Moxa Technologies EtherDevice EDS-P206A-4PoE Series Bedienungsanleitung

P/N: 1802002060013

*1802002060013*

EDS-P206A-4PoE Series

Quick Installation Guide

Moxa EtherDeviceTM Switch

Edition 4.0, January 2017

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

The EDS-P206A-4PoE series industrial Ethernet switches are entry-level

industrial 6-port PoE Ethernet switches that support IEEE 802.3, IEEE

802.3u, and IEEE 802.3x, with 10/100M, full/half-duplex, MDI/MDIX

auto-sensing, IEEE 802.3af, and IEEE 802.3at.

The EDS-P206A-4PoE series provides 12/24/48 VDC redundant power

inputs that can be connected simultaneously to a live DC power source.

The switches are available with a standard operating temperature range

from -10 to 60°C, or with a wide operating temperature range from -40 to

75°C, and their IP30 metal housing makes them rugged enough for any

harsh industrial environment.

To provide greater versatility for use with applications from different

industries, the EDS-P206A-4PoE switches also allow users to enable or

disable broadcast storm protection with DIP switches on the outer panel.

The EDS-P206A-4PoE switches can be easily installed on a DIN-Rail or in

distribution boxes. The DIN-Rail mounting capability and IP30 metal

housing with LED indicators make the plug-and-play EDS-P206A-4PoE

switches reliable and easy to use.

NOTE

Throughout this Hardware Installation Guide, we use EDS as an

abbreviation for Moxa EtherDevice Switch:

EDS = Moxa EtherDevice Switch

Package Checklist

Your EDS is shipped with the following items. If any of these items are

missing or damaged, please contact your customer service

representative for assistance.

•Moxa EtherDevice™ Switch

•Quick installation guide (printed)

•Warranty card

Features

High-wattage Power-over-Ethernet

•Up to 30 watts per PoE port

•Active circuit protection

•Auto disconnection for over-voltage or under-voltage

•Power consumption detection and classification

High Performance Network Switching Technology

•10/100BaseT(X) (RJ45 connector), 100BaseFX (SC/ST connector,

multi/single-mode)

•10/100M, Full/Half-Duplex, MDI/MDIX auto-sensing

•IEEE 802.3/802.3u/802.3x

•Store and Forward switching process type, 2K address entries

Rugged Design

•Redundant dual 12/24/48 VDC power input

•Operating temperature range from -10 to 60°C, or extended

operating temperature of -40 to 75°C for “T” models.

•IP30 metal housing

•DIN-Rail or panel mounting capability

- 3 -

EDS-P206A-4PoE (Standard) Panel Layouts

1. Grounding screw

2. Terminal block for power

input P1/P2

3. DIP switches

4. Power input P1 LED

5. Power input P2 LED

6. PoE LED

7. 10/100BaseT(X) port

8. TP port’

s 10/100 Mbps LED

9. Model name

10.

Screw hole for wall

mounting kit

11.

DIN-Rail kit

- 4 -

EDS-P206A-4PoE-M-SC/ST Panel Layouts

NOTE: The EDS-P206A-4PoE-S-SC/ST are identical in appearance to the

EDS

-P206A-4PoE-M-SC/ST.

1. Grounding screw

Terminal block for power

input P1/P2

3. DIP switches

4. Power input P1 LED

5. Power input P2 LED

6. PoE LED

7. 10/100BaseT(X) port

8. TP port’s 10/100 Mbps

LED

9. Model name

10.

100BaseFX port

11.

FX port’s 100 Mbps LED

12.

Screw hole for wall

mounting kit

13.

DIN-Rail kit

- 5 -

EDS-P206A-4PoE-MM-SC/ST Panel Layouts

NOTE: The EDS-P206A 4PoE-SS-SC/ST are identical in appearance to the

EDS

-P206A-4PoE- MM-SC/ST.

1. Grounding screw

Terminal block for power

input P1/P2

3. DIP Switches

4. Power input P1 LED

5. Power input P2 LED

6. PoE LED

7. 10/100BaseT(X) port

8. TP port’s 10/100 Mbps

LED

9. Model name

10.

100BaseFX port

11.

FX port’s 100 Mbps LED

12.

Screw hole for wall

mounting kit

13.

DIN-Rail kit

- 6 -

Mounting Dimensions

Unit = mm (inch)

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should already be fixed to the

back panel of the EDS when you take it out of the box. If you need to

reattach the DIN-Rail attachment plate, make sure the stiff metal spring

is situated towards the top, as shown in the figures below.

STEP 1:

Insert the top of the

DIN

-Rail into the slot just

below the stiff metal spring.

STEP 2:

The DIN-Rail attachment

unit will snap into place as shown

below.

To remove the EDS from the DIN-Rail, reverse Steps 1 and 2 above.

- 7 -

Wall Mounting (optional)

For some applications, you will find it convenient to mount the

EDS-P206A-4PoE on the wall, as shown in the following figures.

STEP 1: Remove the

aluminum DIN

-Rail

attachment plate from

the

EDS

-P206A-4PoE’s rear

panel, and then attach the

wall mount plates as shown

the diagram at the right.

STEP 2: Mounting the EDS-P206A-4PoE on the wall

requires 4 screws. Use the

switch, with wall mount

plates attached, as a guide to mark the correct

locations of the 4 screws. The heads of the screws

should be less than 6.0 mm in diameter, and the shafts

should be less than 3.5

mm in diameter, as shown in

the figure at the right.

NOTE

Before tightening the screws into the wall, make sure the screw

head and shank size are suitable by inserting the screw into one

of the keyhole-shaped apertures of the wall mounting plates.

Do not screw the screws in completely—leave about 2 mm to allow room

for sliding the wall mount panel between the wall and the screws.

STEP 3: Once the screws are fixed

n the wall, insert the four screw

heads through the large parts of

the keyhole

-shaped apertures,

and then slide

the

EDS

-P206A-4PoE downwards, as

indicated. Tighten the four screws

for

added stability.

Wiring Requirements

WARNING

Safety First!

Turn the power off before disconnecting modules or wires. The

correct power supply voltage is listed on the product label. Check

the voltage of your power source to make sure that you are using

the correct voltage. Do NOT use a voltage greater than what is

specified on the product label.

- 8 -

WARNING

Safety First!

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowable for each wire size. If the current goes

above the maximum ratings, the wiring could overheat, causing

serious damage to your equipment.

You should also pay attention to the following points:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

in the same wire conduit. To avoid interference, wires with different

signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring that shares similar electrical characteristics can be

bundled together.

•Keep input wiring and output wiring separated.

•We strongly advise labeling the wiring to all devices in the system.

Grounding the EtherDevice Switch

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well

-grounded

mounting surface such as a metal panel.

Wiring the Redundant Power Inputs

The top two contacts and the bottom two contacts of the 4-contact

terminal block connector on the EDS’s top panel are used for the EDS’s

two DC inputs. Top and front views of one of the terminal block

connectors are shown here.

STEP 1: Insert the negative/positive DC wires into the

-/V+ terminals.

STEP 2:

To keep the

DC wires from pulling loose, use a

small flat

-blade screwdriver to tighten the wire-

clamp

screws on the front of the terminal block connector.

STEP 3:

Insert the plastic terminal block connector

prongs into the terminal block receptor, which is

located on

EDS’s top panel.

- 9 -

ATTENTION

Before connecting the EtherDevice Switch to the DC power

inputs, make sure the DC power source voltage is stable.

Communication Connections

The EDS-P206A-4PoE switches have 4, 5, or 6 10/100BaseT(X) Ethernet

ports, and 2, 1, or 0 (zero) 100BaseFX multi/single-mode (SC/ST-type

connector) fiber ports.

10/100BaseT(X) Ethernet Port Connection

10/100BaseT(X) ports located on the EDS’s front panel are used to

connect to Ethernet-enabled devices. Below we show pinouts for both

MDI (NIC-type) ports and MDI-X (HUB/Switch-type) ports, and also show

cable wiring diagrams for straight-through and cross-over Ethernet

cables.

MDI Port Pinouts

MDI-X Port Pinouts

8-pin RJ45

Signal

Tx+

Tx-

Rx+

Rx-

Signal

Rx+

Rx-

Tx+

Tx-

PoE 10/100BaseT(X) Ethernet Port Connection

PoE 10/100BaseT(X) ports located on the EDS switch’s front panel are

used to connect to PoE-enabled devices. The pinout follows the

“Alternative A, MDI-X mode” of 802.3af/at standards. Please see the

details in the following table.

PoE Port Pinout

8-pin RJ45

Data

Power

Tx+

V-

Tx-

V-

Rx+

V+

Rx-

V+

NOTE

According to IEEE 802.3af/at standards, the PD shall be

implemented to be insensitive to the polarity of the power supply

and shall be able to operate per MDI mode and MDI

-X mode.

However, some PD

s only support MDI mode or MDI-

X mode only.

The following

figure shows how to select the correct cable

between the PD and EDS-P206A-4POE.

- 10 -

RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring

RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring

NOTE

If the PD only supports MDI mode (V+, V+, V-, V- for pins 1, 2, 3,

6), choose

a cross-over

Ethernet cable to connect the PD and the

EDS switch. If the PD only support

s MDI-X mode (V-, V-

, V+, V+

for pin

s 1, 2, 3, 6), choose a straight-through Ethernet cable

between the PD and the EDS-P206-4PoE switch.

100BaseFX Ethernet Port Connection

The concept behind the SC/ST port and cable is straightforward. Suppose

you are connecting devices I and II; contrary to electrical signals, optical

signals do not require a circuit in order to transmit data. Consequently,

one of the optical lines is used to transmit data from device I to device II,

and the other optical line is used transmit data from device II to device I,

for full-duplex transmission.

Remember to connect the Tx (transmit) port of device I to the Rx (receive)

port of device II, and the Rx (receive) port of device I to the Tx (transmit)

port of device II. If you make your own cable, we suggest labeling the two

sides of the same line with the same letter (A-to-A and B-to-B, as shown

below, or A1-to-A2 and B1-to-B2).

SC-Port Pinouts

SC-Port to SC-Port Cable Wiring

Andere Handbücher für EtherDevice EDS-P206A-4PoE Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies Schalten Handbücher

Moxa Technologies

Moxa Technologies PowerTrans PT-7528-24TX-WV Bedienungsanleitung

Moxa Technologies

Moxa Technologies MDS-G4000-4XGS Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-208A series Handbuch

Moxa Technologies

Moxa Technologies PT-G503-PHR-PTP Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-P206A-4PoE Series Handbuch

Moxa Technologies

Moxa Technologies PT-7728 Series Handbuch

Moxa Technologies

Moxa Technologies PT-7728 Series Handbuch

Moxa Technologies

Moxa Technologies EDS-G4014 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ToughNet Switch TN-5500 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MDS-G4000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IKS-6728-8PoE Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDS-P506E-4PoE Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-2005-ELP Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MDS-G4000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PT-7324 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICS-G7 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PT-7528-24TX-HV Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-828 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-P510A-8PoE Series Handbuch

Moxa Technologies

Moxa Technologies TN-5508A Series Handbuch

Moxa Technologies

Moxa Technologies TN-5305 Series Handbuch

Moxa Technologies

Moxa Technologies PT-G510 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-405A/408A Series Handbuch

Moxa Technologies

Moxa Technologies PT-G7728 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung