Monte Carlo Fan Company 3HYR56**D Series Bedienungsanleitung

Ceiling Fan Installation Instructions

57' &&!,70,8(48

!$"!!" #"!

Total fan weight

with light kit

% ?!

#

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes ANSI/NFPA 70-1999),

including fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding con-

ductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.

Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from

being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7

feet from the floor to the trailing edge of the blade.

To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support and

use only the screws provided with the outlet box. (Mounting must support at least 35 lbs.)

Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating

blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.

To reduce the risk of fire or electric shock, this fan should only be used with fan speed control part no. UC7067R manufactured by

Rhine Electronic Co., Ltd. Suitable for use with solid-state speed controls.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heat-

ing equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being

switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such

as a tag, to the service panel.

Air flow direction: warm weather - switch to left - forward / cool weather - switch to right - reverse

10.

11.

12.

13.

14.

WARNING: TO REDUCE THE RIS OF FIRE, ELECTRIC SHOC , OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

!"' "!

"! # 

Phillips Screwdriver Wire Cutters Pliers Step Ladder

Before you begin installing the fan, Switch

power off at Service panel and lock service dis-

connecting means to prevent power from being

switched on accidentally. When the service dis-

connecting means cannot be locked, securely

fasten a prominent warning device, such as a

tag, to the service panel.

Before installing this fan make sure the outlet box is

properly installed to the house structure. To reduce

the risk of fire, electric shock, or personal injury,

mount to outlet box or supporting system acceptable

for fan support. (Mounting must support at least 35

lbs.)



Installation

Use metal outlet box suitable for fan support

and use only the screws provided with the out-

let box (must support 35 lbs). Before attaching

fan to outlet box, ensure the outlet box is

securely fastened by at least two points to a

structural ceiling member ( a loose box will

cause the fan to wobble). #8,542>9/,8*7,<8

675;0+,+<09/9/,5:92,9)5=



Remove cotter pin from ball, and

save for later use.



Place canopy over down rod.

 

Place Yoke Cover over down rod.

Thread leadwires and safety cable

through the downrod.



Set dip switches on the Remote Transmitter and Remote

Receiver to the same settings. This must be done so the

units will communcate properly. If you have other fans you

can set to control from one transmitter by setting both

receivers the same as the transmitter. If you have more

than one fan with remote. You can set the dip switches to

different positiosns to have seperate control.

Remote Transmitter Dip swtiches

Remote Receiver Dip switches



white

black

Make wiring connections as indicated above.

White from fan to white from remote marked

N. Blue from fan to blue from remote

marked light. Black from fan to Black from

remote marked L. White from house to white

from remote marked AC N . Black from house

to Black from remote marked AC L. Connect

all green ground wires to Ground wire from

House.

blue

Green

white

black

House

Fan



fuse

Install remote receiver into the

mounting bracket.



Ready for wiring.



Make sure the studs protruding from the

bottom of the Mounting bracket are

installed with threads all the way through

the bracket.



Loosen the 2 screws on the yoke to

allow down rod to slip into yoke.



Insert down rod into yoke on top of

the fan body. Align the hole in the

down rod with the hole in the yoke.

Insert the Pin through the yoke and

down rod until the point appears on

the other side.



Install keeper pin.



Tighten the 2 set screws on the

yoke, once the down rod is in place.



Hang assembled fan from the mounting bracket

installed to ceiling in previous step. Make sure the

fan is hanging straight. Rotate fan until the tab on

the Mounting bracket engages the slot on the

Downrod Ball. This must be done to prevent the fan

body from rotating when the blades are in motion.



For Canadian installation and for USA fan and

light kit combinations over 35 lbs, in both flush

and downrod mode the safety cable must be

installed into the house structure beams using

the 3” lag screws,washers, and lock washers.

provided. Make sure that when the safety cable

is fully extended the leadwires are longer than

the cable and no stress is placed on the lead-

wires.

 Safety cable installation

!(-,9>()2,

(.!*7,<

safety

cable

3” lag

screw

lock

washer

Align keyslot holes of light kit plate

and twist the plate to lock. Install

the screw removed in step 22 and

tighten securely. Loosen two screws and remove one

screw from light plate. eep the

screw removed for later use.

 

Remove final nut, final cap, hex nut

and rubber washer from light kit.



Connect the white wire from fan to

white wire from light kit, then con-

nect the blue wire from fan to black

wire from light kit.



Aline keyslot holes of the light fixture

and twist it to lock. Install the screw

removed in step 24 and tighten

securely.



Install 3x40W bulbs provided.

*%(7404.: Over lamping the fan will

result in the fan lights shutting down till

the proper wattage of bulbs are installed.

Reset the lights by turning off the wall

switch, bracker, or by remote. Replace

bulbs with the correct wattage bulbs, turn

the power on*.



Lift canopy and install knurled nuts as

shown. Tighten the knurled nuts securely.

The canopy should adjust for any irregu-

larity in the ceiling or Outlet box.



Check motor for shipping stabilizers and

remove if present. Attached blades using

screws and fiber washers in hardware

pack. Tighten screws securely. Repeat this

procedure 4 more times.



Loosen two screws and remove one

screw. eep the screw removed for later

use.



Atathced the glass to light fitter.

Install the rubber washer and hex

nut which were removed from step

25 to the thread rod and secure the

glass.



Install the final cap and final nut which

were removed from step 25 to the thread

rod by screwing to secure the glass.

Make wire connections to power source using wire nuts

provided. Make sure that no filiments are outside of

the wirenut. After making the wire connections, the

wires should be spread apart with the grounded con-

ductor and the equipment-grounding conductor on one

side of the outlet box and ungrounded conductor on

the other side of the outlet box. The splices after being

made should be turned upward and pushed carefully

up into the outlet box.





Place face plate over battery compartment and

buttons. Place remote over 2 pins on front

cover. Attach cover of remote by placing over 4

pins and snapping into place. Install wall control unit to outlet box

using machine screws provided.

 HAND HELD INSTALL WALL MOUNT INSTALL

Attach front cover to wall control with

screws provided. Snap battery cover

in place.



Remove battery cover. Install 12V battery into

wall remote. Duracell MN21 / Eveready A23 / GP

23A all 12V.Attach cover of remote by placing

over buttons and snap the battery cover in

place.



,359,549752"7(483099,7

,(9:7,8

! Depress “l dot” for low speed, “2 dots” for medium or “3 dots” for

high. To turn fan off press square”.

" To turn light on, press light dimmer once quickly. To turn off

press once quickly while light is on. To dim light hold down button “light dimmer”.

The light will cycle from bright to dim to bright until button is released. Light will

maintain last setting if turned off.

 %  $ ! Depress rev button allow a few seconds for remote to

change rotation direction with fan running.

HIGH SPEED

MEDIUM SPEED

LOW SPEED

FAN OFF SETTING

(Turns fan off only)

FAN REVERSE

(Press once to

change direction of

the fan)Fanmust be

running to reverse.

LIGHT ON/OFF SET-

TING AND DIMMER

(Press and hold to

dim light infinitively)

LED LIGHT

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

#"(1,8:7,3(0465<,7089:74,+5--

3.Make sure forward/reverse switch is firmly in up or down position. Fan will not operate when switch

is in the middle.

4.Make sure that shipping stabilizer tabs have been removed from motor.

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each other or

against the interior wall of the switch housing.

#"(1,8:7,3(0465<,7089:74,+5--),-57,,49,704.8<09*//5:804.

4.Some fan motors are sensitive to signals from Solid State variable speed controls.

"#!(!520+!9(9,;(70()2,86,,+*549752

5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear after this

period.

1.Make sure that the ridge of the canopy engages the notch in the downrod ball. (See illustration in

Step #6 of Downrod Mount installation).

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and junc-

tion box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a

point on the ceiling above the tip of one of the blades. Measure this distance from blade tip to ceilng.

eeping measure within 1/8", rotate the fan until the next blade is positioned for measurement. Repeat

for each blade. If all blade levels are not equal, you can adjust blade levels by the following procedure.

To adjust a blade tip down, insert a washer (not supplied) between the blade and blade holder at the

screw closest to the motor. To adjust a blade tip up, insert washer (not supplied) between the blade and

blade holder at the two screws farthest from the motor. Reverse the position of the washer if blades

mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute

the weight and possibly result in smoother operation.

1.Check blue wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

%  ;,72(3604.9/,-(4<0227,8:29049/, -(420./988/:9904.+5<4 :4902

9/, 6756,7<(99(.,5-):2)8(7,0489(22,+ ,8,99/,20./98)>9:7404.5--9/,<(22

8<09*/)7,(1,757)>7,359, ,62(*,):2)8<09/9/,*577,*9<(99(.,):2)89:749/,65<,7

54

#"(1,8:7,3(0465<,7089:74,+5--),-57,,49,704.8<09*//5:804.(4+57

*(456>

% ,-57,(99,36904.957,62(*,9/,-:8,3(1,8:7,9/,3(0465<,7089:74,+5--95

9/,-(4 ,62(*,542><09/((36-:8,:8,080480+,9/,*(456>549/,)2:,<07,95

7,359,7,*,0;,76:8/(4+9<0899/,*(69556,49/,-:8,*(8,

2. If fan sounds noisy:

1. If fan does not start:

3. If fan wobbles:

4. If light does not work:

TROUBLE SHOOTING

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In

some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble

Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation, please call our

Customer Service Center at the

number printed on your parts list insert sheet.

%(7404.,-57,8,7;0*04.57*2,(404.:409!<09*/65<,75--(9!,7;0*,6(4,2(4+25*18,7;0*,+08*544,*904.

3,(489567,;,4965<,7-753),04.8<09*/,+54(**0+,49(22>%/,49/,8,7;0*,+08*544,*904.3,(48*(4459

),25*1,+8,*:7,2>-(89,4(675304,49<(7404.+,;0*,8:*/(8(9(.959/,8,7;0*,6(4,2

Trouble Suggested Remedy

Customer Service Center:

301 West Washington St.

Riverside,NJ 08075

1-800-519-4092

www.montecarlofans.com

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 5vsr44XXd-l series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3DIR52 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5STR52 Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company AC-572LF2000 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MAVR60 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5TV52XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5TLR54 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 14PRR62XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CQM52XX-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3NDR54XXD Series Technisches Dokument

Monte Carlo Fan Company

Monte Carlo Fan Company 5DCR52EP Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5OR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5BY52RB Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CSM60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company MC1215 Technisches Dokument

Monte Carlo Fan Company

Monte Carlo Fan Company 5SBR56XXD-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 8ATR44XXD-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4MC20 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MAVR60RZW Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HS52 D-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DS52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company AC-552 Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3VTR52D Series Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung