Moxa Technologies CP-132EL Series Bedienungsanleitung

P/N: 1802001320021

*1802001320021*

CP-132EL/CP-132EL-I

Quick Installation Guide

PCI Express Multiport Serial Board

Edition 2.0, February 2017

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

Moxa’s new PCI Express multiport serial boards, the CP-132EL and

CP-132EL-I, are designed for POS and ATM applications and for use by

industrial automation system manufacturers and system integrators. The

boards are compatible with all popular operating systems and support

data rates of up to 921.6Kbps as well as full modem control signals,

ensuring compatibility with a wide range of serial peripherals. In addition,

the CP-132EL and CP-132EL-I work with PCI Express ×1, allowing the

boards to be installed in any available PCI Express slot (including ×1, ×2,

×4, ×8, ×16, and ×32).

Package Checklist

Before installing the PCI Express board, verify that the package contains

the following items:

•1 PCI Express serial board

•Documentation and Software CD

•Quick installation guide (printed)

•Low Profile Bracket

Notify your sales representative if any of the above items is missing or

damaged.

Hardware Installation Procedure

The PCI Express board MUST be plugged into the PC before the driver is

installed. Follow these steps to install the board in the PC.

STEP 1: Power off the PC.

STEP 2: Plug the board firmly into an open PCI Express slot.

STEP 3: Fasten the holding screw to fix the control board in place.

STEP 4: Connect the connection cable.

STEP 5: Power on the PC; the BIOS will automatically set the IRQ and I/O

address.

Software Installation Information

The board MUST be plugged in before installing the driver. See the

previous section for instructions on how to install the board in your PC.

Refer to the PCI Express Board User’s Manual for detailed instructions on

installing the drivers for this board.

NOTE

The following procedure shows how to install the CP-132EL

driver.

- 3 -

Windows 2008/Vista (32-bit/64-bit) Driver Installation

1. After powering on your PC, Windows 2008 will automatically detect

the PCIe board.

2. Insert the PCIe software CD in your CD-ROM drive.

3. Select Locate and install driver software (recommended).

4. After selecting Search for driver software in this location, select

the Include subfolders, and then click Browse. If the system is a

32-bit (x86) platform, navigate to the \CP-132EL

Series\Software\Windows 2008_Vista\x86 folder on the CD,

if the system is 64-bit (x64) platform, navigate to the \CP-132EL

Series\Software\Windows 2008_Vista\x64 folder on the CD,

and then click Next to continue.

5. Click Install this driver software anyway in response to any

warnings that the software has not passed Windows Logo testing.

6. After the board has been installed, the installation wizard will guide

you through the port installation procedure. Port installation is

complete when Port 0 has been set up.

7. Use the Device Manager to check the installation of the board and

ports. Click the + sign next to Hardware, and then check

Multi-port serial adapters and Ports (COM & LPT). Click the

+sign next to Multi-port serial adapters, right-click on MOXA

CP-132EL Series (PCI Express Bus), select Properties, then

choose Port Configuration. Click the port to configure Interface

(RS-422, 2-wire RS-485, 4-wire RS-485) and Termination

Resistor (120Ω, Enable or Disable). If there are warning marks,

such as a question mark or exclamation point in front of the board or

port icons, examine the Event Log to determine the problem.

Windows 2003/XP (32-bit/64-bit) Driver Installation

1. After powering on your PC, Windows 2003/XP will automatically

detect the PCIe board.

2. Insert the PCIe software CD in your CD-ROM drive.

3. Select Install from a list or specific location (Advanced).

4. After selecting Search for the best driver in these locations,

select the Include this location in the search, and then click

Browse. If the system is a 32-bit (x86) platform, navigate to the

\CP-132EL Series\Software\Windows XP_2003\x86 folder

on the CD, if the system is 64-bit (x64) platform, navigate to the

\CP-132EL Series\Software\Windows XP_2003\x64 folder

on the CD, and then click Next to continue.

5. Click Continue Anyway in response to any warnings that the

software has not passed Windows Logo testing.

6. After the board has been installed, the installation wizard will guide

you through the port installation procedure, starting with port 0.

7. Use the Device Manager to check the installation of the board and

ports. Click the + sign next to Hardware, and then check

Multi-port serial adapters and Ports (COM & LPT). Click the

+sign next to Multi-port serial adapters, right-click on Moxa

CP-132EL Series (PCI Express Bus), select Properties, then

choose Port Configuration. Click the port to configure Interface

(RS-422, 2-wire RS-485, 4-wire RS-485) and Termination

Resistor (120Ω, Enable or Disable). If there are warning marks,

such as a question mark or exclamation point in front of the board or

port icons, examine the Event Log to determine the problem.

- 4 -

Windows 2000 Driver Installation

1. After powering on your PC, Windows 2000 will automatically detect

the PCIe board.

2. Insert the PCIe software CD in your CD-ROM drive.

3. Select Search for a suitable driver for my device

(recommended).

4. Under Optional search location, select specify a location.

Navigate to the \CP-132EL Series\Software\Windows 2K

folder on the software CD.

5. Click Continue Anyway in response to any warnings that the

software has not passed Windows Logo testing.

6. After the board has been installed, the installation wizard will guide

you through the port installation procedure, starting with port 0.

7. Use the Device Manager to check the installation of the board and

ports. Click the + sign next to Hardware, and then check

Multi-port serial adapters and Ports (COM & LPT). Click the

+sign next to Multi-port serial adapters, right-click on MOXA

CP-132EL Series (PCI Express Bus), select Properties, then

choose Port Configuration. Click the port to configure Interface

(RS-422, 2-wire RS-485, 4-wire RS-485) and Termination

Resistor (120Ω, Enable or Disable). If there are warning marks,

such as a question mark or exclamation point in front of the board or

port icons, examine the Event Log to determine the problem.

Linux Driver Installation

1. Execute the following commands from the Linux prompt:

#mount /dev/cdrom /mnt/cdrom

#cd /

#mkdir moxa

#cd /moxa

#cp /mnt/cdrom/<driver directory>/

driv_linux_smart_vx.x_build_yymmddhh.tgz .

#tar –xzvf

driv_linux_smart_vx.x_build_yymmddhh.tgz

2. #cd mxser

#make clean; make install

3. #cd /moxa/mxser/driver

#./msmknod

4. #modprobe mxupcie

5. Use the Moxa Port Configuration Tool to set Interface and

Termination Resistor for the MUE series. The MUE series includes

CP-102E, CP-102EL, CP-132EL, CP-132EL-I, CP-114EL, and

CP-114EL-I.

Usage: muestty <operation> device

Device: The MUE series device node

Operation: -h Help

-g Get interface and terminator type

-i intf Set interface type with options below

-t value Set termination resistor with options below

Intf RS422 RS-422 mode

RS4852W RS-485 2-wire mode

RS4854W RS-485 4-wire mode

Value NONTERM Non termination resistor

120TERM 120ohm termination resistor

- 5 -

For example:

To set the MUE interface

# muestty –i RS422 /dev/ttyMUE2

To set the MUE termination resistor

# muestty –t 120TERM /dev/ttyMUE2

6. Use the Moxa diagnostic utility to verify the driver status:

#cd /moxa/mxser/utility/diag

#./msdiag

7. Use the Moxa terminal utility to test the tty ports:

#cd /moxa/mxser/utility/term

#./msterm

Pin Assignments

The CP-132EL and CP-132EL-I boards have a female DB25 connector on

the board. In this section, we give the on-board connector’s pin

assignments to facilitate making your own connection cable, and the male

DB9 device-side pin assignments for the optional CBL-M25M9x2-50

cable.

Female DB25: Board-side Pin Assignments

Transmission Signals

RS-422

4-wire RS-485

2-wire RS-485

P2: TxD-(A)

–

P2: SGND

–

P2: TxD+(B)

–

P1: RxD-(A)

P1: Data-(A)

–

P1: RxD+(B)

P1: Data+(B)

–

P2: RxD-(A)

P2: Data-(A)

–

P2: RxD+(B)

P2: Data+(B)

P1: TxD-(A)

–

P1: SGND

–

P1: TxD+(B)

–

- 6 -

Male DB9 Connector: Device-side Pin Assignments

Transmission Signals

RS-422

4-wire RS-485

2-wire RS-485

TxD-(A)

–

TxD+(B)

–

RxD+(B)

Data+(B)

RxD-(A)

Data-(A)

GND

–

Specifications

Hardware

Connectors

Female DB25

Comm. Controller

16C550C compatible

Interface

Bus Interface

PCI Express ×1

Number of Ports

Max No. of Boards

Signal

RS-422

TxD+(B), TxD-(A), RxD+(B), RxD-(A), GND

RS-485 4-Wire

TxD+(B), TxD-(A), RxD+(B), RxD-(A), GND

RS-485 2-Wire

Data+(B), Data-(A), GND

Performance

Baudrate

50 bps to 921.6 Kbps

Configuration

Data Bits

5, 6, 7, 8

Stop Bits

1, 1.5, 2

I/O address/IRQ

BIOS assigned

Parity

None, Even, Odd, Space, Mark

Flow Control

XON/XOFF

Environment

Operating Temperature

0 to 55°C (32 to 132°F)

Operating Humidity

5 to 95% RH

Storage Temperature

-20 to 85°C (-4 to 185°F)

ESD Protection

Embedded 15 KV ESD Protection

Optical Isolation

2 KV (only for CP-132EL-I)

Regulatory Approvals

EN 55032, EN 55024, EN 61000-3-2,

EN 61000-3-3, EN 61000-6-2, IEC 61000-4-

IEC 61000-4-3, IEC 61000-4-4,

IEC 61000-4-5, IEC 61000-4-6,

IEC 61000-4-8, IEC 61000-4-11,

FCC Part 15 Class B

WARRANTY

5 years

Andere Handbücher für CP-132EL Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies PCI-Karte Handbücher

Moxa Technologies

Moxa Technologies CP-114UL Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies POS-104UL Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies CP-134N Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies Smartio CP-104UL Bedienungsanleitung

Moxa Technologies

Moxa Technologies PCI Express Board Bedienungsanleitung

Moxa Technologies

Moxa Technologies CP-118U Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies Industio CP134-UI Bedienungsanleitung

Moxa Technologies

Moxa Technologies CP-134U Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies CP-118U Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies Moxa Smartio C168H Bedienungsanleitung

Moxa Technologies

Moxa Technologies CP-134EL-A-I Bedienungsanleitung

Moxa Technologies

Moxa Technologies C320Turbo/PCI Bedienungsanleitung

Moxa Technologies

Moxa Technologies CP-118U-I Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies Smartio C104H/PCI Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies CP-132EL Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies WAPN002 Bedienungsanleitung

Moxa Technologies

Moxa Technologies CP-102E Bedienungsanleitung

Moxa Technologies

Moxa Technologies CP-104JU Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies CP-134U Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies CP-102U Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies CP-118EL Bedienungsanleitung

Moxa Technologies

Moxa Technologies CP-102U Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies CP-114EL-DB9M Bedienungsanleitung

Moxa Technologies

Moxa Technologies CP-132U Series Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung

Pyle

Pyle Gamelink PLINK1 Bedienungsanleitung