Moxa Technologies AirWorks AWK-1137C-EU Bedienungsanleitung

P/N: 1802011370017

*1802011370017*

AWK-1137C Series

Quick Installation Guide

Moxa AirWorks

Version 7.1, January 2021

Technical Support Contact Information

www.moxa.com/support



- 2 -

Overview

The AWK-1137C industrial Wi-Fi client meets the growing need for faster

data transmission speeds and wider coverage by supporting IEEE

802.11n technology with a net data rate of up to 300 Mbps. The

AWK-1137C combines two adjacent 20 MHz channels into a single 40 MHz

channel to deliver a potent combination of greater reliability and more

bandwidth. The AWK-1137C can operate on either the 2.4 GHz or the

5 GHz band and is backward compatible with existing 802.11a/b/g

deployments.

Hardware Setup

This section covers the hardware setup for the AWK-1137C.

Package Checklist

Before installing the AWK-1137C, verify that the package contains the

following items. If any of these items is missing or damaged, please

contact your customer service representative for assistance.

•1 AWK-1137C wireless client

•2 2.4/5 GHz omni-directional antennas: ANT-WDB-ARM-0202

•DIN-rail kit

•Quick installation guide (printed)

•Warranty card

- 3 -

Panel Layout of the AWK-1137C

1. System LEDs: SYS, WLAN,

LAN1, LAN2, and SERIAL

2. LAN1: 10/100 BaseT(X) RJ45

port

3. LAN2: 10/100 BaseT(X) RJ45

port

4. RS-232/422/485 DB9 s

erial port

5. 3-pin terminal block

(ground/-/+)

6. M3 screw holes for antenna

bracket

7. Antenna B RP-SMA

8. Antenna A RP-SMA

9. 3-pin maintenance port for

engineers

10.

Reset button

11.

Screw holes for DIN-rail

mounting kit

- 4 -

12.

Screw holes for wall-mounting

kit

Mounting Dimensions

DIN-Rail Mounting

When shipped, the metal DIN-rail mounting kit is fixed to the back panel

of the AWK-1137C. Mount the AWK-1137C on the corrosion-free

mounting rail that adheres to the EN 60715 standard.

STEP 1:

Insert the upper lip of

the

DIN

-rail kit into the mounting

rail.

STEP 2:

Press the AWK

-1137C towards the

mounting rail until it

snaps

into place.

Unit = mm (inch)

- 5 -

To remove the AWK-1137C from the DIN rail, do the following:

STEP 1:

Pull down the latch on the

DIN

-rail kit with a screwdriver.

STEP 2 & 3:

Slightly pull the

AWK

-1137C forward and lift it up

to remove it from the mounting

rail.

Wall Mounting (Optional)

For some applications, it may be more convenient to mount the

AWK-1137C to a wall, as illustrated below:

STEP 1:

Remove the aluminum

DIN

-rail attachment

plate from the

AWK

-1137C, and then

attach the

wall

-mounting plates

with M3 screws,

shown in the adjacent

diagrams.

STEP 2:

Mounting the

AWK-1137C to a wall requires two

screws. Use

the AWK-1137C device, with

wall

-mounting

plates attached, as a guide to mark the

correct locations of the

two screws. The heads of the

screws should be less than 6.0 mm in diameter, and

the

shafts should be less than 3.5 mm in diameter, as

shown in the figure on the right.

Do not drive the screws in all the way—leave a space of about 2 mm to

allow room for sliding the wall-mounting panel between the wall and the

screws.

NOTE

Test the screw head and shank size by inserting the screws into

one of the keyhole

-shaped apertures of the wall-

mounting plates

before they are fixed to the wall.

- 6 -

STEP 3a:

Once the screws are fixed into the wall, insert the two screw heads

through the large opening of the keyhole-shaped apertures, and then

slide the AWK-1137C downwards, as indicated to the right. Tighten the

two screws for added stability.

STEP 3b:

Alternatively, i

nsert four screws directly

through the AWK

-1137C into the wall.

WARNING

•

This equipment is intended to be used in a

Restricted Access

Location, such as a dedicated computer room where only

authorized service personnel or users can gain access.

Such

personnel must be instructed about the fact that the metal

chassis of the equipment is extremely hot and may cause

burns.

•

Service personnel

or users have to pay special attention and

take special precautions before handling this equipment.

•

Only authorized, well-trained professionals s

hould be allowed

to access the Restricted Access Location. Access should be

controlled by the authority responsible for the location with

lock and key or a security identity system.

•

External metal parts are hot!! Pay special attention or

use

special protection before handling this equipment.

- 7 -

Wiring Requirements

WARNING

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your M

oxa AWK-1137C.

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes that dictate the

maximum current allowed for each wire size. If the current goes

above the maximum ratings, the wiring could overheat, causing

serious damage to your equipment.

You should also pay attention to the following items:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE

Do not run signal or communications wiring and power wiring in

the same wire conduit. To avoid interference, wires with different

signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring with similar electrical characteristics can be bundled

together.

•Keep input wiring and output wiring separate.

•It is strongly advised that you label wiring to all devices in the system

when necessary.

ATTENTION

This product is intended to be supplied by a UL

-listed power

adapter suitable for use at

a Thermom

echanical Analysis (TMA) of

5 degree Celsius, which output meets SELV circuit and LPS

standards;

output rated 9 to 30 VDC, 1.3A min. or 24 VDC

, 0.49A

min.

ATTENTION

Make sure

the external power adapte

r (includes power cords and

plug assemblies) provided with the unit is certified and suitable

for use in your country.

- 8 -

Grounding the Moxa AWK-1137C

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well

-grounded

mounting surface, such as a metal panel.

There must be no

electrical potential difference betwee

n any two grounding points

;

otherwise, there is a risk that the device could be destroyed.

Installing Cable Extended Antennas for Outdoor Applications

If the antenna or the AWK device is installed outdoors or in an open-air

setting, proper lightning protection is required to prevent direct lightning

strikes on the AWK device. In order to prevent coupling currents from

nearby lightning strikes, a lightning arrester should be installed as part of

your antenna system. Ground the device, antenna, as well as the arrester

properly to provide maximum outdoor protection for the device.

Arrester Accessories

•SA-NMNF-01: Surge arrester, N-type (male) to N-type (female)

•SA-NFNF-01: Surge arrester, N-type (female) to N-type (female)

- 9 -

Wiring the Power Input

The 3-contact terminal block connector on the AWK-1137C’s side panel is

used for the AWK-1137C’s DC input. The top and front views of the

terminal block connector are shown below:

STEP 1:

Insert the negative/positive DC wires into the

V-/

V+

terminals.

STEP 2:

To keep the DC wires from pulling

loose, use a small

flat

-blade screwdriver to tighten the wire-clamp

screws on the front of the terminal block c

onnector.

STEP 3:

Insert the plastic terminal block connector prongs

into the terminal block receptor, which is located on

the

AWK-1137C’s side panel.

NOTE

Input Terminal Block (CN1) is suitable for wire size range of

-28 AWG (3.31-0.0804 mm²) and a torque value of 4.5 lb-in

(0.51 Nm)

ATTENTION

If the AWK

1137C is connected to a motor or other similar type of

equipment, be sure to use power isolation protection. Before

connecting the

AWK-1137C to the DC power inputs, make sure

the DC power source voltage is stable.

Using the Reset Button

The Reset button is used to load the factory default settings. Use a

pointed object to hold the Reset button down for five seconds to load the

factory defaults.

Activating AeroMag Function

Push the Reset Button five times to activate AeroMag. To deactivate it

again, push the Reset Button three times.

- 10 -

Installing the Antenna-Locking Clamp

Use the antenna-locking clamp to secure the antennas to the AWK-1137C

for added stability when you install the device in a high-vibration

environment.

STEP 1:

Slide the

locking clamps through

the

antenna port

STEP 2:

Use s

crews to fix the clamps to the

side

panel of the AWK-1137C as

shown below:

Communication Connections

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) ports located on the AWK-1137C’s front panel are

used to connect to Ethernet-enabled devices.

The pinouts for both the MDI (NIC-type) and MDI-X (HUB/switch-type)

ports as shown below:

MDI Port Pinouts

MDI-X Port Pinouts

8-pin RJ45

Signal

Tx+

Tx-

Rx+

Rx-

Signal

Rx+

Rx-

Tx+

Tx-

RS-232/422/485 Serial Port

The AWK-1137C has 1 RS-232/422/485 serial port with DB9 connector

for serial-to-WLAN connectivity. The pin assignments for the serial ports

are shown below:

Pin RS-232

RS-422/485

(4W)

RS-485

(2W)

DCD

TxD-(A)

–

RxD

TxD+(B)

–

TxD

RxD+(B)

Data+(B)

DTR

RxD-(A)

Data-(A)

GND

DSR

–

RTS

–

CTS

–

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies Netzwerk-Router Handbücher

Moxa Technologies

Moxa Technologies TN-5916 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ioLogik E1210 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDR-G902 Handbuch

Moxa Technologies

Moxa Technologies AWK-4121 Bedienungsanleitung

Moxa Technologies

Moxa Technologies ToughNet TN-5516 Series Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-G308 Handbuch

Moxa Technologies

Moxa Technologies OnCell 5004 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDR-G902-T Bedienungsanleitung

Moxa Technologies

Moxa Technologies ToughNet Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice Switch EDS-G205 Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDS-P506A-4PoE Series Handbuch

Moxa Technologies

Moxa Technologies EDS-408A Handbuch

Moxa Technologies

Moxa Technologies EDS-518E Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-405 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NSwitch Bedienungsanleitung

Moxa Technologies

Moxa Technologies NAT-102 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies OnCell G4302-LTE4 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies E Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-505A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ioLogik E1200 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Bedienungsanleitung

Moxa Technologies

Moxa Technologies OnCell 5004-HSPA Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-518E Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise