Morphy Richards CYCLONIC BAGLESS VACUUM CLEANER

www.morphyrichards.com

Cyclonic bagless vacuum cleaner

Please read and keep these instructions

Getting the best from your new cleaner...

If your cleaner is not picking up as well as it should, please check

Dust canister

It is important to regularly empty the canister even if it does not appear full.

Filters

It is important that the pleated filter is shaken clean each time the dust canister is

emptied to allow air through the appliance. Wash the canister filters regularly in warm

water and allow to air dry. A spare pleated filter is included.

Blockages

Check the hose, tubes and tools for blockages

Safety cut-out

If the air-flow is bloked or the filters are not regulary cleaned a thermostat may operate. If

this happens, switch off and disconnect from the mains supply. Clear any blockage,

empty and clean the filters. Allow 60 minutes for the thermostat to reset.

Belt

Check and replace damaged or broken belt

Height adjustment

The height adjustment only comes into effect when the handle is released by the handle

release pedal È.

VC73360MUK Rev 4

For replacement parts, help with using your Morphy Richards, problems

and lots more, contact us by phone or through our website.

UUKKHHeellpplliinnee::0088770000660022660044

RReeppllaacceemmeennttppaarrttss::0088770011667766663355

IIrreellaanndd11880000440099111199

73360 rev4 11/7/06 14:43 Page 1

IMPORTANT

SAFETY

INSTRUCTIONS

The use of any electrical

appliance requires the

following common sense

safety rules.

Primarily there is danger of

injury or death and

secondly the danger of

damage to the appliance.

Location

• Do not use or keep this

product outside in the rain.

• Do not store the appliance

near hot surfaces eg ovens

or heating appliances.

Mains lead

• Do not allow the mains

lead to become strained or

run this appliance over it.

• If the electrical cable

becomes damaged the

cable assembly must be

replaced. Do not attempt

this task yourself, contact

the helpline number that is

found at the bottom of the

page.

Personal safety

• WARNING: Keep loose

clothing, hair, fingers

etc. away from the floor

nozzle whenever the

cleaner is connected to

the mains.

• Disconnect from the

mains supply before

attempting to clear

blockages, clear the

brush or replace the

belt.

• Disconnect from the mains

supply before cleaning or

emptying the appliance.

• Never modify the cleaner in

any way.

• Never use in the presence

of explosive liquid or

vapours.

• Never pick up inflammable

or poisonous liquids such

as petrol, copier toner or

other volatile substances.

Never pick up acids,

asbestos or asbestos dust.

• Never touch the plug or

cable with wet hands.

• Unprofessional repairs can

be dangerous for users.

• Use only Morphy Richards

spare parts and

accessories.

• The appliance must never

be left running

unsupervised.

• This appliance is intended

for domestic use only.

Misuse or use for

commercial or any other

purpose will render the

guarantee invalid.

• Always disconnect the

appliance from the main

supply after use.

• To protect against fire,

electric shock and personal

injury do not immerse cord,

plug or cleaner in water or

other liquid.

Product safety

• Never use the appliance

without the filters being

installed.

• Never use the appliance to

vacuum hot ashes, broken

glass, sharp objects or

liquids.

• Never over-extend the hose

such that the cleaner is

pulled over. If the cleaner is

knocked over, switch off

before attempting to

upright.

• Never pick the cleaner up

by the floor nozzle when

connected to the mains,

use the carrying handle.

Children

• Children do not understand

the dangers associated

with operating electrical

appliances. Never allow

children to use this

appliance.

Electrical

requirements

Check that the voltage on

the rating plate of your

appliance corresponds with

your house electricity

supply which must be A.C.

(Alternating current).

If the socket outlets in your

home are not suitable for

the plug supplied with this

appliance the plug should

be removed and the

appropriate one fitted.

WARNING: The plug

removed from the

mains lead, if severed,

must be destroyed as a

plug with a bared

flexible cord is

hazardous if engaged

into a live socket

outlet.

Should the fuse in the 13

amp plug require changing

a 13 amp BS1362 fuse

must be fitted.

UUK Helpline 0870 060 2604 Replacement Parts 0870 167 6635 Ireland Helpline 1800 409119

73360 rev4 11/7/06 14:43 Page 2

FEATURES

⁄Vari power slider (certain

models only)

¤Front cover release

‹Removable front cover

›Exhaust filter grille

ﬁCarpet height adjustment

knob

ﬂFloor nozzle with powered

brush

‡Upper handle

·Flexible hose

‚Cord storage with quick

release cleat

„On/Off switch

‰Carrying handle

ÂNested extension tubes (2)

ÊCrevice nozzle

ÁFurniture brush

ËHose clip slot

ÈHandle release pedal

ÍHose connector

ÎDust canister release

(shown page 5)

ÏDust canister lid

ÌPleated circular filter

ÓDust canister

ÔCentral mesh filter

Canister handle

ÒMotor protection filter

(shown page 6)

ÚExhaust filter (page 6)

ÛBelt cover (shown page 7)

ÙBrush bar (page 7)

ıMotor shaft (shown page 7)

ˆBrush bar end caps (shown

page 7)

˜Hose clip

¯Turbo nozzle (certain

models only)

˘Belt guard (shown page 7)

⁄

‹

›

ﬂ

‡

‚



www.morphyrichards.com

„

ﬁ

‰

73360 rev4 11/7/06 14:43 Page 3

4UK Helpline 0870 060 26 Replacement Parts 0870 167 6635 Ireland Helpline 1800 409119

OPERATING THE

APPLIANCE

Assembly A

WARNING: Do not plug in

the cleaner until it is

assembled.

1Carefully unpack all

components.

2Lift cleaner body to upright

position.

3Remove the two screws that are

already attached to the body.

4From the rear of the cleaner,

align the handle with groove and

slide into the body. If necessary,

use thumb and finger pressure

to slide handle into position.

5Fasten the handle with the two

screws.

Floor nozzle

height adjustment B

Before using the cleaner the

floor nozzle height must be set

to the correct height.

Choose the setting which most

closely matches your floor

surface.

• Use the TOOLS setting when

using the tools.

Note: The height adjustment

only comes into effect when the

handle is released by the handle

release pedal ť.

Variable power C

(Certain models only)

Slide the variable power control

to the right to increase the

suction power or to the left to

decrease suction. This feature is

most useful when using the

hose and accessories. Use the

minimum setting when

vacuuming delicate

fabrics/curtains etc. When not

using the hose it is advisable to

keep the variable slider set to

maximum.

Using on carpets

1Place cleaner in its upright

position.

2Set the carpet height

adjustment knob to the desired

position.

3Release the mains cable by

revolving the quick release cleat

1/2 a turn and extend the cable

fully.

4Plug the cable into the mains

socket.

5Step on the handle release

pedal to release the handle to

the desired position.

6Press the on/off button to the

‘on’ position.

IMPORTANT: To prevent damage

to carpets, never leave the

cleaner switched on in one

place for an extended period.

• Never have the brushes set too

low such that the cleaner is hard

to push.

Using

attachments

Follow steps 1-4 but set the

carpet height adjustment knob

to the TOOLS setting.

5Remove the hose connector Í

from the rear of the cleaner. Lift

the hose ·from the top handle

hook. Insert the hose clip ų into

the hose clip slot Ë.

• Push the required attachment

firmly onto the end of the hose.

min max

73360 rev4 11/7/06 14:43 Page 4

www.morphyrichards.com

• If additional length is required,

attach one or both extension

tubes.

6Switch on/off.

• IMPORTANT: Always fix the

hose clip ˜to the main body

slot Ëwhen using the hose and

tools.

• Never over extend the hose

such that the cleaner is pulled

over.

IMPORTANT: Turning the cleaner

sideways helps prevent the

cleaner being pulled along by

the stretch hose.

Using & cleaning

turbo nozzle

(Certain models only)

Attach the turbo nozzle to the

hose end connector Í for use on

upholstery and stairs.

After use your turbo nozzle may

become clogged. Turn over the

nozzle and pull away any hairs

or fibres. If they are tightly

wound around the brush

carefully snip the fibres with

scissors, being careful not to

damage the brush bar, pull away

from the brush bar and dispose.

EMPTYING

Empty the dust canister

regularly even if it does not look

full this will maintain the

performance.

1Remove the front cover by lifting

the cover release lever ¤ E.

2Lift-up the dust canister release

Îand pull the canister away

from the main body.

3Take the canister to the dustbin.

4Turn the lid 1/4 turn anti-

clockwise to unlock, lift off the

lid with pleated filter, Ìput to

one side. F

5Lift out the central mesh filter Ô

from the dust canister Ó G.

Brush clean if necessary.

6Empty out the dust canister Ó.

7Re-fit the central mesh filter.

8Shake the pleated filter to remove

all dust.

9Re-fit pleated filter with lid into

the dust canister by lining up the

two arrows and turning the lid

1/4 turn clockwise to lock.

10 Re-fit dust canister into cleaner

and push to lock into position.

Then re-fit front cover.

73360 rev4 11/7/06 14:43 Page 5

6UK Helpline 0870 060 2604 Replacement Parts 0870 167 663 Ireland Helpline 1800 409119

SAFETY CUT-OUT

If the cleaner overheats a motor

protection thermostat will

automatically switch the motor

off. If this happens, switch the

cleaner off, unplug from the

power supply and leave the

cleaner to cool for at least

60 minutes. Check the

airways for blockages, empty

dust canister and clean the

filters before restarting.

CLEANING THE

FILTERS

To maintain suction the

pleated filter must be

shaken clean each time the

dust canister is emptied.

Failure to clean the filter will

reduce suction and could

damage the motor if used for a

prolonged period. This may

invalidate the guarantee. If the

filters become damaged they

must be replaced.

Pleated filter

This must be shaken clean at

every emptying to maintain

suction. To thoroughly clean it

wash it regularly.

To remove it from the dust

canister lid turn the filter 1/4

turn anti-clockwise. GWash in

warm water (no detergent) and

allow to air dry before refitting.

The spare pleated filter allows

one filter to be washed and

dried whilst the other is in use.

Motor protection filter

The motor protection filter Òis

located underneath the dust

canister

1Remove the dust canister.

2Lift out the filter and shake over

a dustbin.

The filter may also be washed in

water (no detergents) but must

be totally dry before re-fitting.

3Replace the filter

Exhaust filter I

The exhaust filter is located

below the dust canister

compartment.

1Remove the front cover.

2Remove the exhaust filter Úby

pulling forward at the top and

lift it away.

3Take the filter out of the cage

and shake vigorously over a

dustbin. The filter may also be

washed in warm water. Do not

use detergents. The filter must

be completely dry before re-

fitting. Allow filters to air dry

naturally.

4Replace the filter and front

cover.

Changing the belt

If the brush bar stops rotating it

is likely that the drive belt has

snapped (usually because the

brush has been stalled). A spare

belt is supplied. Replacement

belts can also be obtained from

Morphy Richards.

Accessing the floor

nozzle I

1Disconnect the cleaner from the

mains supply.

2Put switch to off position.

3Remove front cover and dust

canister.

4Press the handle release pedal

and place the cleaner face

down, in a flat position on a soft

surface (eg carpet).

5Using a flat bladed screwdriver

or a coin, rotate the three cover

fixings, a quarter of a turn, from

lock to unlock I .

6Lift the base cover, from the rear

fixing area first, the cover will

rotate forward. Unhook cover

from front edge and remove M.

73360 rev4 11/7/06 14:43 Page 6

www.morphyrichards.com

Removing rotating

brush & belt K

7Lift the metal belt guard ˘out

of the floor nozzle and put it

safely to one side J.

8Slide the belt past the end of the

motor drive shaft. If the belt has

broken remove al pieces and

clean the drive shaft.

9Lift the rotating brush equally at

both ends to slide it free of the

floor nozzle K. Holding the

ends of the brush check it

rotates freely or not, it must be

replaced. Call our Helpline for

replacement parts or belts.

Re-fitting rotating

brush & belt L

10 Hook the belt over the the drive

shaft (the belt must be slid

sideways past the end of the

drive shaft). Note: Belt guard

must have been removed first,

see 7 above.

11 Refit the belt guard, ensuring it

is correctly located. Press down

fully.

12 Pass the rotary brush through

the belt ensuring the correct end

is located against the belt. M

13 Pull the brush forward (against

the pull of the belt) and locate

the square ends of the brush

into location slots in the floor

nozzle M.

14 Rotate the brush by hand to

ensure the belt is running in the

center of its location on the

brush.

Refitting floor nozzle

base cover M

15 Hook the base cover into the

front of the floor nozzle,

ensuring all four hooks are

engaged M.

16 Rotating the cover downwards

and rearwards, slowly close the

cover.

17 Tighten three fixings, using

screwdriver to turn fixings a

quarter of a turn to the lock

position.

Note: If the cover will not fully

close or fixings will not lock, lift

the cover slightly and rotate

fixings until they are in the

correct position for closure.

18 Return cleaner to the upright

position, re-fit dust canister and

front cover. Connect to the

mains supply. Switch on to test.

HELPLINE

If you have any difficulty with

your appliance, do not hesitate

to call us.

We are more likely to be able to

help than the store from where

you bought it.

Please have the following

information ready to enable our

staff to deal with your query

quickly.

• Name of the product

• Model number as shown on the

underside of the appliance.

• Serial number as shown on

underside of the appliance.

UUKK

HHeellpplliinnee0088770000660022660044

RReeppllaacceemmeennttPPaarrttss0088770011667766663355

IIrreellaannddHHeellpplliinnee11880000440099111199

73360 rev4 11/7/06 14:43 Page 7

Morphy Richards products are intended for household use only.

Morphy Richards has a policy of continuous improvement in product quality and

design. The company, therefore reserves the right to change the specification of its

models at any time.

The After Sales Division

Morphy Richards Ltd

Mexborough, SouthYorkshire,

England, S64 8AJ

Helpline (office hours)

UK 0870 060 2604

Republic of Ireland 1800 409119

VC73360MUK Rev4 07/06

FFoorrddeettaaiillssooffootthheerrpprroodduuccttssiinntthheeMMoorrpphhyyRRiicchhaarrddssrraannggeepplleeaasseesseeeeoouurrwweebbssiittee......

wwww.morphyrichards.com

YOUR TWO YEAR

GUARANTEE

It is important to retain the

retailers receipt as proof of

purchase. Staple your

receipt to this back cover

for future reference.

Please quote the following

information if the product

develops a fault. These

numbers can be found on

the base of the product.

Model no.

Serial no.

All Morphy Richards

Products are individually

tested before leaving the

factory. In the unlikely event

of any appliance proving to

be faulty within 28 days of

purchase it should be

returned to the place of

purchase for it to be

replaced.

If the fault develops after

28 days and within 24

months of original

purchase, you should

contact the helpline

number quoting model

number and serial number

on the product, or write to

Morphy Richards at the

address shown.You will be

asked to return the product

(in secure, adequate

packaging) along with a

copy of proof of purchase.

Subject to the exclusions

set out below (1-6), the

faulty appliance will then

be repaired or replaced

and dispatched usually

within seven working days

of receipt.

If for any reason this item is

replaced during the 2-year

guarantee period, the

guarantee on the new item

will be calculated from

original purchase date.

Therefore it is vital to retain

your original receipt or

invoice to indicate the date

of initial purchase.

To qualify for the two-year

guarantee the appliance

must have been used

according to the

manufacturers instructions.

For example the filters shall

have been regularly

cleaned as instructed.

Morphy Richards shall not

be liable to replace or

repair the goods under the

terms of the Guarantee

where:

EXCLUSIONS

1The fault has been caused

or is attributable to

accidental use, mis-use,

negligent use or used

contrary to the

manufacturers

recommendations or where

the fault has been caused

by power surges or

damage caused in transit.

2The appliance has been

used on a voltage supply

other than that stamped on

the products.

3Repairs have been

attempted by persons

other than our service staff

(or authorised dealer).

4Where the appliance has

been used for hire

purposes or non-domestic

use.

5Morphy Richards are not

liable to carry out any type

of servicing work, under

the guarantee.

6Consumables such as the

filters and belt are not

covered by the guarantee.

This guarantee does not

confer any rights other than

those expressly set out

above and does not cover

any claims for

consequential loss or

damage. This guarantee is

offered as an additional

benefit and does not affect

your statutory rights as a

consumer.

• This guarantee is valid in

the UK and Ireland only.

For electrical products sold within the

European Community. At the end of the

electrical products useful life it should

not be disposed of with household

waste.

Please recycle where facilities exist.

Check with your Local Authority or

retailer for recycling advice in your

country.

73360 rev4 11/7/06 14:43 Page 8

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Morphy Richards Staubsauger Handbücher

Morphy Richards

Morphy Richards SpillMaster Bedienungsanleitung

Morphy Richards

Morphy Richards Bagged cylinder Vacuum Bedienungsanleitung

Morphy Richards

Morphy Richards VC7341DMUK Bedienungsanleitung

Morphy Richards

Morphy Richards IB73105 Bedienungsanleitung

Morphy Richards

Morphy Richards VC73215 MUK Bedienungsanleitung

Morphy Richards

Morphy Richards Pod vacuum cleaner Bedienungsanleitung

Morphy Richards

Morphy Richards Essentials Family and Pets+ Bedienungsanleitung

Morphy Richards

Morphy Richards Boxer wet & dry vacuum cleaner Bedienungsanleitung

Morphy Richards

Morphy Richards Scoot bagless vacuum cleaner Bedienungsanleitung

Morphy Richards

Morphy Richards ESSENTIAL MINI VACUUM CLEANER - REV 1 Bedienungsanleitung

Morphy Richards

Morphy Richards VORTICITY Bedienungsanleitung

Morphy Richards

Morphy Richards ESSENTIALS CYLINDER VACUUM CLEANER - REV 3 Bedienungsanleitung

Morphy Richards

Morphy Richards IB70313 Bedienungsanleitung

Morphy Richards

Morphy Richards VORTICITY Bedienungsanleitung

Morphy Richards

Morphy Richards Supervac Sleek Pro Bedienungsanleitung

Morphy Richards

Morphy Richards IB70240 Bedienungsanleitung

Morphy Richards

Morphy Richards PerformAir Upright Vacuum Bedienungsanleitung

Morphy Richards

Morphy Richards Ecolectric 73383 Bedienungsanleitung

Morphy Richards

Morphy Richards BAGLESS CYLINDER VACUUM CLEANER - REV 2 Bedienungsanleitung

Morphy Richards

Morphy Richards ESSENTIALS CYCLONIC BAGLESS UPRIGHT VACUUM CLEANER - REV... Bedienungsanleitung

Morphy Richards

Morphy Richards 73270 Bedienungsanleitung

Morphy Richards

Morphy Richards 732000 Supervac Bedienungsanleitung

Morphy Richards

Morphy Richards 732000 Supervac Bedienungsanleitung

Morphy Richards

Morphy Richards GOBLIN 1400W WET AND DRY CLEANER Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch

Morphy Richards CYCLONIC BAGLESS VACUUM CLEANER - REV 4 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken