Moxa Technologies OnCell G4302-LTE4 Series Bedienungsanleitung

P/N: 1802043020010

*1802043020010*

OnCell G4302-LTE4 Series

Quick Installation Guide

Moxa OnCell Series

Version 1.0, May 2023

Technical Support Contact Information

www.moxa.com/support



- 2 -

Overview

The OnCell G4302-LTE4 is a reliable, secure, LTE router with a state-

of-the-art LTE module. This 4G cellular router provides a highly reliable

connection to your Ethernet and serial network for cellular applications.

The OnCell G4302-LTE4 is ideal for remote-access applications where

power consumption needs to be well managed. The power-saving

functions help significantly reduce and manage the power consumption

of your cellular network. Security functions such as VPN, firewall, NAT,

and secure boot protect the internal network from unauthorized access,

DoS attacks, and tampering. Wide-temperature support coupled with

high levels of EMS protection provides the OnCell G4302-LTE4 with the

highest degree of device stability for any rugged environment. In

addition, dual-SIM and GuaranLink support help provide network

redundancy to ensure uninterrupted connectivity.

The OnCell G4302-LTE4 also comes with a 3-in-1 serial port for serial-

over-LTE cellular network communication, making it suitable for

collecting and exchanging data with serial/Ethernet devices.

Package Checklist

Before installing your OnCell G4302-LTE4, verify that the package

contains the following items. If any of these items is missing or

damaged, please contact your customer service representative for

assistance.

•1 OnCell G4302-LTE4 unit

•Quick installation guide (printed)

•Warranty card

Installation and Configuration

You will need access to a notebook computer or PC equipped with an

Ethernet port. The OnCell G4302-LTE4 has a default IP address that

you must use when connecting to the device for the first time.

Take the following steps to configure your OnCell G4302-LTE4. Refer to

the Panel Layout of the OnCell G4302-LTE4 section below for the

location of the ports and sockets.

STEP 1: Insert a SIM card and turn on the OnCell G4302-LTE4

1. Install a SIM card into the OnCell device. For details, refer to the

SIM Card Socket section.

2. Turn on the OnCell device by connecting a power terminal block to

either or both 12 to 48 VDC power inputs. For details, refer to the

Connecting the Power Input section.

STEP 2: Connect the OnCell G4302-LTE4 to a notebook or PC

Since the OnCell device supports MDI/MDI-X auto-sensing, you can use

either a straight-through or crossover cable to connect the OnCell

device to a computer. See the 10/100/1000BaseT(X) Ethernet Port

Connection section for detailed instructions. If the LAN LED indicator on

the OnCell device lights up, it means a connection has been

established.

STEP 3: Set up an IP address for the computer

Set an IP address on the same subnet as the OnCell device. Since the

OnCell device’s default IP address is 192.168.127.254, and the

- 3 -

subnet mask is 255.255.255.0, you should set the IP address of the

computer to 192.168.127.xxx and the subnet mask to

255.255.255.0.

STEP 4: Use the web-based manager to configure the OnCell

G4302-LTE4

Open your computer’s web browser and type

http://192.168.127.254 in the address field to access the homepage

of the web-based management system. Before the homepage opens,

you will need to enter the username and password. For first-time

configuration, enter the following default username and password:

Username: admin

Password: moxa

Click Login.

ATTENTION

For security reasons, we strongly recommend changing the

password. To

change the password, go to System



Account

Management 

User Accounts, and then follow the on-

screen instructions.

Panel Layout of the OnCell G4302-LTE4

Front Panel View

Back Panel View

Top Panel View

Bottom Panel View

- 4 -

1. Cellular antenna port (Main)

2. Cellular antenna port (AUX)

3. GNSS antenna port

4. 100/1000 Base-T(X) Ethernet LAN port 2 (RJ45)

5. 100/1000 Base-T(X) Ethernet LAN port 1/WAN port (RJ45)

6. USB port

7. Reset button

8. Console port (reserved for engineering use)

9. LED display

10. SIM card tray (SIM1/SIM2)

11. DIN-rail mounting kit

12. Grounding screw

13. Terminal block (PWR1, PWR2, DI, Relay)

14. DB9 serial port

- 5 -

Device Dimensions

DIN-rail Mounting

The OnCell G4302-LTE4 Series comes with a DIN-rail kit attached to the

back panel. Mount the OnCell G4302-LTE4 Series on corrosion-free

mounting rails that meet the EN 60715 standard.

- 6 -

Installation

STEP 1: Insert the upper lip of the

DIN rail into the top hook of the

DIN

-rail mounting kit.

STEP 2:

Press the OnCell G4302-

LTE4 Series towards the DIN rail

until it snaps into place.

Removal

STEP 1:

Pull down the latch on the

mounting kit with a screwdriver

STEP 2:

Slightly pull the device

forward

STEP

3: Lift up the device to

remove it from the DIN rail

Wall Mounting (optional)

NOTE

Mounting the OnCell G4302-LTE4 Series onto a wall requires

the WK-41-01 wall-mounting kit, which is sold separately.

For some applications, it may be more convenient to mount the OnCell

G4302-LTE4 to a wall, as illustrated below:

- 7 -

Installation

STEP 1: Attach the wall-mounting kit

to the OnCell device by i

nserting the

upper lip of the DIN

-rail kit into the

hook of the wall

mounting kit.

STEP 2

: Press the OnCell device

towards the wall mounting kit until it

snaps into place.

STEP 3:

Mounting the OnCell device to a wall requires 4

screws. Use the OnCell device with

the wall mount

kit

attached as a guide to mark the correct locations of

the 4 screws. The heads of the screws should be less

than 6.0 mm in diameter, and the shafts should b

less than 3.5 mm in diameter, as shown in the figure

at the right. The length of the screws should be at

least 10 mm.

NOTE

Test the screw head and shank size by inserting the screws into

one of the k

eyhole shaped apertures of the wall-mounting

plates before attaching the plates to the wall.

STEP

Once the screws are fixed into the wall, insert

the four screw heads through the large opening

of the keyhole

-shaped apertures of the

mounting kit, and then slide the OnCell device

downwards.

Tighten the four screws for added

stability.

- 8 -

Removal

STEP 1: Pull down the latch on the

mounting kit with a screwdriver

STEP 2:

Slightly pull the device

forward

STEP

3: Lift up the device to

detach it from the wall

WARNING

•

This equipment is intended to be used in a Restricted

Access Location, such as a dedicated computer room,

where access can only be gained by SERVICE PERSONS or

by USERS who have been instructed about the fact that the

metal chassis of the equipment is extremely hot and may

cause burns.

•

Service persons or users should pay special attention and

take special precautions before handling this equipment.

•

Only authorized, well-trained professionals should be

allowed to access the restricted access location. Access

should be controlled by the authority responsible for the

location with lock and key or a security identity system.

•

External Metal Parts are Hot!! Pay special attention or

use special protection before handling this equipment.

Wiring Requirements

WARNING

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring the OnCell device.

Read and Follow These Guidelines

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE

Do not run signal or communications wiring and power wiring in

the same wire conduit. To avoid

interference, wires with

different signal characteristics should be routed separately.

- 9 -

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb

is that wiring with similar electrical characteristics can be bundled

together.

•Keep input wiring and output wiring separate.

•It is strongly advised that you label wiring to all devices in the

system when necessary.

ATTENTION

This product is intended to be supplied by an external power

source (UL Listed/ IEC 60950

-1/ IEC 62368-1), of which the

output complies with ES1/SELV,

the output rating is 12 to 48

VDC, 0.96A min.,

supports an ambient temperature of 70°C

minimum for use wi

th OnCell G4302 Series -T models, or an

ambient temperature

of 55°C minimum for use with OnCell

G4302 Series non-T models.

Grounding the Moxa OnCell Series

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI) by routing the noise from the metal

chassis to the connected ground. Run the ground connection from the

ground screw to the grounding surface prior to connecting devices. The

minimum cross-sectional area of the grounding conductor should be

equal to that of the input cable. The grounding screw (M4 type) is

located near the power connector.

ATTENTION

This product is intended to be mounted

on a well-grounded

mounting surface, such as a metal panel.

The potential

difference between the two ground potentials must be zero. If

the potential difference is NOT zero, the product could be

permanently damaged.

SIM Card Socket

The OnCell G4302-LTE4 comes with two nano-SIM card sockets for

cellular communication. The nano-SIM card sockets are located on the

back panel protected by a rubber cover.

By default, the SIM card in the SIM1 slot will act as the primary SIM

card. To make SIM2 the default SIM, log in to the OnCell’s web UI, and

configure SIM2 as the primary card. When the OnCell device is turned

on, it will boot up based on the configuration information stored on the

designated primary SIM card.

- 10 -

Installing a SIM Card

STEP

1: Open the rubber cov e r.

STEP

2: Push the 2-slot SIM card tray

to release the tray.

STEP

3: Remove the t

ray and place the

SIM cards into the tray.

STEP

4: Insert the tray with the SIM cards back into the SIM socket.

You will hear a click indicating the tray is locked into place. When

inserted, close the rubber cover.

Inhaltsverzeichnis

Andere Moxa Technologies Netzwerk-Router Handbücher

Moxa Technologies

Moxa Technologies EtherDevice Switch EDS-G205 Handbuch

Moxa Technologies

Moxa Technologies EDS-305-M12 Handbuch

Moxa Technologies

Moxa Technologies TN-4900 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-G205A-4PoE Handbuch

Moxa Technologies

Moxa Technologies SDS-3008 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ToughNet TN-5516 Series Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Bedienungsanleitung

Moxa Technologies

Moxa Technologies IKS-6324 Series Handbuch

Moxa Technologies

Moxa Technologies NAT-102 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDR-G9010 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NSwitch Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-408A Handbuch

Moxa Technologies

Moxa Technologies NPort IA5150 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ToughNet Bedienungsanleitung

Moxa Technologies

Moxa Technologies PowerTrans PT-7728 Handbuch

Moxa Technologies

Moxa Technologies EDR-8010 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies SR3000 Bedienungsanleitung

Moxa Technologies

Moxa Technologies AirWorks AWK-1137C-EU Bedienungsanleitung

Moxa Technologies

Moxa Technologies OnCell 5004-HSPA Bedienungsanleitung

Moxa Technologies

Moxa Technologies ioLogik E1242 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-508 Handbuch

Moxa Technologies

Moxa Technologies ETHERDEVICE EDS-308 Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDR-G902-T Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-405 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise