MuxLab 500086 Bedienungsanleitung

8495 Dalton Rd, Montreal, Quebec, Canada. H4T 1V5

Tel: (514) 905-0588 Fax: (514) 905-0589

Toll Free (North America): (877) 689-5228

E-mail: videoease@muxlab.com URL: www.muxlab.com

Specifications

Environment

Digital Audio

Standard Supported

LPCM, Dolby Digital® 5.1, DTS, and Dolby® True HD

Input / Output signal

S/PDIF coax cable or TOSLINK optic cable, input selectable.

Sampling rate

Up to 96kHz/24bits

Maximum distance between

unit

500 ft. (150m)

Connectors

RCA, TOSLINK, POWER, RJ45 on each unit.

Power requirement

1W max, 5V DC

S/PDIF spec

Coax 75 ohm with RCA connector,

level: 500mVp-p into 75 ohm

TOSLINK spec

Plastic optic cable with EIAJ/JEITA RC-5720C connector,

Wavelength: red 660nm, level: -15dBm max.

Cabling Requirement

(not supplied)

Any 4-pair straight cable CAT5/5E/6 with RJ-45 connector.

Coax and second Optic Cable.

Included in this kit

1 x TX unit, 1 x RX unit, 1 x 5V Power supply,

1 x Optic Cable 3ft (1m) and 1 x Installation guide.

RJ45 Pin Configuration

Pair 4+5 (data), 1+2+7(+5V), 3+6+8(0V)

Compatible mounting

hardware

500902, 500900, 500910, 500915

Temperature

Operating: -40° to 85°C (-40° to 185°F)

Storage: -40° to 85°C (-40° to 185°F)

Humidity

Maximum 95% (non-condensing)

Enclosure

ABS UL94HB fire retardant plastic

Dimensions

2.25” x 2.25” x 1.0” (6 x 6 x 2.5 cm) each box.

Shipping Weight

1 lb. (450g)

Warranty

2 Years

Order Information

500086 Digital Audio Extender

DIGITAL AUDIO EXTENDER KIT

500086

Quick Installation Guide

Overview

The Digital Audio Extender allows one (1) source of digital audio signal: coax (S/PDIF)

or optic (TOSLINK) to be connected to a receiver: coax or optic to up to 500 ft. (150m)

in a point-to-point configuration. The Extender supports most standards to transmit two

channels of uncompressed lossless PCM audio or compressed 5.1/7.1 surround sound,

such as Dolby Digital Plus or DTS-HD High Resolution Audio (multichannel digital

audio Dolby Digital® 5.1, DTS, and Dolby® True HD).

Applications

Transmission of Digital Audio Signal

Installation

One source unit can be connected to one receiver unit using a CAT5/6 cable. To install

the unit, perform the following steps:

Caution: Do not attempt to open the housing. There are no user-serviceable parts

inside the unit. Opening the unit will void your warranty.

Do not connect the unit to a telecommunication outlet wired to unrelated

equipment. Making such a connection may damage the equipment and/or

the unit. Verify that the desired twisted pairs are not being used for other

LAN or telephone equipment.

1. Use a dedicated 4-pair Cat5e/6 cable between the source and the receiver unit.

2. Patch panels are compatible.

3. Verify the wiring is “straight-through”, has 4 twisted pairs and has the standard Ethernet

RJ45 connector.

4. Connect the 5V power supply to one side only. Any side can be used.

5. Connect the unit to the audio source, either by coax source or optic. On the source

side, select which type of input is used. Both sides can be connected but only one is

used to transmit audio. At the receiver side both outputs will contain the same

signal. Note that some AV system may require that you connect only one signal.

Troubleshooting

The following tables describe some of the symptoms, probable causes and possible solutions regarding

the unit:

Symptom

Probable Cause

Possible Solutions

No audio

No signal from source

Source off.

Power missing. Check led.

Check continuity on all pair.

Check if pairs are not swapped.

Check if the four pairs are present.

Malfunctioning unit.

Intermittent audio or

no audio

Cable too long

If you still can’t diagnose the problem, please call MuxLab Customer Technical Support at

877-689-5228 (toll-free in North America) or (+1) 514-905-0588 (International).

Inhaltsverzeichnis

Andere MuxLab Extender Handbücher

MuxLab

MuxLab 500115 Bedienungsanleitung

MuxLab

MuxLab 500041-WP-US Bedienungsanleitung

MuxLab

MuxLab ProDigital 500485 Bedienungsanleitung

MuxLab

MuxLab 500730 Bedienungsanleitung

MuxLab

MuxLab 500780 Bedienungsanleitung

MuxLab

MuxLab 500850 Bedienungsanleitung

MuxLab

MuxLab 500752 Bedienungsanleitung

MuxLab

MuxLab 500409 Bedienungsanleitung

MuxLab

MuxLab 500759-TX-Dante Bedienungsanleitung

MuxLab

MuxLab 500464-V2 Bedienungsanleitung

MuxLab

MuxLab 500390 Bedienungsanleitung

MuxLab

MuxLab 500770 Bedienungsanleitung

MuxLab

MuxLab 500759-TX-HLO Bedienungsanleitung

MuxLab

MuxLab 500114 Bedienungsanleitung

MuxLab

MuxLab 500456 Bedienungsanleitung

MuxLab

MuxLab 500409 Bedienungsanleitung

MuxLab

MuxLab 500401-WP-US Bedienungsanleitung

MuxLab

MuxLab 500405 Bedienungsanleitung

MuxLab

MuxLab 500449 Bedienungsanleitung

MuxLab

MuxLab 500462 Bedienungsanleitung

MuxLab

MuxLab 100504 Bedienungsanleitung

MuxLab

MuxLab 500417 Bedienungsanleitung

MuxLab

MuxLab VideoEase MonoPro XLR Benutzerhandbuch

MuxLab

MuxLab 500417 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung