– 1 – – 2 – – 3 – - 4 -
P/N: 1802050040012
OnCell 5004/5104 Series
Quick Installation Guide
Third Edition, December 2011
Overview
The OnCell 5004/5104 series are high-performance industrial grade
cellular routers that allow up to 4 Ethernet-based devices to
simultaneously use a single cellular data account for primary or
backup network connectivity to remote sites and devices. Both
products provide the functionality of a cellular router, firewall, and
switch in one single device. The difference between the OnCell 5004
and the 5104 series is that the OnCell 5104 comes with a built-in
relay output that can be configured to indicate the priority of events
to notify and warn engineers in the field, and the two digital inputs
allow you to connect basic I/O devices, such as sensors, to the
cellular router. In addition, the OnCell 5104 has an IA design and can
be attached to a DIN-rail, whereas the OnCell 5004 can be placed on
a desktop or be wall-mounted. Both products use 12 to 48 VDC
power inputs with a screw-on connector for greater reliability, and
the Ethernet port comes with 1.5 KV magnetic isolation protection to
keep your system safe from unexpected electrical discharges.
Package Checklist
Before Installing the OnCell 5004/5104 series Cellular Router, verify
that the package contains the following items:
Standard Accessories
•Rubber SMA antenna
•Rubber stand (OnCell 5004 series only)
•Wallmount Kit (OnCell 5004 series only)
•Din-Rail Kit (OnCell 5104 series only)
•Terminal block (screw type)
•Document and Software CD
•Product warranty statement
•Quick Installation Guide
Note: Please notify your sales representative if any of the above
items are missing or damaged.
Hardware Introduction
OnCell 5004 series
OnCell 5104 series
Reset Button
Press the Reset Button continuously for 5 sec to load factory default
settings. Use a pointed object, such as a straightened paper clip or
toothpick, to press the reset button. This will cause the Ready LED to
blink on and off. The factory default settings will be loaded once the
Ready LED stops blinking (default LAN IP: 192.168.127.254).
LED Indicators
The following table explains the LED indicators on the front panel of
the OnCell 5004/5104 series:
Power is off, or power error
Power is off, or power error
condition exists.
GPRS/EDGE is disconnected
UMTS/HSDPA/HSPA is connected
UMTS/HSDPA/HSPA is
disconnected
Steady on: SIM 1 is activated
Blinking: SIM 1 not inserted
Steady on: SIM 2 is activated
Blinking: SIM 2 not inserted
Steady on: Software Ready.
Blinking slowly (1 sec): The OnCell
has been located by the OnCell
Search Utility.
Power is off, or is booting up.
Steady on: Booting up, or IP fault.
Blinking slowly (1 sec): Cannot get
an IP address from the DHCP server
Power is off, or there is no error
Steady on: Software Ready.
Blinking slowly (1 sec): Data
Power is off, or is booting up.
Signal Level (at least 2 LEDs must
illuminated for data Transmission)
Connecting the I/O Port
The OnCell 5104/5104 series has six terminals on the terminal block
for the I/O ports, with 4 terminals used for input, and 2 terminals
used for output.
Digital Input—The power input level determines the digital input’s
ON/OFF state:
On: +13 to +30 V for state “1”
Off: -30 to +3 V for state “0”
Digital Output—1 relay output with current carrying capacity of 1 A
@ 24 VDC.
Hardware Installation Procedure
STEP 1: Open the SIM cover, and insert the SIM card into the SIM
card slot.
STEP 2: Connect the 12-48 VDC power adaptor to the OnCell
5004/5104 series and then plug the power adaptor into a DC outlet.
STEP 3: To configure the OnCell, use an Ethernet cable to connect
the OnCell’s LAN port directly to your computer’s Ethernet interface.
STEP 4: Connect the OnCell 5004/5104 series’ Ethernet port to an
Ethernet enabled device.
Software Installation Information
The Document & Software CD contains the User’s Manual, and the
OnCell Search Utility. Insert the CD and follow the on-screen
instructions. Please refer to the User’s Manual for additional details
on using the OnCell Search Utility.
Pin Assignments and Cable Wiring
Ethernet Port Pin Assignment
Note: Please read Chapter 2: Getting Started in the OnCell
5004/5104 User’s Manual for more details about installation and
configuration.
Power Input and Relay Output Pinouts
