Monte Carlo Fan Company 5WA52 Series Bedienungsanleitung

Quality Ceiling fans

Owner’s

Manual

Ceiling Fan Installation Instructions

For 5WA52 Series Fans

READ AND SAVE THESE INSTRUCTIONS

Total fan weight

Install mounting brackets to outlet

box in ceiling using the screws and

washers provided with the outlet

box.

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-

1999), including fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on

one side of the outlet box and ungrounded conductor on the other side of the outlet box.

Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being

switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from

the floor to the trailing edge of the blade.

To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support.

(Mounting must support at least 35 lbs.)

Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

NEVER place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equip-

ment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American

Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched

on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the

service panel.

10.

11.

12.

13.

14.

15.

Installation

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

SAFETY TIPS

TOOLS REQUIRED

Phillips Screwdriver Wire Cutters Pliers Step Ladder

Before you begin installing the fan, Switch power off

at Service panel and lock service disconnecting means

to prevent power from being switched on accidentally.

When the service disconnecting means cannot be

locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

Feed motor lead wires through downrod/canopy

assembly and insert downrod into motor yoke.

Next, insert clevis pin through yoke and down-

rod and secure with cotter pin. (see Inset)

Tighen both yoke set screws to further secure

downrod.

Carefully lift fan assembly onto mounting

bracket. Rotate fan so that the notch on

the ball engages the ridge in the mount-

ing bracket. This will allow hands-free

wiring.

Before installing this fan make sure the outlet

box is properly installed to the house structure.

To reduce the risk of fire, electric shock, or per-

sonal injury, mount to outlet box or supporting

system acceptable for fan support.

(Mounting must support at least 35 lbs.)

Unpack and inspect fan carefully to

be certain all contents are included.

(See exploded view parts lists.)

While the fan assembly is still on the

ground thread the safety cable

through the mounting bracket.

CANADIAN MOUNTING SYSTEM INSERT

Lift fan assembly and install the safety cable

directly to the building structure using the 3”

lag screw and plain washer provided. Before

proceeding to the the next step make sure that

the cable is properly installed and will support

the fan weight. Make sure the screw washer

and safety cable are installed using the order

pictured above.

Feed motor lead wires through downrod/canopy

assembly and insert downrod into motor yoke.

Next, insert clevis pin through yoke and down-

rod and secure with cotter pin. (see Inset)

Tighen both yoke set screws to further secure

downrod.

Mounting

Bracket

Safety Cable

Install mounting brackets to outlet box

in ceiling using the screws and wash-

ers provided with the outlet box.

CANADIAN SAFETY TIPS

WARNING: MOUNT ONLY TO AN OUTLET BOX

MARKED ACCEPTABLE FOR FAN SUPPORT

All set screws must be checked and retightened

where necessary before installation.

Carefully lift fan assembly onto mounting brack-

et. Rotate fan so that the notch on the ball

engages the ridge in the mounting bracket. This

will allow hands-free wiring. For wiring instruc-

tions please refer to page 4 step #7.

To gain access to the blade bracket

attachment holes remove the switch

housing cover by unscrewing the three

screws. Gently slide the cover off.

Combo-Blades feature two high quality finishes

on one blade. Select the one that best comple-

ments your decor, or change the style with just

a flip of the blade.

Attach blade brackets to blades using the blade

bracket screws and washers provided.

For pullchain controls, follow diagram above.

Make sure that all exposed wiring is secured

inside wire nuts. Note: Wires from house may

vary in color and may not include ground wire.

After wiring is conplete, gently push wires into

junction box with wire nuts pointing upward.

Refer to point 3 of safety tips.

7House Fan

Black

White

Green

Black

White

Green(Bracket)

Blue *

For control of fan and optional light from

wall location, follow diagram above.

NOTE: A professional electrician is recom-

mended for this type of installation.

Raise the canopy up and align the two holes in

the canopy with the two holes in the hanger

bracket. Secure with two 5/32 x 1/2” screws

provided.

Wiring option with wall speed control

Light Switch

Fan Switch

Wall

Control

Remove plastic shipping stabilizer tabs from

motor, if present. The screws, washers and

motor pads are pre-installed to the blade hold-

ers. Attach blade assembly to motor by tighten-

ing first screw one turn, then tighten second

screw securely. Then, go back and tighten first

screw securely.

After attaching blade; reinstall the switch

housing using the three screws previously

removed.

COMBO-BLADE

Standard wiring option

Green(Downrod)

*Attach blue wire

only if attaching

light kit with fan

Secure with

twist-lock wire

connectors

(included)

Shipping

stabilizer tab

Installation

After installation, please refer to operation, maintenance and troubleshooting

sections in this manual. If your fan is packaged with a light kit or

if you wish to install a separately purchased light kit, please refer

to the insert sheet titled: Light Kit Installation

Note:

Fiber

washers

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

3.Check to make sure the dip switches from the transmitter and receiver are set on the same

frequency.

4.Make sure forward/reverse switch is firmly in up or down position. Fan will not operate when

switch is in the middle.

5.Make sure that shipping stabilizer tabs have been removed from motor (see step # 13).

CAUTION: Make sure main power is turned off.

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each other

or against the interior wall of the switch housing.

4.If using an optional Ceiling Fan Kit, check to be sure the screws securing the glassware are

finger tight. Check to be sure light bulb is tight in socket and not touching glass shade(s). If

vibration persists from glass, remove glass and install a 1/4” wide rubber band on glass neck to

act as an insulator. Replace glass and tighen screws against rubber band.

CAUTION: Make sure main power is turned off before entering switch housing.

5.Some fan motors are sensitive to signals from Solid State variable speed controls

DO NOT USE a Solid State variable speed control.

6.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear

after this period.

1.Make sure that the ridge of the canopy engages the notch in the downrod ball.

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box

and junction box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the blades. Measure this distance from

blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade is posi-

tioned for measurement. Repeat for each blade. If all blade levels are not equal, you can adjust

blade levels by the following procedure. To adjust a blade tip down, insert a washer (not sup-

plied) between the blade and blade holder at the screw closest to the motor. To adjust a blade

tip up, insert washer (not supplied) between the blade and blade holder at the two screws far-

thest from the motor. Reverse the position of the washer if blades mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redis-

tribute the weight and possibly result in smoother operation.

1.Check wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

CAUTION: Make sure main power is turned off before entering switch housing.

2. If fan sounds noisy:

1. If fan does not start:

3. If fan wobbles:

4. If light does not work:

Trouble Shooting

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation,

or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,

please check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty

in installation, please call our Customer Service Center at the number printed on your parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service dis-

connecting means to prevent power from being switched on accidentally. When the service dis-

connecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

Touching

Ceiling

Figure1

Blade Tip Down:

BladeTipUp:

FanBlade

Figure2

Blade Brackets

Customer Service Center:

740 S.W. Loop 820, Suite 110

Fort Worth, Texas 76115

1-800-519-4092

SUGGESTED REMEDY

TROUBLE

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 5WS52XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5YM52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CSM60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4AAR13XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5GL52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AVLR54 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Hicks 3HCKR60 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MGMR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3DIR52RZWD-V1 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Colony Max Plus 5COM52 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company MC263 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company MC223 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MZR54 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CQM52XX-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Launceton 56 4LNCR56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company AC-572LF2000 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3VLR60ATIHAB Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Drawing Room 5ED56 D-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Haven 5HVO52BKD Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3VNR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TF24 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5STR52 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung