to the service panel.

Customer Service Center:

301 West Washington St.

Riverside, NJ 08075

1-800-519-4092

www.montecarlofans.com

Trouble Suggested Remedy

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 5MMR54 D-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5PPR54 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Linden 3LD48 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5VYR56XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CXR52 Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 4SBWR56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HV52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MS52RB Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5vsr44XXd-l series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ED56WAD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DVR60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CY60XX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ASPR56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5OBR52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3JVR44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company AC-552 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Edge Coastal 60 Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3IKDR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3DIR52XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Arcade 3ARR68 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5BUR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5SLR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HS52XXD-L Series Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung