Monte Carlo Fan Company 3VLR60ATIHAB Gebrauchsanweisung

Total fan weight

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

Attach sales receipt to this card and retain as yourproof of purchase

To register your fixture, please visit our website www.montecarlofans.com

3VLR60XXX Series Fan

cETL Model NO. : 3VLR60XXX

8.7 kg

19.14 lbs

Owner’s Guide and Installation Manual

Cautions and Warnings

Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with applicable codes and standards (ANSI/NFPA 70), including

ﬁre-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side

of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be turned upward and pushed

carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to

prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the ﬂoor

to the trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of 15.9 kg (35 lbs)

or less” And Use Mounting Screws Provided With The Outlet Box.

CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Remove Knockouts

In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to the building structure (or the

ceiling joist).

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert

foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of ﬁre or electric shock, this fan should only be used with fan speed control part no. JY1028 manufactured by Satellite

Electronic ( Zhongshan ) Ltd

WARNING: To reduce the risk of ﬁre or electric shock, do not use this fan with any other solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airﬂow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment

manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for

Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

CAUTION: The light source is designed for this speciﬁc application and can overheat if serviced by untrained personnel. If any servicing is required, the

product should be returned to an authorized service facility for examination or repair.

All set screws must be checked and tightened where necessary before installation.

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

1 2 3

4 5 6

OFF

Before you begin installing the fan, Switch

power off at Service panel and lock

service disconnecting means to prevent

power from being switched on

accidentally. When the service

disconnecting means cannot be locked,

securely fasten a warning device, such

as a tag, to the service panel.

Use AC 120V/60HZ power supply

only.

Before installing this fan make sure the

outlet box is properly installed to the

house structure. To reduce the risk of

ﬁre, electric shock, or personal injury,

mount to outlet box or supporting system

acceptable for fan support.

(Mounting must support at least 35 lbs.)

Use metal outlet box suitable for fan

support and use only the screws provided

with the outlet box (must support 35

lbs). Before attaching fan to outlet box,

ensure the outlet box is securely fastened

by at least two points to a structural

ceiling member ( a loose box will cause

the fan to wobble). Remove the two outlet

box screws provided with the box,

aligning the holes of the mounting

bracket with the holes of the outlet box.

Reinstall the 2 outlet box screws

securely.

Partially loosen downrod set screw from

yoke at top of the motor assembly.

Remove hanger ball from downrod by

loosing the set screw and removing the

pin as shown in illustration. Keep parts.

Remove preassembled keeper pin and

cross pin from downrod.

Thread lead wires and safety cable from

motor assembly through downrod.

Install downrod. Thread downrod into the

yoke on top of fan until the holes on

downrod are aligned with the holes on the

yoke, and then install cross and keeper

pins. Tighten the downrod set screw.

Caution: To avoid damaging of lead wires

from downrod installation, make sure the

lead wires and safety cable are not twisted

when install the downrod.

Warning: Cross pin and keeper pin must

be installed securely, failure to install them

will result in serious injury.

Mounting bracket

Cross pin

Keeper pin

Downrod

Cross pin

Keeper pin

Hanger ball

Set screw

Yoke

7 8 9

10 11 12

Place canopy bottom cap and canopy

over lead wires, safety cable and

downrod, and then replace the hanger

ball.

Replace the hanger ball with pin and set

screw. Tighten it securely.

Warning: Make sure the pin is installed

well on hanger ball with downrod.

Install ball end of downrod into mounting

bracket opening. Align (engage) slot on

ball with tab on mounting bracket.

Warning: Failure to align slot on ball with

tab may result in serious injury.

Important: If using the angle mount,

make sure open end of mounting bracket

is installed facing the higher point of the

ceiling and make sure the ceiling angle is

not steeper than 20º. Longer downrod

may be necessary allowing the fan blades

to rotate without obstructions.

For Canadian installation and for USA fan

and light kit combinations over 35 lbs, in

both ﬂush and downrod modes the safety

cable must be installed into the house

structure beams using 3” lag screws,

washers and lock washers provided.

Make sure that when the safety cable is

fully extended the lead wires are longer

than the cable and no stress is placed on

the lead wires.

Note: If Installing The Secondary Support

Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box.

SAFETY CABLE INSTALLATION

Lag screw

Safety cable

Washer

Lock washer

Canopy bottom cap

Tab

Slot

Make wiring connections as indicates

above, using wire connectors provided.

Connect Black wire from fan to Black

(Live) wire from house. Connect White

wire from Fan to White (Neutral) wire from

house. Connect all green grounded wires

to Grounded wire from House. Make sure

that no ﬁlaments are outside of the wire

connectors.

After making the wire connections, the wires

should be spread apart with the grounded

conductor and the equipment-grounding

conductor on one side of the outlet box and

ungrounded conductor on the other side of

the outlet box. The splices after being made

should be turned upward and pushed carefully

up into the outlet box.

Lift Canopy allowing the 2 studs to

protrude through the canopy.

Next lift the canopy bottom cap and

install knurled nuts as shown. Tighten the

knurled nuts securely. The canopy should

adjust for any irregularity in the ceiling or

Outlet box.

Make sure the studs protruding from the

bottom of the Mounting bracket are

installed with threads all the way through

the bracket.

Power

supply

Wall switch

Black

White

Grounding/Green Grounded

wires Ungrounded

wires

Canopy

Stud

13 14 15

Install blade onto blade bracket with a top

plate by 3 blade screws and decorative

nuts provided. Tighten screws securely.

Repeat this process for remaining blades.

Fix the blade assembly with a

countersunk set screw using an Allen

wrench, screw and Allen wrench provided.

Tighten screw securely.

Note:To install blade assembly on the

shaft ﬁrmly, the set screw is made a little

interference ﬁt. It is a normal condition.

Important:Set screw must be fully

installed until it tightly jams against the

threads of the anchor bolt.

Install a decorative cap.

Slip the blade assembly on the shaft.

Install an anchor bolt counterclockwise

to ﬁx the blade assembly in position.

Tighten the bolt securely.

Blade bracket

Blade

Decorative nut

Blade assembly

Anchor bolt

Countersunk screw

Allen wrench

Shaft

Decorative cap

Top plate

Remote Controller Operation

Remove the battery cover from the remote control transmitter and install batteries.

Replace the cover. This remote uses 2 1.5V/AAA batteries.

Note: If not using for long period of time, remove battery to prevent damage to

remote transmitter, and store the remote transmitter away from excess heat or

humidity

Dimming, Non Dimming Setting (Only available for fans with light)

In the dimming mold, it is a light dimming selection and it is to be used with

dimmable luminaries. Press and hold the button to dim the light. The light will cycle

from bright to dim to bright until button is released. Light will maintain last setting if

turned off. Press and release the button quickly may turn light on/off. The remote

controller is set with dimming function at factory.

In ON/OFF (non-dimming mold), it is for light ON/OFF only (non-dimming function).

The remote control buttons control the fan speed as follows:

Fan speed

1 = minimum speed 2 = low speed 3 = medium low speed

4 = medium speed 5 = medium high speed 6 = high speed

This button turns the fan off.

Forward/Reverse button- This button is to control direction of fan rotation. Press once

to change direction of the fan rotation. Fan must be running to reverse.

Breeze-

Press the Breeze button, fan will operates at high speed (6th) for 30 seconds, then automatically

change to 5th, 4th, 3rd, 2nd, 1st at intervals of 30 seconds, and then change it from Low speed (1st) to

2nd, 3rd, 4th, 5th, 6th repeat the cycle until the breeze mold is cancelled.

Breeze mold can be erased by pressing the buttons of power or speed control.

Note

: This remote controller has auto resume function, the fan and light will maintain the last setting if

turned off with exception of the Breeze mold.

Battery cover

DIM (D)

ON/OFF (O)

SET

Universal Mode and Learning Mode

There are “Universal Mode” and “Learning Mode” (marks “0” and “1”) with the remote controller.

If choosing “Universal Mode”, simply place dip (code) switch at LOWER position (mark “0”). Your fan with the

remote controller is ready to use.

Note: If using universal mode, your fan can be controlled with other remote transmitters with the same setting.

To control the fan with speciﬁc remote transmitter, choose “Learning Mode” by placing the dip (code) switch

at UPPER (mark “1”) position and then make learn function setting as below.

Learn Function Setting

Important: Turn the power on for ONLY the speciﬁc fan you wish to pair with the remote controller. Make sure

to turn the power off for all other fans with which you use the same remote controller.

Restore power to your fan, press and hold the “SET” button to pair the Transmitter and receiver. You must

press the ‘SET” button within 60 seconds of restoring power to the fan.

Note:

Fan will operate at minimum speed after the setting.

Note

: If the power is on already, you must turn the power off then turn the power back for remote control

setting.

Note

: If reset the dip switch to “0” position (universal mold). It has to be paired again, run the learn function

setting.

Wall mount cradle

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO

CONDITIONS. (1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT

ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

The receiver provides the following protective functions:

Lock protection: The DC motor has a build-in safety feature

against blade obstruction during operation. If something

obstructs the fan blades, the motor will stop operation after

about 20 seconds of interruption. Please remove obstacles

and reset it by turning the power off, and then turn power

back on.

Over 40W protection: When the receiver detects motor

power consumption which is greater than 40W, the fan RPM

will automatically lower to prevent it from overloading.

User Tips

1. If your fan is operating automatically after installation, it is still using the factory setting. Follow the settings for Learn Mode

above to reset.

2. If the fan or light isn’t working, reset power (turn the power off then turn the power back on) and follow the Universal Mode or

Learn Mode remote control settings.

3. If two or more fans in the same remote signal range are on the same power supply, they cannot be operated separately by

remote control. Use a separate power supply for each fan, such as an individual wall switch, and restrict the power supply to

only the fan which you are pairing with its transmitter in order to use the remote controller.

4. When the fan is turned on to oscillate in either forward or reverse direction, it may shudder brieﬂy until fully engaged. This is a

normal operation for this fan; the shuddering will quickly cease as movement is engaged.

Install Transmitter wall mount cradle with 2 screws provided.

Useful tips:

The remote transmitter can be removed by pressing it

upward from the lower half.

The remote transmitter can be held on magnetic metal

materials by a magnet built in the transmitter.

Troubleshooting

or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,

installation, please call our Customer Service Center at the

number printed on your parts list insert sheet.

Warning

and lock the service panel to prevent the power from being switched back on accidentally. If the service panel

cannot be locked to prevent the power from being switched on accidentally, securely fasten a warning sign to the

service panel.

1. Check main and branch circuit fuses or circuit breakers.

2. Check line wire connections to fan and switch wire connections in switch housing.

CAUTION

either way. Fan will not operate when switch is in the middle.

4. If this fan uses a remote controller, make sure dip switches are in the correct setting

and make sure the battery works.

1. Check to make sure all screws in motor housing are snug (not over tightened).

2. Check to make sure the screws which attach the fan blade holder to the motor are tight.

3. Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

CAUTION

4. Check to be sure lightbulb is tight in socket and not touching the glass shade.

5. Some fan motors are sensitive to signals from Solid State variable speed controls.

6. Allow "break-in" period of 24 hours. Most noises associated with a new fan will

disappear after this period.

1. If this is a downrod mount fan, make sure the ridge on mounting bracket engages the

notch in the downrod ball.

2. Make sure that canopy, mounting bracket or mounting plate are tightened securely to

4. Check that all blade holders are tightened securely to motor.

5. Most fan wobble problems are caused when blade levels are unequal. Check this level

by selecting a point on the ceiling above the tip of one of the blades. Measure this distance

from blade tip to ceiling. Keeping measure within 1/8", rotate the fan until the next blade

is positioned for measurement. Repeat for each blade. If all blade levels are not equal,

you can adjust blade levels by the following procedure. To adjust a blade tip down, insert

a washer (not supplied) between the blade and blade holder at the screw closest to the

motor. To adjust a blade tip up, insert washer (not supplied) between the blade and blade

holder at the two screws farthest from the motor. Reverse the position of the washer if

blades mount from top of blade.

6. If blade wobble is still noticeable, interchanging two adjacent blades can redistribute the

weight and possibly result in smoother operation.

If the above steps do not eliminate the wobble problem, you will need to dynamically

balance your fan with balancing kit provided.

1. Check blue wire from fan to make sure it is connected to hot wire from house.

2. Check for loose or disconnected wires in fan switch housing.

3. Check for loose or disconnected wires in light kit.

4. Check for faulty lightbulb and make sure bulb is tight in socket.

5. Remove light kit and check the plug connections if they are present.

6. If this fan uses a remote controller, make sure dip switches are in the correct setting

and make sure the battery works.

CAUTION: Make sure main power is turned off before entering switch housing and/or

canopy.

2. If fan sounds noisy:

3. If fan wobbles:

4. If light does not work:

1. If fan does not start:

Trouble Suggested Remedy

Jan.2020

May.2020 Magnetic on transmitter, branding, canopy installation way

Aug.2021 update remote controller

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 4TK52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5BHM60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 8TNR56 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3DIR52RZWD-V1 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MGMR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CNR52XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MNLR56BSD Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MNLR56 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3IKR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CQM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3IKDR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ROR Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CSR60AGD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ERAR44 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DCR60XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DOR52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Centro Max 5CQM52-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CY60XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5OR52XXD-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DVR68 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Homeowner Max Plus 5HM52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4MC20XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TSR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ALMSM52 Series Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung