Morphy Richards CYCLONIC BAGLESS UPRIGHT VACUUM CLEANER Bedienungsanleitung

Cyclonic bagless

upright vacuum cleaner

Please read and keep these instructions

Dust canister

It is important to regularly empty the canister, even if it does not appear full.

Filters

It is important that the pleated filter is shaken clean each time the dust canister is emptied,

this allows air through the appliance. Wash the canister filters regularly in warm water and

allow to air dry.

Blockages

Check the hose, tubes and tools for blockages.

Safety cut-out

If the air-flow is blocked or the filters are not regularly cleaned, a thermostat may operate.

If this happens, switch off and disconnect from the mains supply. Clear any blockage,

empty and clean the filters. Allow 60 minutes for the thermostat to reset.

Belt

Check and replace damaged or broken belt.

Height adjustment

The height adjustment only comes into effect when the handle is released by the handle

release pedal.

Getting the best from your new cleaner...

If your cleaner is not picking up as well as it should, please check

VC73337 MUK Rev 1

If you have a problem or complaint, please call our dedicated UK based helpline

before returning your product to the retailer from where it was purchased.

UK Helpline: 0844 871 0949

Replacement Parts: 0844 873 0715

Ireland Helpline: 1800 409 119

73337 rev1 29/10/08 16:05 Page 1

IMPORTANT

SAFETY

INSTRUCTIONS

The use of any electrical

appliance requires the

following common sense

safety rules.

Primarily there is danger of

injury or death and secondly

the danger of damage to the

appliance.

Please read these

instructions before using the

cleaner.

Location

• Do not use or keep this

product outside.

• Do not store the appliance

near hot surfaces eg. ovens

or heating appliances.

Mains lead

• Do not allow the mains lead

to become strained or run

this appliance over it.

• If the electrical cable

becomes damaged, the

cable assembly must be

replaced. Do not attempt this

task yourself, contact the

helpline number that is found

at the bottom of the page.

Personal safety

• WARNING: Keep loose

clothing, hair, fingers etc.

away from the floor

nozzle whenever the

cleaner is connected to

the mains.

• WARNING: Only lift the

product by the handles

‡and ‰.

• Disconnect from the

mains supply before

attempting to clear

blockages, clear the

brush or replace the belt.

• Disconnect from the mains

supply before cleaning or

emptying the appliance.

• Never modify the cleaner in

any way.

• Never use in the presence of

explosive liquid or vapours.

• Never pick up inflammable or

poisonous liquids such as

petrol, copier toner or other

volatile substances. Never

pick up acids, asbestos or

asbestos dust.

• Never touch the plug or

cable with wet hands.

• Unprofessional repairs can

be dangerous for users.

• Use only Morphy Richards

spare parts and accessories.

• The appliance must never be

left running unsupervised.

• This appliance is intended for

domestic use only. Misuse or

use for commercial or any

other purpose will render the

guarantee invalid.

• Always disconnect the

appliance from the mains

supply after use.

• This appliance is not

intended for use by persons

(including children) with

reduced physical, sensory or

mental capabilities, or lack of

experience and knowledge,

unless they have been given

supervision or instruction

concerning use of the

appliance by a person

responsible for their safety.

• To protect against fire,

electric shock and personal

injury, do not immerse cord,

plug or cleaner in water or

other liquid.

Product safety

• Never use the appliance

without the filters being

installed.

• Never use the appliance to

vacuum hot ashes, broken

glass, sharp objects or

liquids.

• Never over-extend the hose

such that the cleaner is

pulled over. If the cleaner is

knocked over, switch off

before attempting to upright.

• Never pick the cleaner up by

the floor nozzle when

connected to the mains, use

the carrying handle.

Children

• Children do not understand

the dangers associated with

operating electrical

appliances. Never allow

children to use this

appliance.

• Children should be

supervised to ensure that

they do not play with the

appliance, or stumble over

the power cord.

Electrical

requirements

Check that the voltage on the

rating plate of your appliance

corresponds with your house

electricity supply which must

be A.C. (Alternating current).

If the socket outlets in your

home are not suitable for the

plug supplied with this

appliance, the plug should

be removed and the

appropriate one fitted.

WARNING: The plug

removed from the mains

lead, if severed, must be

destroyed, as a plug with

a bared flexible cord is

hazardous if engaged

into a live socket outlet.

Should the fuse in the 13

amp plug require changing, a

13 amp BS1362 fuse must

be fitted.

UUKKHHeellpplliinnee0088444488771100994499RReeppllaacceemmeennttPPaarrttss0088444488773300771155IIrreellaannddHHeellpplliinnee11880000440099111199

73337 rev1 29/10/08 16:05 Page 2

⁄

‹

›

ﬂ

‡

‚



ÎÒ

„

ﬁ

‰

FEATURES

⁄Eco Switch

¤Front cover release

‹Removable front cover

›Exhaust filter grille

ﬁCarpet height adjustment

knob

ﬂFloor nozzle with powered

brush

‡Upper handle

·Flexible hose

‚Cord storage with quick

release cleat

„On/Off switch

‰Carrying handle

ÂNested extension tubes (x2)

ÊCrevice nozzle

ÁFurniture brush

ËHose clip

ÈHose clip slot

ÍHandle release pedal

ÎHose end connector

ÏDust canister release

(shown page 5)

ÌDust canister lid

ÓPleated circular filter

ÔCentral mesh filter

Canister handle

ÒDust canister

ÚTurbo nozzle

ÛHard Floor nozzle

ÙStair tool

ıHair tool

ˆSoft dusting brush

˜Stubborn dirt brush

¯Upholstery nozzle

FFoorrddeettaaiillssooffootthheerrMMoorrpphhyyRRiicchhaarrddsspprroodduuccttss,,pplleeaasseesseeeeoouurrwweebbssiittee::

Ûı

73337 rev1 29/10/08 16:05 Page 3

OPERATING THE

APPLIANCE

Assembly A

WARNING: Do not plug in the

cleaner until it is assembled.

1Carefully unpack all of the

components.

2Lift the cleaner body to the

upright position.

3Remove the two screws that are

already attached to the body.

4From the rear of the cleaner, align

the handle with the groove and

slide into the body. If necessary,

use thumb and finger pressure to

slide the handle into position.

5Fasten the handle with the two

screws.

Floor nozzle

height adjustment B

Before using the cleaner, the floor

nozzle height ﬁ must be set to

the correct height.

Choose the setting which most

closely matches your floor

surface.

• Use the TOOLS setting when

using the tools.

Note: The height adjustment only

comes into effect when the

handle is released by the handle

release pedal Í.

Eco Switch C

The Eco Switch ⁄ allows you to

turn down the power when

cleaning more delicate items,

such as curtains and upholstery,

saving energy and reducing costs.

Using on carpets

1Place the cleaner in it’s upright

position.

2Set the carpet height adjustment

knob ﬁ to the desired position.

3Release the mains cable by

revolving the quick release cleat

‚half-a-turn and extend the

cable fully.

4Plug the cable into the mains

socket.

5Step on the handle release pedal

Í to release the handle to the

desired position.

6Press the on/off switch

„

to the

‘on’ position.

IMPORTANT: To prevent damage

to carpets, never leave the cleaner

switched on in one place for an

extended period.

• Never have the brushes set too

low such that the cleaner is hard

to push.

Using the

attachments

Follow steps 1-4but set the

carpet height adjustment knob to

the TOOLS setting.

5Remove the hose connector Î

from the rear of the cleaner. Lift

the hose ·from the top handle

hook. Insert the hose clip Ëinto

the hose clip slot È.

• Push the required attachment

firmly onto the end of the hose.

• If additional length is required,

attach one or both extension

tubes Â.

6Switch on „.

UUKKHHeellpplliinnee0088444488771100994499RReeppllaacceemmeennttPPaarrttss0088444488773300771155IIrreellaannddHHeellpplliinnee11880000440099111199

ﬁ

⁄

73337 rev1 29/10/08 16:05 Page 4

• IMPORTANT: Always fix the hose

clip Ëto the main body slot È

when using the hose and tools.

• Never over extend the hose such

that the cleaner is pulled over.

IMPORTANT: Turning the cleaner

sideways helps prevent the

cleaner being pulled along by the

stretch hose.

Using the hardfloor

nozzle

Attach the hardfloor nozzle Ûto

the two separate attachable

tubes.

This nozzle is ideal for use on

wood, laminate, tile and vinyl

flooring.

Using & cleaning the

turbo nozzle

Attach the turbo nozzle Úto the

hose end connector

only. For

use on upholstery and stairs.

WARNING: The turbo nozzle

should not be used with the

extension tubes. Attach to

the hose handle only.

Following use, your turbo nozzle

may become clogged. Ensure the

vacuum cleaner is switched off

and the turbo nozzle is detached

from the hose. Turn over the

nozzle and pull away any hairs or

fibres. If they are tightly wound

around the brush, carefully snip

the fibres with scissors, being

careful not to damage the brush

bar, pull away from the brush bar

and dispose.

To aid cleaning, the turbo nozzle

can be opened up by pushing the

button on the nozzle forwards.

Using the accessories

Attach the crevice nozzle Ê to

the hose end connector

tubes

to access narrow or

hard to reach places.

Attach the

furniture brush Á

the hose end connector

tubes

for use on pelmets,

delicate objects etc.

Attach the stair tool Ù to the

hose end connector

for

effective stair cleaning D.

Attach the hair tool ı to the stair

tool

for fantastic pet hair

pick-up D.

Attach the soft dusting brush ˆ

to the stair tool

for a softer

pick-up D.

Attach the stubborn dirt brush

to the stair tool

to attack

stubborn ground in dirt D.

Attach the upholstery

nozzle

to the stair tool

for effective

upholstery cleaning D.

EMPTYING

Empty the dust canister regularly

even if it does not look full, this

will maintain the performance.

1Remove the front cover ‹ by

lifting the cover release lever ¤

2Lift-up the dust canister release

Ïand pull the canister away

from the main body.

3Take the canister to the dustbin.

4Turn the lid quarter-of-a-turn

anti-clockwise to unlock, lift off

the lid with pleated filter Ó, put to

one side F.

5Lift out the central mesh filter Ô

from the dust canister Ò G.

Brush clean if necessary.

6Empty out the dust canister Ò.

FFoorrddeettaaiillssooffootthheerrMMoorrpphhyyRRiicchhaarrddsspprroodduuccttss,,pplleeaasseesseeeeoouurrwweebbssiittee::

73337 rev1 29/10/08 16:05 Page 5

7Re-fit the central mesh filter.

8Shake the pleated filter Ó to

remove all dust.

9Re-fit pleated filter with lid into the

dust canister by lining up the two

arrows and turning the lid quarter-

of-a-turn clockwise to lock.

10 Re-fit dust canister into cleaner

and push to lock into position.

11 Re-fit the front cover.

SAFETY CUT-OUT

If the cleaner overheats, a motor

protection thermostat will

automatically switch the motor off.

If this happens, switch the

cleaner off, unplug from the

power supply and leave the

cleaner to cool for at least 60

minutes. Check the airways for

blockages, empty the dust

canister and clean the filters

before restarting.

CLEANING THE

FILTERS

To maintain suction, the

pleated filter

must be

shaken clean each time the

dust canister is emptied.

Failure to clean the filter will

reduce suction and could damage

the motor if used for a prolonged

period. This may invalidate the

guarantee. If the filters become

damaged, they must be replaced.

Pleated filter

Clean the pleated filter every time

the canister is emptied to

maintain high performance

. To

thoroughly clean it, wash it

regularly.

To remove it from the dust

canister lid, turn the filter quarter-

of-a-turn anti-clockwise H. Wash

in warm water (no detergent) and

allow to air dry before refitting.

Motor protection filter

The motor protection filter ˘is

located underneath the dust

canister.

1Remove the dust canister.

2Lift out the filter and shake over a

dustbin.

The filter may also be washed in

water (no detergents). Allow the

filter to air dry. Ensure the filter is

thoroughly dry before refitting.

3Replace the filter I.

Exhaust filter J

The exhaust filter is located below

the dust canister compartment.

1Remove the front cover ‹.

2Remove the exhaust filter ◊by

pulling forward at the top and

lifting it away.

3Take the filter out of the cage and

shake vigorously over a dustbin.

The filter may also be washed in

warm water. Do not use

detergents. The filter must be

completely dry before re-fitting.

Allow filters to air dry naturally.

4Replace the filter and the front

cover.

Changing the belt

If the brush bar stops rotating, it is

likely that the drive belt has

snapped (usually because the

brush has been stalled). A spare

belt is supplied. Replacement

belts can also be obtained from

Morphy Richards by calling the

helpline number at the base of the

page.

Accessing the floor

nozzle K

1Disconnect the cleaner from the

mains supply.

2Put the switch to the ‘off’ position.

3Remove the front cover and the

dust canister.

UUKKHHeellpplliinnee0088444488771100994499RReeppllaacceemmeennttPPaarrttss0088444488773300771155IIrreellaannddHHeellpplliinnee11880000440099111199

◊

73337 rev1 29/10/08 16:06 Page 6

4Press the handle release pedal

and place the cleaner face down,

in a flat position on a soft surface

(eg. carpet).

5Using a flat bladed screwdriver or

a coin, rotate the three cover

fixings, a quarter-of-a-turn, from

lock to unlock K.

6Lift the base cover from the

rear fixing area first, the cover will

rotate forward. Unhook the cover

from the front edge and remove.

Removing rotating

brush & belt L,M

7Lift the metal belt guard out of

the floor nozzle and put it safely

to one side L.

8Slide the belt past the end of the

motor drive shaft . If the belt

has broken, remove all pieces and

clean the drive shaft.

9Lift the rotating brush equally

at both ends to slide it free of the

floor nozzle M. Holding the ends

of the brush, check it rotates

freely or not, if not, it must be

replaced. Call our Helpline for

replacement parts or belts.

Re-fitting rotating

brush & belt N

10 Hook the belt over the drive

shaft (the belt must be slid

sideways past the end of the drive

shaft). Note: The belt guard must

have been removed first, see

point 7 above.

11 Refit the belt guard, ensuring it is

correctly located. Press down

fully.

12 Pass the rotary brush through the

belt, ensuring the correct end is

located against the belt N.

13 Pull the brush forward (against the

pull of the belt) and locate the

square ends of the brush into

location slots in the floor nozzle

14 Rotate the brush by hand to

ensure the belt is running in the

centre of it’s location on the

brush.

Refitting the floor

nozzle base cover O

15 Hook the base cover into the

front of the floor nozzle, ensuring

all four hooks are engaged O.

16 Rotating the cover downwards

and rearwards, slowly close the

cover.

17 Tighten the three fixings, using a

screwdriver to turn the fixings a

quarter-of-a-turn to the lock

position.

Note: If the cover will not fully

close or fixings will not lock, lift

the cover slightly and rotate the

fixings until they are in the correct

position for closure.

18 Return the cleaner to the upright

position, re-fit the dust canister

and front cover. Connect to the

mains supply. Switch on to test.

HELPLINE

If you have any difficulty with your

appliance, do not hesitate to call

us.

We are more likely to be able to

help than the store from where

you bought it.

Please have the following

information ready to enable our

staff to deal with your query

quickly.

• Name of the product

• Model number as shown on the

underside of the appliance.

• Serial number as shown on

underside of the appliance.

WEBSITE

You may also contact us through

our website, or visit the site to

browse and purchase appliances,

spare parts and accessories from

the extensive Morphy Richards

range.

FFoorrddeettaaiillssooffootthheerrMMoorrpphhyyRRiicchhaarrddsspprroodduuccttss,,pplleeaasseesseeeeoouurrwweebbssiittee::

UK Helpline 0844 871 0949

Replacement Parts 0844 873 0715

Ireland Helpline 1800 409 119

73337 rev1 29/10/08 16:06 Page 7

Morphy Richards products are intended for household use only.

Morphy Richards has a policy of continuous improvement in product quality and

design. The company therefore reserves the right to change the specification of

it’s models at any time.

The After Sales Division

Morphy Richards Ltd

Mexborough, SouthYorkshire,

England, S64 8AJ

Helplines (office hours)

UK 0844 871 0949

Spare Parts 0844 873 0715

Republic of Ireland 1800 409 119

VC73337 MUK Rev 1 10/08

YOUR TWO YEAR

GUARANTEE

It is important to retain the

retailer’s receipt as proof of

purchase. Staple your receipt

to this back cover for future

reference.

Please quote the following

information if the product

develops a fault. These

numbers can be found on

the base of the product.

Model no.

Serial no.

All Morphy Richards

products are individually

tested before leaving the

factory. In the unlikely event

of any appliance proving to

be faulty within 28 days of

purchase, it should be

returned to the place of

purchase for it to be

replaced.

If the fault develops after 28

days and within 24 months

of original purchase, you

should contact the helpline

number quoting model

number and serial number on

the product, or write to

Morphy Richards at the

address shown.

You will be asked to return

the product (in secure,

adequate packaging) along

with a copy of proof of

purchase.

Subject to the exclusions set

out below (1-7), the faulty

appliance will then be

repaired or replaced and

dispatched usually within

seven working days of

receipt.

If, for any reason, this item is

replaced during the 2 year

guarantee period, the

guarantee on the new item

will be calculated from

original purchase date.

Therefore, it is vital to retain

your original receipt or

invoice to indicate the date of

initial purchase.

To qualify for the two-year

guarantee, the appliance

must have been used

according to the

manufacturer’s instructions.

For example, the filters must

have been regularly cleaned

as instructed.

Morphy Richards shall not be

liable to replace or repair the

goods under the terms of the

Guarantee where:

EXCLUSIONS

1The fault has been caused or

is attributable to accidental

use, mis-use, negligent use

or used contrary to the

manufacturer’s

recommendations or where

the fault has been caused by

power surges or damage

caused in transit.

2The appliance has been used

on a voltage supply other

than that stamped on the

products.

3Repairs have been attempted

by persons other than our

service staff (or authorised

dealer).

4The appliance has been used

for hire purposes or non-

domestic use.

5The appliance is second

hand.

6Morphy Richards are not

liable to carry out any type of

servicing work under the

guarantee.

7Consumables such as the

filters and belt are not

covered by the guarantee.

• This guarantee does not

confer any rights other than

those expressly set out

above and does not cover

any claims for consequential

loss or damage. This

guarantee is offered as an

additional benefit and does

not affect your statutory

rights as a consumer.

• This guarantee is valid in the

UK and Ireland only.

For electrical products sold within the

European Community. At the end of the

electrical products useful life, it should

not be disposed of with household

waste.

Please recycle where facilities exist.

Check with your Local Authority or

retailer for recycling advice in your

country.

73337 rev1 29/10/08 16:06 Page 8

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Morphy Richards Staubsauger Handbücher

Morphy Richards

Morphy Richards POD COMPACT BAGLESS VACUUM CLEANER - REV 2 Bedienungsanleitung

Morphy Richards

Morphy Richards IB73340 Bedienungsanleitung

Morphy Richards

Morphy Richards Scoot bagless vacuum cleaner Bedienungsanleitung

Morphy Richards

Morphy Richards Storm hard floor cylinder vacuum cleaner Bedienungsanleitung

Morphy Richards

Morphy Richards IB73090 Bedienungsanleitung

Morphy Richards

Morphy Richards Supervac deluxe Bedienungsanleitung

Morphy Richards

Morphy Richards Scoot cylinder vacuum cleaner Bedienungsanleitung

Morphy Richards

Morphy Richards LOX VACUUM CLEANER Bedienungsanleitung

Morphy Richards

Morphy Richards IB71050 Bedienungsanleitung

Morphy Richards

Morphy Richards Upright and Handheld Steam Cleaner Bedienungsanleitung

Morphy Richards

Morphy Richards Boxer wet & dry vacuum cleaner Bedienungsanleitung

Morphy Richards

Morphy Richards Allergy cylinder vacuum cleaner Bedienungsanleitung

Morphy Richards

Morphy Richards 73281 Bedienungsanleitung

Morphy Richards

Morphy Richards Supervac Deluxe Bedienungsanleitung

Morphy Richards

Morphy Richards ESSENTIALS COMPACT BAGLESS VACUUM CLEANER Bedienungsanleitung

Morphy Richards

Morphy Richards 73332 Bedienungsanleitung

Morphy Richards

Morphy Richards Supervac Bedienungsanleitung

Morphy Richards

Morphy Richards 73199 Bedienungsanleitung

Morphy Richards

Morphy Richards Ecovac vacuum cleaner Bedienungsanleitung

Morphy Richards

Morphy Richards PerformAir Upright Vacuum Bedienungsanleitung

Morphy Richards

Morphy Richards ESSENTIALS CYLINDER VACUUM CLEANER - REV 3 Bedienungsanleitung

Morphy Richards

Morphy Richards POD CYCLONE VACUUM CLEANER - REV 1 Bedienungsanleitung

Morphy Richards

Morphy Richards Bagless Cylinder Vacuum Cleaner Bedienungsanleitung

Morphy Richards

Morphy Richards Essentials Family and Pets+ Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch