Moxa Technologies IoLogik E1200 Series Bedienungsanleitung

P/N: 1802012001014

*1802012001014*

ioLogik E1200 Series

Quick Installation Guide

Edition 5.0, September 2016

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

The ioLogik E1200 series comes with 2 embedded Ethernet switch ports

that can form a daisy-chain topology, which is the easiest way to add

more Ethernet devices to a network or connect your ioLogiks in series.

Moxa’s free Active OPC Server offers active (or “push”) communication

that works between Moxa’s ioLogik units and HMI/SCADA systems,

providing instant I/O status reports by “Active Tags.” The event-driven

active tags result in an I/O response time that is faster than other OPC

Server packages.

Model Selection:

ioLogik

DIO

Relay

RTD

E1210

E1211

E1212

E1213*

E1214

E1240

E1241

E1242

E1260

E1262

*The ioLogik E1213 has source DOs.

Package Checklist

•1 ioLogik E1200 series remote I/O product

•Quick installation guide (printed)

Specifications

System

Ethernet

2 x 10/100 Mbps switch ports, RJ45

Protection

1.5 KV magnetic isolation

Protocols

Modbus/TCP, TCP/IP, UDP, DHCP, Bootp, HTTP

Power Input

24 VDC nominal, 12 to 36 VDC

Wiring

I/O cable max. 14 AWG

Dimensions

27.8 x 124 x 84 mm (1.09 x 4.88 x 3.31 in)

Weight

under 200 g

Operating Temperature

Standard Models:

-10 to 60°C (14 to 140°F)

Wide Temp. Models:

-40 to 75°C (-40 to 167°F)

Storage Temperature

-40 to 85°C (-40 to 185°F)

Ambient Relative

Humidity

5 to 95% (non-condensing)

Altitude

Up to 2000 m

Note: Contact Moxa if you require products guaranteed to function

properly at higher altitudes.

Standards and

Certifications

UL 508, CE, FCC Class A

Warranty Period

5 years (excluding ioLogik E1214*)

Details

See www.moxa.com/warranty

*Because of the limited lifetime of power relay, products that use this

component are covered by a 2-year warranty.

- 3 -

Digital Input

Sensor Type

NPN, PNP, and Dry contact

I/O Mode

DI or Event Counter

Dry Contact

• On: short to GND

• Off: open

Wet Contact (DI to COM)

• On: 10 to 30 VDC

• Off: 0 to 3 VDC

Isolation:

3K VDC or 2K Vrms

Counter/Frequency:

250 Hz, power off storage

Digital Output (Sink)

I/O Mode

DO or Pulse Output

Pulse Wave

Width/Frequency

1 ms/500 Hz

Over-voltage Protection

45 VDC

Over-current Protection

2.6 A (4 channels @650 mA)

Over-temperature

Shutdown

175°C (typical), 150°C (min.)

Current Rating

200 mA per channel

Isolation

3K VDC or 2K Vrms

Digital Output (Source)

I/O Mode

DO or Pulse Output

I/O Type

Source

Current

0.5A per channel

Voltage

For DIO channel:

15 to 30 VDC (ext power voltage)

For DO channel:

15 to 30 VDC (ext

power voltage), 12 or 9 VDC

configurable by jumper.

Pulse Wave

Width/Frequency

1 ms/500 Hz

Over-voltage Protection

41 VDC

Over-current Limit

6 A

Over-temperature

Shutdown

175°C (typical), 150°C (min.)

Output Current Rating

1.5 A per channel

Relay Output

Type

Form A (N.O.) relay outputs, 5A

Contact Rating

5 A @ 30 VDC, 5 A @ 250 VAC, 5 A @ 110 VAC

Inductance Load

2 A

Resistance Load

5 A

Breakdown Voltage

500 VAC

Relay On/Off Time

1500 ms (max.)

Initial Insulation

Resistance

1G min. @ 500 VDC

Expected Life

100,000 times (typical)

Initial Contact Resistance

30 milli-ohms (max.)

Pulse Output

0.3 Hz at rated load

Analog Input

Type

Differential input

Resolution

16 bits

I/O Mode

Voltage / Current

Input Range

0 to 10 VDC, 4 to 20 mA

- 4 -

Accuracy

±0.1% FSR @ 25°C

±0.3% FSR @ -10 and 60°C

±0.5% FSR @ -40 and 75°C

Sampling Rate (all

channels)

12 samples/second

Input Impedance

10M ohms (min.)

Built-in Resistor for

Current Input

120 ohms

Analog Output

Resolution

12 bits

Output Range

0 to 10 VDC, 4 to 20 mA

Voltage Output

10 mA (max.)

Accuracy

±0.1% FSR @ 25°C

±0.3% FSR @ -40 and 75°C

Load Resistor

Internal register: 400 ohms

Note: 24 V of external power is required when loading > 1000 ohms.

RTD

Input Type

PT50, PT100, PT200, PT500, PT1000

Resistance

1–310, 1–620, 1–1250, 1–2200 ohms

Sampling Rate

12 samples/sec (all channels)

Resolution

16 bits

Accuracy

±0.1% FSR @ 25°C

±0.3% FSR @ -40 and 75°C

Input Impedance

625k ohms

Thermocouple Input

Sensor Type

J, K, T, E, R, S, B, N

Millivolt Type

±78.126 mV, ±39.062 mV, ±19.532 mV

Fault and Overvoltage

protection

±35 VDC (power off); +30 VDC, -25 VDC

(power on)

Sampling Rate

12 samples/sec (all channels)

Resolution

16 bits

Accuracy

±0.1% FSR @ 25°C

±0.3% FSR @ -40 and 75°C

Input Impedance

10M ohms

Installation

Connecting the Power

Connect the +12 to +36 VDC power line to the ioLogik E1200’s terminal

block V+ terminal; connect the ground from the power supply to the V-

terminal. Connect the ground pin ( ) if earth ground is available.

NOTE

For safety reasons, wires connecting the power supply should be

at least 2 mm in diameter (e.g., 12 gauge wires).

- 5 -

Jumper Settings

Models with DIO, AI, or external power channels require configuring the

jumpers inside the enclosure. Remove the screw located on the back

panel and open the cover to configure the jumpers.

DIO mode configurations are

shown above (Default: DO Mode).

Analog mode configurations are

shown above (Default: Voltage

Mode).

DOs on the ioLogik E1213 have 3

possible external (EXT) power

configurations, which are shown to

the right. Only one field power can

be selected at a time (JP10 / 12V JP5

/ 9V JP11)

and

the jumper must be

inserted vertically, not horizontally

(Default: Field Power JP10).

NOTE

The ioLogik E1213 has 4 pure DO channels and 4 hybrid DIO

channels. For the 4 pure DO channels, you can use the jumpers to

select the power configuration output (i.e., field power, 12 V, 9

V). But for the 4 hybrid DIO channels, you cannot use the

umpers to select the power configuration output. Instead, you

can only use the jumpers to set the DIO channels to either DI

mode or DO mode.

Mounting

There are two sliders on the back of the unit for DIN rail and wall

mounting.

1. Mounting on a DIN rail: Pull out the bottom slider; latch the unit

onto the DIN-rail, and push the slider back in.

2. Mounting on the wall: Pull out both the top and bottom sliders and

align the screws accordingly.

Connecting to the Network

The ioLogik E1200 has two built-in RJ45 Ethernet ports for connecting

standard direct or cross-over Ethernet cables.

- 6 -

LED Indicators

Type

Color

Description

Power

Amber

System power is ON

Off

System power is OFF

Ready

Green

System is ready

Flashing

Flashes every 1 sec when the “Locate”

function is triggered

Flashing

Flashes every 0.5 sec when the firmware is

being upgraded

Flashing

An on/off period cycle: 0.5 second shows

“Safe Mode”

Off

System is not ready.

Port 1

Green

Ethernet connection enabled

Flashing

Transmitting or receiving data

Port 2

Green

Ethernet connection enabled

Flashing

Transmitting or receiving data

EXT

(E1213 only)

Green

EXT field power input is connected

Off

EXT field power input is disconnected

I/O Wiring

Digital Inputs/Outputs

Analog Inputs/Outputs

- 7 -

Relay Output (Form A)

RTD Inputs

TC Inputs

System Configuration

Configuration via Web Console

Main configuration of an ioLogik E1200 is by web console.

•Default IP Address: 192.168.127.254

•Subnet Mask: 255.255.255.0

NOTE

Be sure to configure the host PC’s IP address to the same subnet

as the ioLogik E1200. For example, 192.168.127.253

ioSearch Utility

ioSearch is a search utility that helps users locate an ioLogik E1200 on the

local network. The utility can be downloaded from Moxa’s website.

- 8 -

Load Factory Default Settings

There are three ways to restore the ioLogik E1200 to factory default

settings.

1. Hold the RESET button for 5 seconds.

2. In the ioSearch utility, right-click on the ioLogik device to be reset and

select Reset to Default.

3. Select Load Factory Default from the web console.

Modbus Address Table

Consult the user’s manual for the ioLogik’s Modbus address, or find the

default address of the I/O channels in the web console by clicking

User-defined Modbus Addressing Default Address.

Active OPC Server Connection

Connect the ioLogik E1200 to an Active OPC Server by following the steps

below:

1. Disable the user-defined Modbus address function.

2. Download Active OPC Server Lite utility from Moxa's website and

install it.

3. Install from Web console Active OPC Server Settings AOPC

& I/O Settings; specify the IP address where the Active OPC Server

is installed. Specify the I/O channels that need to be added to Active

OPC Server Lite. Submit the settings and then Save/Restart.

4. From Web Console Active OPC Server Settings Create

AOPC Tag, click the Create Tag button.

5. Launch Active OPC Server Lite from the Windows Start menu: Start

Programs MOXA IOServer ActiveOPC ActiveOPC.

Save configurations before exiting Active OPC Server Lite.

NOTE

A “load” in a circuit schematic is a component or portion of the

circuit that consumes electric power. For the diagrams shown in

this document, “load” refers to the devices or systems connected

to the remote I/O unit.

ATEX Information

1. Certificate number: DEMKO 13 ATEX 1210600X

2. Certification string: Ex nA nC IIC T3 Gc

3. Standards covered:

EN 60079-0:2012+A11:2013, EN 60079-15:2010

4. These products are to be installed in an ATEX Certified IP54

enclosure and accessible only by the use of a tool.

5. These products are for use in an area of not more than pollution

degree 2 in accordance with IEC 60664-1.

Andere Handbücher für ioLogik E1200 Series

Inhaltsverzeichnis

Andere Moxa Technologies Netzwerk-Router Handbücher

Moxa Technologies

Moxa Technologies EDS-505A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies OnCell 5004 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NAT-102 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort IA5150 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-G205A-4PoE Handbuch

Moxa Technologies

Moxa Technologies OnCell G4302-LTE4 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PowerTrans PT-7728 Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDR-G902 Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Handbuch

Moxa Technologies

Moxa Technologies SDS-3008 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TN-5916 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-508 Handbuch

Moxa Technologies

Moxa Technologies MAR-2000 Bedienungsanleitung

Moxa Technologies

Moxa Technologies SR3000 Bedienungsanleitung

Moxa Technologies

Moxa Technologies Managed Ethernet Switch/Extender Bedienungsanleitung

Moxa Technologies

Moxa Technologies WDR-3124A Bedienungsanleitung

Moxa Technologies

Moxa Technologies TN-4900 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ioLogik E2200Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-405 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UC-8112-LX-STK Bedienungsanleitung

Moxa Technologies

Moxa Technologies OnCell 5004-HSPA Bedienungsanleitung

Moxa Technologies

Moxa Technologies ioLogik E1242 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

Moxa Technologies ioLogik E1200 Series Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken