Monte Carlo Fan Company 5TLR54 Series Gebrauchsanweisung

Owner’s Guide and Installation Manual

Total fan weight

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

Attach sales receipt to this card and retain as yourproof of purchase

To register your fixture, please visit our website www.montecarlofans.com

5TLR54XX Series Fan

UL Model NO. : 5TLR54XX

9.0 kgs

19.8 lbs

Cautions and Warnings

Installation work and electrical wiring must be done by qualied person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-1999),

including re-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side

of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be turned upward and pushed

carefully up into the outlet box.

WARNING:Before you begin installing the fan, servicing or cleaning unit, Switch power o at Service panel and lock service disconnecting means to

prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the oor to

the trailing edge of the blade.

WARNING:To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of 15.9 kg (35 lbs) or

less”And Use Mounting Screws Provided With The Outlet Box.

CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Remove Knockouts In

The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to the building structure (or the ceiling

joist).

WARNING:To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert

foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING:To reduce the risk of re or electric shock, this fan must be installed with an isolating wall control/switch.

WARNING:To reduce the risk of re or electric shock, this fan should only be used with fan speed control part no. UC7067RY manufactured by Rhine

Electronic Co., Ltd.

WARNING:To reduce the risk of re or electric shock, do not use this fan with any other solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airow needed for safe operation of fuel-burning equipment may be aected by this unit’s operation. Follow the heating equipment

manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for

Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION:To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

CAUTION:The light source is designed for this specic application and can overheat if serviced by untrained personnel. If any servicing is required, the

product should be returned to an authorized service facility for examination or repair.

All set screws must be checked and tightened where necessary before installation.

Note: Suitable for use in damp locations.

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers

WARNING:TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

1 2 3

4 5 6

OFF

Before you begin installing the fan, Switch

power o at Service panel and lock

service disconnecting means to prevent

power from being switched on

accidentally. When the service

disconnecting means cannot be locked,

securely fasten a warning device, such as

a tag, to the service panel.

Use AC 120V/60HZ power supply only.

Before installing this fan make sure the

outlet box is properly installed to the

house structure. To reduce the risk of re,

electric shock, or personal injury, mount

to outlet box or supporting system

acceptable for fan support.

(Mounting must support at least 35 lbs.)

Use metal outlet box suitable for fan

support and use only the screws provided

with the outlet box (must support 35 lbs).

Before attaching fan to outlet box, ensure

the outlet box is securely fastened by at

least two points to a structural ceiling

member ( a loose box will cause the fan to

wobble). Remove the two outlet box

screws provided with the box, aligning

the holes of the mounting bracket with

the holes of the outlet box. Reinstall the 2

outlet box screws securely.

Partially loosen downrod set screws from

yoke at top of motor assembly.

Remove preassembled cross pin and

keeper pin from downrod.

Place downrod over canopy, canopy

bottom ring and yoke cover. Thread lead

wires and safety cable from motor

assembly through downrod.

Slip downrod into motor housing yoke,

aligning holes and install cross pin and

keeper pin.

Insert cross pin through yoke and downrod

until point appears on the other side, and

insert keeper pin on cross pin.

Pull the downrod up tight against the

cross pin, and then evenly tighten the

downrod set screws on motor housing

yoke.

Place yoke cover on top housing of fan.

Warning: Cross pin and keeper pin must be

installed securely, failure to install them will

result in serious injury.

Yoke cover

Mounting bracket

Downrod

Cross pin

Keeper pin

Canopy

Downrod

Canopy bottom ring

Downrod Mount Installation

7 8 9

10 11

Install ball end of downrod into mounting

bracket opening. Align (engage) slot on

ball with tab on mounting bracket.

Warning:Failure to align slot on ball with

tab may result in serious injury.

Important: If using the angle mount,

make sure open end of mounting bracket

is installed facing the higher point of the

ceiling and make sure the ceiling angle is

not steeper

than 30º.

For Canadian installation and for USA fan

and light kit combinations over 35 lbs, in

both ush and downrod modes the safety

cable must be installed into the house

structure beams using 3” lag screws,

washers and lock washers provided. Make

sure that when the safety cable is fully

extended the lead wires are longer than

the cable and no stress is placed on the

lead wires.

Note: If Installing The Secondary Support

Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box.

Set dip switches on the Remote

Transmitter and Remote Receiver to the

same settings. This must be done so the

units will communicate properly. If you

have other fans you can set to control

from one Transmitter by setting receivers

the same as the Transmitter. If you have

more than one fan with remote, you can

set the dip switches to dierent positions

to have separate control.

Make wiring connections using wire

connectors provided as indicated above.

White from fan to White from remote

marked N. Black from fan to Black from

remote marked L. Blue from fan to Blue

from remote marked FOR LIGHT. White

from house to White from remote marked

AC N. Black from house to Black from

remote marked AC L. Connect all green

grounded wires to Grounded wire from

House. Make sure that no laments are

outside of the wire connectors.

Insert the remote receiver into mounting

bracket.

Lift Canopy allowing the 2 studs to

protrude through the canopy.

Next lift the cover ring and install knurled

nuts as shown. Tighten the knurled nuts

securely. The canopy should adjust for any

irregularity in the ceiling or Outlet box.

Make sure the studs protruding from the

bottom of the Mounting bracket are

installed with threads all the way through

the bracket.

SAFETY CABLE INSTALLATION

Dip switches

Lag screw

Safety cable

Washer

Lock washer

Stud

Tab

Slot

Wall

switch

White

Blue

Black

Receiver

Ground/Green

Black

(Live)

White

(Natural)

Power

source

Go to step 21 to nish

installation

12 13 14

15 16 17

Remove every other screws from yoke

located on top of fan assembly. Keep

screws.

Note: Flush mount is not available with

vaulted ceiling.

Place canopy and rubber pad over lead

wire and safety cable and align the larger

holes in canopy and holes on rubber pad

with the set screws on yoke.

Reinstall the 3 set screws remove in step

12. Tighten screws securely.

To prepare the fan for wiring, hang fan

onto mounting bracket by sliding the

canopy over the mounting bracket hook

(Use one of non-slotted holes on the

rim of the canopy).

For Canadian installation and for USA fan

and light kit combinations over 35 lbs, in

both ush and downrod modes the safety

cable must be installed into the house

structure beams using 1.5” lag screws,

washers and lock washers provided. Make

sure that when the safety cable is fully

extended the lead wires are longer than

the cable and no stress is placed on the

lead wires.

Note: If Installing The Secondary Support

Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box.

Remove side covers from canopy

exposing 4 holes. 2 closed holes and 2

open “L” shape holes.

Flush Mount Installation

Side cover

Rubber pad

SAFETY CABLE INSTALLATION

Lag screw

Safety cable

Washer

Lock washer

Hook

18 19

21 22 23

Set dip switches on the Remote

Transmitter and Remote Receiver to the

same settings. This must be done so the

units will communicate properly. If you

have other fans you can set to control

from one Transmitter by setting receivers

the same as the Transmitter. If you have

more than one fan with remote, you can

set the dip switches to dierent positions

to have separate control.

Make wiring connections using wire

connectors provided as indicated above.

White from fan to White from remote

marked N. Black from fan to Black from

remote marked L. Blue from fan to Blue

from remote marked FOR LIGHT. White

from house to White from remote marked

AC N. Black from house to Black from

remote marked AC L. Connect all green

grounded wires to Grounded wire from

House. Make sure that no laments are

outside of the wire connectors.

Insert the remote receiver into mounting

bracket.

Install 2 of the screws to the side panel

corresponding to the open slotted holes

on the canopy upper rim, screws provid-

ed. Remove the all thread studs from the

lower part of the mounting bracket.

Lift fan to mounting bracket, aligning the

“L”shape holes with the screws on the

mounting bracket. Turn the fan clockwise

to lock in position. Install the other 2

canopy mounting set screws from the

hardware pack and tighten all screws

securely.

Install blade bracket with blade by 3 blade

screws and washers provided. Tighten

screws securely. Repeat this process for

remaining blades.

Note: Make sure the side with a label “This

side up” is installed upward.

Remove shipping stabilizers from motor

assembly.

Install the blade assembly to motor using

the preinstalled screws. Tighten screws

securely. Repeat this process for

remaining blade assemblies.

Remove the 3 set screws on top plate of

light xture, keep screws.

Receiver

Dip switches

Blade bracket

Blade

Shipping

stabilizers

Top plate

Wall

switch

Black

(Live)

Ground/Green

Whit

(Neutral)

White

Blue

Black

This side up

24 25

27 28 29

Connect the plug from fan with the plug

from switch housing. Be sure plugs

connection clasped together completely.

Attach switch housing onto top plate,

aligning the holes and reinstall the 3 set

screws removed in step 23 and tighten all

screws securely.

HAND HELD INSTALL

Place battery cover over battery

compartment and buttons. Place remote

over 2 pins on front cover. Attach cover of

remote by placing over 4 pins and

snapping into place.

Install wall control unit to outlet box using

machine screws provided.

Attach front cover to wall control unit

with screws provided. Snap battery cover

in place

Remove battery cover. Install 12V battery

into wall remote. Duracell MN21 /

Evereday A23 / GP 23A all 12V. Attach

cover of remote by placing over buttons

and snap the battery cover in place.

Battery cover

Battery

WALL MOUNT INSTALL

Switch housing

FAN SPEED: Depress“1 dot” for low speed, “2 dots” for medium or “3 dots” for high. To turn fan o press square”.

LIGHT DIMMER: To turn light on, press light dimmer once quickly. To turn o press once quickly while light is on. To dim light hold

down button“light dimmer”. The light will cycle from bright to dim to bright until button is released. Light will maintain last setting if

turned o.

FORWARD/REVERSE: Depress reverse button with fan running. Allow a few seconds for fan to slow down and change rotation

direction. Clicking noise may be heard after depressing button.

Note: If not using for long periods of time, remove battery to prevent damage to remote transmitter, and store the remote

transmitter away from excess heat or humidity

Remote Control Transmitter Features

MEDIUM SPEED

HIGH SPEED

LED LIGHT

LOW SPEED

FAN OFF SETTING

(Turn fan o only)

FAN REVERSE (Press once

to change direction of

the fan) Fan must be

running to reverse.

LIGHT ON/OFF SETTING

AND DIMMER (Press and

hold to dim light infinitely)

Trouble Shooting

or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,

installation, please call our Customer Service Center at the

number printed on your parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be

locked, securely fasten a prominent warning device, such as a tag, to the service panel.

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

CAUTION: Make sure main power is turned off.

either way. Fan will not operate when switch is in the middle.

4.If this fan uses remote controller, make sure dip switches are setting properly and make

sure battery is effective.

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

CAUTION: Make sure main power is turned off before entering switch housing.

4.Check to be sure light bulb is tight in socket and not touching the glass shade.

5.Some fan motors are sensitive to signals from Solid State variable speed controls.

6.Allow "break-in" periodof 24 hours. Mostnoises associated with a new fan will disappear

after this period.

1.If this is a downrod mount fan, make sure the ridge on mounting bracket engages the

notch in the downrod ball.

2.Make sure that canopy, mounting bracket or mounting plate are tightened securely to

4.Check that all blade holders are tightened securely to motor.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the blades. Measure this distance

from blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade

is positioned for measurement. Repeat for each blade. If all blade levels are not equal,

you can adjust blade levels by the following procedure. To adjust a blade tip down, insert

a washer (not supplied) between the blade and blade holder at the screw closest to the

motor. To adjust a blade tip up, insert washer (not supplied) between the blade and blade

holder at the two screws farthest from the motor. Reverse the position of the washer if

blades mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can

redistribute the weight and possibly result in smoother operation.

1.Check blue wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulb and make sure bulb is tight in socket.

5.Remove light kit and check the plug connections if they are present.

6.If this fan uses remote controller, make sure dip switches are setting properly and make

sure battery is effective.

CAUTION: Make sure main power is turned off before entering switch housing and/or

canopy.

2. If fan sounds noisy:

3. If fan wobbles:

4. If light does not work:

1. If fan does not start:

Trouble Suggested Remedy

Mar.2015

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 5RDR Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company AC-552 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HS42RB Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Mach One Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5PR52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Titus Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AVOR56 D-V1 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WS52XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HS42XX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CXR52 Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 4MC20 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HS52 D-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company AC-552 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Haven 5HVO52BKD Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3RULSM52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4AAR13XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CNR52 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5AB52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Hicks 3HCKR60 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3IKR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5EM60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5PE56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ALMSM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5FNR60 Series Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung