Morphy Richards ESSENTIALS CYCLONIC BAGLESS UPRIGHT VACUUM CLEANER

wwwwww..mmoorrpphhyyrriicchhaarrddss..ccoomm

Essentials cyclonic bagless

upright vacuum cleaner

Please read and keep these instructions

Getting the best from your new cleaner...

If your cleaner is not picking up as well as it should, please check

Dust canister

It is important to regularly empty the canister, even if it does not appear full.

Filters

It is important that the pleated filter is shaken clean each time the dust canister is

emptied, this allows air through the appliance. Wash the canister filters regularly in

warm water and allow to air dry.

Blockages

Check the hose, tubes and tools for blockages.

Safety cut-out

If the air-flow is blocked or the filters are not regularly cleaned, a thermostat may

operate. If this happens, switch off and disconnect from the mains supply. Clear any

blockage, empty and clean the filters. Allow 60 minutes for the thermostat to reset.

Belt

Check and replace damaged or broken belt.

Height adjustment

The height adjustment only comes into effect when the handle is released by the

handle release pedal È.

VC73332 MUK Rev 1

For replacement parts, help with using your Morphy Richards, problems

and lots more, contact us by phone or through our website.

UUKKHHeellpplliinnee::0088445500777777770000

IIrreellaanndd11880000440099111199

73332 rev1 17/10/07 10:40 Page 1

IMPORTANT

SAFETY

INSTRUCTIONS

The use of any electrical

appliance requires the

following common sense

safety rules.

Primarily there is danger of

injury or death and secondly

the danger of damage to the

appliance. These are

indicated in the text by the

following two conventions:

WARNING: Danger to the

person!

IMPORTANT: Damage to the

appliance!

In addition we offer the

following safety advice.

Location

• Do not use or keep this

product outside.

• Do not store the appliance

near hot surfaces eg. ovens

or heating appliances.

Mains lead

• Do not allow the mains lead

to become strained or run

this appliance over it.

• If the electrical cable

becomes damaged, the

cable assembly must be

replaced. Do not attempt this

task yourself, contact the

helpline number that is found

at the bottom of the page.

Personal safety

• WARNING: Keep loose

clothing, hair, fingers etc.

away from the floor

nozzle whenever the

cleaner is connected to

the mains.

• WARNING: Only lift the

product by the handles

‡and ‰.

• Disconnect from the

mains supply before

attempting to clear

blockages, clear the

brush or replace the belt.

• Disconnect from the mains

supply before cleaning or

emptying the appliance.

• Never modify the cleaner in

any way.

• Never use in the presence of

explosive liquid or vapours.

• Never pick up inflammable or

poisonous liquids such as

petrol, copier toner or other

volatile substances. Never

pick up acids, asbestos or

asbestos dust.

• Never touch the plug or

cable with wet hands.

• Unprofessional repairs can

be dangerous for users.

• Use only Morphy Richards

spare parts and accessories.

• The appliance must never be

left running unsupervised.

• This appliance is intended for

domestic use only. Misuse or

use for commercial or any

other purpose will render the

guarantee invalid.

• Always disconnect the

appliance from the mains

supply after use.

• This appliance is not

intended for use by persons

(including children) with

reduced physical, sensory or

mental capabilities, or lack of

experience and knowledge,

unless they have been given

supervision or instruction

concerning use of the

appliance by a person

responsible for their safety.

• To protect against fire,

electric shock and personal

injury, do not immerse cord,

plug or cleaner in water or

other liquid.

Product safety

• Never use the appliance

without the filters being

installed.

• Never use the appliance to

vacuum hot ashes, broken

glass, sharp objects or

liquids.

• Never over-extend the hose

such that the cleaner is

pulled over. If the cleaner is

knocked over, switch off

before attempting to upright.

• Never pick the cleaner up by

the floor nozzle when

connected to the mains, use

the carrying handle.

Children

• Children do not understand

the dangers associated with

operating electrical

appliances. Never allow

children to use this

appliance.

• Children should be

supervised to ensure that

they do not play with the

appliance, or stumble over

the power cord.

Electrical

requirements

Check that the voltage on the

rating plate of your appliance

corresponds with your house

electricity supply which must

be A.C. (Alternating current).

If the socket outlets in your

home are not suitable for the

plug supplied with this

appliance, the plug should

be removed and the

appropriate one fitted.

WARNING: The plug

removed from the mains

lead, if severed, must be

destroyed, as a plug with

a bared flexible cord is

hazardous if engaged

into a live socket outlet.

Should the fuse in the 13

amp plug require changing, a

13 amp BS1362 fuse must

be fitted.

FFoorrAAddvviiccee,,SSppaarreessoorrAAcccceessssoorriieess,,tteell::0088445500777777770000((UUKK))oorr11880000440099111199((IIrreellaanndd))

73332 rev1 17/10/07 10:40 Page 2

⁄

‹

›

ﬂ

‡

‚



wwwwww..mmoorrpphhyyrriicchhaarrddss..ccoomm

„

ﬁ

‰

◊

FEATURES

⁄Eco Switch

(certain models only)

¤Front cover release

‹Removable front cover

›Exhaust filter grille

ﬁCarpet height adjustment

knob

ﬂFloor nozzle with powered

brush

‡Upper handle

·Flexible hose

‚Cord storage with quick

release cleat

„On/Off switch

‰Carrying handle

ÂNested extension tubes (x2)

ÊCrevice nozzle

ÁFurniture brush

ËHose clip slot

ÈHandle release pedal

ÍHose connector

ÎDust canister release

(shown page 5)

ÏDust canister lid

ÌPleated circular filter

ÓDust canister

ÔCentral mesh filter

Canister handle

ÒMotor protection filter

(shown page 6)

ÚExhaust filter

(shown page 6)

ÛBelt cover (shown page 7)

ÙBrush bar (shown page 7)

ıMotor shaft (shown page 7)

ˆBrush bar end caps

(shown page 7)

˜Hose clip

¯Turbo nozzle

(certain models only)

˘Belt guard (shown page 7)

◊& Hair and stair tool

(certain models only)

73332 rev1 17/10/07 10:40 Page 3

OPERATING THE

APPLIANCE

Assembly A

WARNING: Do not plug in

the cleaner until it is

assembled.

1Carefully unpack all of the

components.

2Lift the cleaner body to the

upright position.

3Remove the two screws that are

already attached to the body.

4From the rear of the cleaner,

align the handle with the groove

and slide into the body. If

necessary, use thumb and finger

pressure to slide the handle into

position.

5Fasten the handle with the two

screws.

Floor nozzle

height adjustment B

Before using the cleaner, the

floor nozzle height must be set

to the correct height.

Choose the setting which most

closely matches your floor

surface.

• Use the TOOLS setting when

using the tools.

Note: The height adjustment

only comes into effect when the

handle is released by the handle

release pedal È.

Eco Switch C

(Certain models only)

The Eco Switch ⁄ allows you

to turn down the power when

cleaning more delicate items,

such as curtains and upholstery,

saving energy and reducing

costs.

Using on carpets

1Place the cleaner in it’s upright

position.

2Set the carpet height

adjustment knob to the desired

position.

3Release the mains cable by

revolving the quick release cleat

half-a-turn and extend the cable

fully.

4Plug the cable into the mains

socket.

5Step on the handle release

pedal to release the handle to

the desired position.

6Press the on/off button to the

‘on’ position.

IMPORTANT: To prevent damage

to carpets, never leave the

cleaner switched on in one

place for an extended period.

• Never have the brushes set too

low such that the cleaner is hard

to push.

FFoorrAAddvviiccee,,SSppaarreessoorrAAcccceessssoorriieess,,tteell::0088445500777777770000((UUKK))oorr11880000440099111199((IIrreellaanndd))

73332 rev1 17/10/07 10:40 Page 4

wwwwww..mmoorrpphhyyrriicchhaarrddss..ccoomm

Using the

attachments

Follow steps 1-4but set the

carpet height adjustment knob

to the TOOLS setting.

5Remove the hose connector Í

from the rear of the cleaner. Lift

the hose ·from the top handle

hook. Insert the hose clip ˜

into the hose clip slot Ë.

• Push the required attachment

firmly onto the end of the hose.

• If additional length is required,

attach one or both extension

tubes.

6Switch on/off.

• IMPORTANT: Always fix the

hose clip ˜to the main body

slot Ëwhen using the hose and

tools.

• Never over extend the hose

such that the cleaner is pulled

over.

IMPORTANT: Turning the cleaner

sideways helps prevent the

cleaner being pulled along by

the stretch hose.

Using & cleaning the

turbo nozzle

(Certain models only)

Attach the turbo nozzle to the

hose end connector Í.

Following use, your turbo nozzle

may become clogged. Turn over

the nozzle and pull away any

hairs or fibres. If they are tightly

wound around the brush,

carefully snip the fibres with

scissors, being careful not to

damage the brush bar, pull away

from the brush bar and dispose.

Using the Hair and

stair tool

(Certain models only)

Attach the stair tool ◊to the

hose connector Ífor effective

stair cleaning.

Attach the hair tool to the

stair tool for fantastic pet hair

pick-up D.

EMPTYING

Empty the dust canister

regularly even if it does not look

full, this will maintain the

performance.

1Remove the front cover by lifting

the cover release lever ¤ E.

2Lift-up the dust canister release

Îand pull the canister away

from the main body.

3Take the canister to the dustbin.

4Turn the lid quarter-of-a-turn

anti-clockwise to unlock, lift off

the lid with pleated filter Ì, put

to one side F.

5Lift out the central mesh filter Ô

from the dust canister Ó G.

Brush clean if necessary.

6Empty out the dust canister Ó.

7Re-fit the central mesh filter.

8Shake the pleated filter to

remove all dust.

9Re-fit pleated filter with lid into

the dust canister by lining up the

two arrows and turning the lid

quarter-of-a-turn clockwise to

lock.

10 Re-fit dust canister into cleaner

and push to lock into position.

11 Re-fit the front cover.

◊

73332 rev1 17/10/07 10:40 Page 5

SAFETY CUT-OUT

If the cleaner overheats, a

motor protection thermostat will

automatically switch the motor

off. If this happens, switch the

cleaner off, unplug from the

power supply and leave the

cleaner to cool for at least

60 minutes. Check the

airways for blockages, empty

the dust canister and clean the

filters before restarting.

CLEANING THE

FILTERS

To maintain suction, the

pleated filter must be

shaken clean each time the

dust canister is emptied.

Failure to clean the filter will

reduce suction and could

damage the motor if used for a

prolonged period. This may

invalidate the guarantee. If the

filters become damaged, they

must be replaced.

Pleated filter

This must be shaken clean at

every emptying to maintain

suction. To thoroughly clean it,

wash it regularly.

To remove it from the dust

canister lid, turn the filter

quarter-of-a-turn anti-clockwise

H. Wash in warm water (no

detergent) and allow to air dry

before refitting.

Motor protection filter

The motor protection filter Òis

located underneath the dust

canister.

1Remove the dust canister.

2Lift out the filter and shake over

a dustbin.

The filter may also be washed in

water (no detergents). Allow the

filter to air dry. Ensure the filter

is thoroughly dry before refitting.

3Replace the filter.

Exhaust filter J

The exhaust filter is located

below the dust canister

compartment.

1Remove the front cover.

2Remove the exhaust filter Úby

pulling forward at the top and

lifting it away.

3Take the filter out of the cage

and shake vigorously over a

dustbin. The filter may also be

washed in warm water. Do not

use detergents. The filter must

be completely dry before re-

fitting. Allow filters to air dry

naturally.

4Replace the filter and the front

cover.

Changing the belt

If the brush bar stops rotating, it

is likely that the drive belt has

snapped (usually because the

brush has been stalled). A spare

belt is supplied. Replacement

belts can also be obtained from

Morphy Richards by calling the

helpline number at the base of

the page.

Accessing the floor

nozzle K

1Disconnect the cleaner from the

mains supply.

2Put the switch to the ‘off’

position.

3Remove the front cover and the

dust canister.

4Press the handle release pedal

and place the cleaner face

down, in a flat position on a soft

surface (eg. carpet).

5Using a flat bladed screwdriver

or a coin, rotate the three cover

fixings, a quarter-of-a-turn, from

lock to unlock K.

6Lift the base cover, from the rear

fixing area first, the cover will

rotate forward. Unhook the

cover from the front edge and

remove.

FFoorrAAddvviiccee,,SSppaarreessoorrAAcccceessssoorriieess,,tteell::0088445500777777770000((UUKK))oorr11880000440099111199((IIrreellaanndd))

73332 rev1 17/10/07 10:40 Page 6

wwwwww..mmoorrpphhyyrriicchhaarrddss..ccoomm

Removing rotating

brush & belt L,M

7Lift the metal belt guard ˘out

of the floor nozzle and put it

safely to one side L.

8Slide the belt past the end of the

motor drive shaft. If the belt has

broken, remove all pieces and

clean the drive shaft.

9Lift the rotating brush equally at

both ends to slide it free of the

floor nozzle M. Holding the

ends of the brush, check it

rotates freely or not, if not, it

must be replaced. Call our

Helpline for replacement parts

or belts.

Re-fitting rotating

brush & belt N

10 Hook the belt over the the drive

shaft (the belt must be slid

sideways past the end of the

drive shaft). Note: The belt guard

must have been removed first,

see point 7 above.

11 Refit the belt guard, ensuring it

is correctly located. Press down

fully.

12 Pass the rotary brush through

the belt, ensuring the correct

end is located against the belt

13 Pull the brush forward (against

the pull of the belt) and locate

the square ends of the brush

into location slots in the floor

nozzle N.

14 Rotate the brush by hand to

ensure the belt is running in the

centre of it’s location on the

brush.

Refitting the floor

nozzle base cover O

15 Hook the base cover into the

front of the floor nozzle,

ensuring all four hooks are

engaged O.

16 Rotating the cover downwards

and rearwards, slowly close the

cover.

17 Tighten the three fixings, using a

screwdriver to turn the fixings a

quarter-of-a-turn to the lock

position.

Note: If the cover will not fully

close or fixings will not lock, lift

the cover slightly and rotate the

fixings until they are in the

correct position for closure.

18 Return the cleaner to the upright

position, re-fit the dust canister

and front cover. Connect to the

mains supply. Switch on to test.

HELPLINE

If you have any difficulty with

your appliance, do not hesitate

to call us.

We are more likely to be able

to help than the store from

where you bought it.

Please have the following

information ready to enable our

staff to deal with your query

quickly.

• Name of the product

• Model number as shown on the

underside of the appliance.

• Serial number as shown on

underside of the appliance.

UK Helpline 0845 077 7700

Ireland Helpline 1800 409 119

73332 rev1 17/10/07 10:40 Page 7

Morphy Richards products are intended for household use only.

Morphy Richards has a policy of continuous improvement in product quality and

design. The company therefore reserves the right to change the specification of

its models at any time.

The After Sales Division

Morphy Richards Ltd

Mexborough, SouthYorkshire,

England, S64 8AJ

Helpline (office hours)

UK 0845 077 7700

Republic of Ireland 1800 409 119

VC73332 MUK Rev 1 09/07

FFoorrddeettaaiillssooffootthheerrpprroodduuccttssiinntthheeMMoorrpphhyyRRiicchhaarrddssrraannggeepplleeaasseesseeeeoouurrwweebbssiittee......

wwwwww..mmoorrpphhyyrriicchhaarrddss..ccoomm

YOUR TWO YEAR

GUARANTEE

It is important to retain the

retailer’s receipt as proof of

purchase. Staple your

receipt to this back cover

for future reference.

Please quote the following

information if the product

develops a fault. These

numbers can be found on

the base of the product.

Model no.

Serial no.

All Morphy Richards

products are individually

tested before leaving the

factory. In the unlikely event

of any appliance proving to

be faulty within 28 days of

purchase, it should be

returned to the place of

purchase for it to be

replaced.

If the fault develops after

28 days and within 24

months of original

purchase, you should

contact the helpline

number quoting model

number and serial number

on the product, or write to

Morphy Richards at the

address shown.You will be

asked to return the product

(in secure, adequate

packaging) along with a

copy of proof of purchase.

Subject to the exclusions

set out below (1-6), the

faulty appliance will then

be repaired or replaced

and dispatched usually

within seven working days

of receipt.

If for any reason this item is

replaced during the 2-year

guarantee period, the

guarantee on the new item

will be calculated from

original purchase date.

Therefore it is vital to retain

your original receipt or

invoice to indicate the date

of initial purchase.

To qualify for the two-year

guarantee, the appliance

must have been used

according to the

manufacturer’s

instructions. For example,

the filters must have been

regularly cleaned as

instructed.

Morphy Richards shall not

be liable to replace or

repair the goods under the

terms of the Guarantee

where:

EXCLUSIONS

1The fault has been caused

or is attributable to

accidental use, mis-use,

negligent use or used

contrary to the

manufacturer’s

recommendations or where

the fault has been caused

by power surges or

damage caused in transit.

2The appliance has been

used on a voltage supply

other than that stamped on

the products.

3Repairs have been

attempted by persons

other than our service staff

(or authorised dealer).

4Where the appliance has

been used for hire

purposes or non-domestic

use.

5Morphy Richards are not

liable to carry out any type

of servicing work under the

guarantee.

6Consumables such as the

filters and belt are not

covered by the guarantee.

• This guarantee does not

confer any rights other than

those expressly set out

above and does not cover

any claims for

consequential loss or

damage. This guarantee is

offered as an additional

benefit and does not affect

your statutory rights as a

consumer.

• This guarantee is valid in

the UK and Ireland only.

For electrical products sold within the

European Community. At the end of the

electrical products useful life it should

not be disposed of with household

waste.

Please recycle where facilities exist.

Check with your Local Authority or

retailer for recycling advice in your

country.

73332 rev1 17/10/07 10:40 Page 8

Inhaltsverzeichnis

Andere Morphy Richards Staubsauger Handbücher

Morphy Richards

Morphy Richards Storm Bedienungsanleitung

Morphy Richards

Morphy Richards IB73190 Bedienungsanleitung

Morphy Richards

Morphy Richards VC73410 MUK Bedienungsanleitung

Morphy Richards

Morphy Richards IB73120 Bedienungsanleitung

Morphy Richards

Morphy Richards Ultralight vacuum cleaner Bedienungsanleitung

Morphy Richards

Morphy Richards IB71051 Bedienungsanleitung

Morphy Richards

Morphy Richards Bagless Cylinder Vacuum Cleaner Bedienungsanleitung

Morphy Richards

Morphy Richards Supervac Deluxe Bedienungsanleitung

Morphy Richards

Morphy Richards VC73240MUK Bedienungsanleitung

Morphy Richards

Morphy Richards IB73100 Bedienungsanleitung

Morphy Richards

Morphy Richards IB70191 Bedienungsanleitung

Morphy Richards

Morphy Richards IB70041 Bedienungsanleitung

Morphy Richards

Morphy Richards PremAir Cyclonic 70035 Bedienungsanleitung

Morphy Richards

Morphy Richards ORB PETS CYCLONE VACUUM CLEANER - REV 1 Bedienungsanleitung

Morphy Richards

Morphy Richards SpillMaster Bedienungsanleitung

Morphy Richards

Morphy Richards IB71053 Bedienungsanleitung

Morphy Richards

Morphy Richards VORTICITY Bedienungsanleitung

Morphy Richards

Morphy Richards VC73270MUK Bedienungsanleitung

Morphy Richards

Morphy Richards IB70061 Bedienungsanleitung

Morphy Richards

Morphy Richards 73199 Bedienungsanleitung

Morphy Richards

Morphy Richards 71077 VACUUM CLEANER Bedienungsanleitung

Morphy Richards

Morphy Richards Supervac Deluxe Bedienungsanleitung

Morphy Richards

Morphy Richards 73285 BAGLESS UPRIGHT VACUUM CLEANER Bedienungsanleitung

Morphy Richards

Morphy Richards PerformAir Upright Vacuum Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch

Morphy Richards ESSENTIALS CYCLONIC BAGLESS UPRIGHT VACUUM CLEANER - REV... Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken