MuxLab 500454-POE Bedienungsanleitung

8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5

Tel: (514) 905-0588 Fax: (514) 905-0589

Toll Free (North America): (877) 689-5228

E-mail: videoease@muxlab.com URL: www.muxlab.com

Specifications

Environment

HDMI1.3a (Supports the 3D feature of HDMI 1.4).

Devices

DVD, plasma, projectors, monitors, TV, PC, laptops, servers

supporting HDMI.

Transmission

Transparent to the user.

Bandwidth

340 MHz.

Signals

HDMI 1.3a protocol.

Connectors

Cables not included.

One (1) HDMI receptacle.

One (1) RJ45S forCat 5e/6 unshielded or shielded twisted pair.

Two (2) 3.5mm jacks for IR emitter and sensor.

One (1) DB9 Connector for RS-232.

Maximum Distance

Based on a maximum

length of 6.6 ft (2 m) of

HDMI cable per end.

Cat 5e/6: 230 ft (70 m) up to 1080P Deep Color

115 ft (35 m)for 4K; 3840 X2160/24,25,30 Hz

Note:When installed in an electrically noisy environment, an STP

cable must be used. Also, cross-connection reduces the effective

distance depending on the grade of twisted cable used.

RJ45 Pin

Configuration

Reverse Polarity

Sensitive. Use EIA/TIA

568A or 586B straight-

through wiring.

RJ45 Link

Pin 1 (R) Pin 2 (T)

Pin 3 (R) Pin 6 (T)

Pin 4 (R) Pin 5 (T)

Pin 7 (R) Pin 8 (T)

Cable

One (1) Cat 5e/6 or better twisted pair cablerequired

Power Supply

One (1) 110-240V/48VDC power supply with interchangeable blades.

Power Consumption

Transmitter: 1.6 Watt Receiver: 3.2 Watt

Temperature

Operating: 0° to 40°C Storage: -20° to 85°C

Humidity: Up to 95% non-condensing

Enclosure

Metal

Dimensions

4.40” x 3.00” x 1.00” (11.2 x 7.6 x 2.5 cm)

Weight

1.4 lb (0.6 kg)

Compliance

Regulatory: FCC, CE, RoHS Flammability: 94V0

Warranty

2 years

Order Information

500454-POE HDMI/RS232 Extender Kit, POE, HDBT, UHD-4K

500454-POE-RX HDMI/RS232 Receiver, PoE, HDBT, UHD-4K

HDMI/RS232 Extender Kit, PoE, HDBT, UHD-4K

500454-POE (Kit), 500454-POE-RX (Receiver only)

Quick Installation Guide

Overview

The HDMI/RS232 Extender Kit, PoE, HDBT, UHD-4K (500454-POE) allows HDMI

equipment to be connected up to 230 ft (70 m) @ 1080p via one (1) Cat 5e/6 unshielded

twisted pair cable in a point-to-point configuration. The 500454-PoE includes one (1)

Transmitter and one (1) Receiver as well as an IR Emitter (500998) and IR Sensor

(500999) for remote control applications. The unit comes with one (1) power supply, as

it only require power on the Transmitter or Receiver side and provides PoE/PoC power

to the opposite end extender. The 500454-POE-RX receivers may be used in

conjunction with MuxLab’s HDMI Matrix Switch. For installation instructions, please

refer to the HDMI Matrix Switch Installation Guide.

Applications

Applications include digital signage, commercial and residential AV systems, classroom

projector systems, boardroom systems, collaborative PC systems, and medical

information systems.

Installation

1. Identify the connectors on the Transmitter and Receiver as indicated on the product

end panels.

2. Verify that the distance between the HDMI Transmitter and Receiver is within

MuxLab specifications (see specifications table).

3. To install the Transmitter:

3a. Connect the Transmitter to the HDMI video source with an HDMI compliant

cable.

3b. Connect one (1) length of Cat 5e/6 (or higher) grade UTP cable to the

RJ45 LINK connector on the Transmitter.

4. To install the Receiver:

4a. Connect the Receiver to the HDMI display equipment with an HDMI compliant

cable.

Note: When used with MuxLab’s HDMI Matrix Switch, please consult the Matrix

Switch Installation Guide.

4b. Connect one (1) Cat 5e/6 cable to the RJ45 LINK connector on the Receiver.

5. Connect the 48VDC power supply to either the Transmitter or Receiver first, and

then plug the power supply into an AC power outlet. Only one end (TX or RX end)

needs to be connected to a power supply, which then powers the extender at the

opposite end. If power is present, the green power LED of the Transmitter and the

Receiver will be ON.

Note: Power-up the HDMI / RS232 Extender kit, PoE, HDBT, UHD-4K only after

all connections are made.

6. Power-up the HDMI equipment and verify the image quality.

7. This product support bi-directional IR control. If infrared remote control is needed

to control the Source equipment from the Display, connect the IR Sensor to the

3.5mm Stereo Jack of the receiver and the IR Emitter to the 3.5mm Mono Jack of

the Transmitter.

Note: The IR Sensor can be distinguished from the IR Emitter by looking at the

3.5-mm plug. The IR Sensor has a 3.5mm stereo plug (3 Contacts) and the

IR Emitter has a 3.5mm mono plug (2 Contacts).

8. Position the IR Sensor so that it is aimed toward the hand-held remote control. For

clear IR signal reception, aim the hand-held remote control toward the top of the IR

Sensor enclosure.

9. Position the IR Emitter as close as possible to the source’s IR Sensor (i.e. DVD,

Blu-ray, or media player). For a clear IR signal reception, the IR Emitter may be

affixed to the source’s IR Sensor. The IR Emitter’s signal is transmitted from the

side of the enclosure.

10. If infrared remote control is needed to control the Display equipment from the

Source, connect the IR Emitter to the Receiver’s 3.5mm stereo jack and connect the

IR Sensor to the Transmitter’s 3.5mm mono jack.

11. The 500454-PoE also supports RS232 pass-thru in order to allows a device such as

commercial monitors to be controlled as in digital signage application. Please refer

to the following diagram for the cabling connection.

12. The following diagram shows the final configuration.

Troubleshooting

The following table describes some of the symptoms, probable causes and possible solutions

in regard to the installation of the HDMI/RS232 Extender Kit, PoE, HDBT, UHD-4K:

Symptom

Tx LEDs

Rx LEDs

Probable

Cause

Possible

Solutions

Power

HDMI

RJ45

Power

HDMI

RJ45

No Image

OFF

No power

•Check power

connections.

No Image

OFF

UTP Cable

•Check the UTP

cables.

No Image

OFF

HDMI Cable

•Check the HDMI

Cable.

No Image

Synchronisation

•Check cable length.

Flickering

Image

Synchronisation

•Check cable length.

•Check the HDMI

Cable Quality.

Choppy sound

Synchronisation

•Check cable length.

•Check the HDMI

Cable Quality.

Green or pink

hue

DDC

communication

•Cycle power of the

HDMI Extender.

•Check UTP cables

and replace.

Image flickers

when powering

up nearby

equipment

Interference

•Use STP cables.

IR not

functioning

Remote control

not directed to

the IR Sensor or

IR Emitter not

directed to the

source.

•Make sure the IR

Sensor is directed

towards the remote

and the IR Emitter

to the equipment.

IR not

functioning

Interference

from sunlight,

Fluorescent,

Neon or

Halogen lights.

•Place the IR

equipment away

from the interfering

light.

IR not

functioning

Interference

from RF

radiation from

the TV.

•Place the IR

equipment away

from the RF

radiation.

If you still cannot diagnose the problem, please call MuxLab Customer Technical Support at

877-689-5228 (toll-free in North America) or (+1) 514-905-0588 (International).

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MuxLab Extender Handbücher

MuxLab

MuxLab 500757 Bedienungsanleitung

MuxLab

MuxLab 500757 Bedienungsanleitung

MuxLab

MuxLab 500460 Bedienungsanleitung

MuxLab

MuxLab 500457 Bedienungsanleitung

MuxLab

MuxLab 500465 Bedienungsanleitung

MuxLab

MuxLab DomoStream Bedienungsanleitung

MuxLab

MuxLab 500780 Bedienungsanleitung

MuxLab

MuxLab 500752 Bedienungsanleitung

MuxLab

MuxLab 500770 Bedienungsanleitung

MuxLab

MuxLab 500759 Bedienungsanleitung

MuxLab

MuxLab 500733 Bedienungsanleitung

MuxLab

MuxLab ProDigital 500485 Bedienungsanleitung

MuxLab

MuxLab 500710 Bedienungsanleitung

MuxLab

MuxLab 100509 Bedienungsanleitung

MuxLab

MuxLab 500752 Bedienungsanleitung

MuxLab

MuxLab 500756 Bedienungsanleitung

MuxLab

MuxLab 500456 Bedienungsanleitung

MuxLab

MuxLab 500072 Bedienungsanleitung

MuxLab

MuxLab 500759-TX-Dante Bedienungsanleitung

MuxLab

MuxLab 500140 Bedienungsanleitung

MuxLab

MuxLab 500417 Bedienungsanleitung

MuxLab

MuxLab 500502 Bedienungsanleitung

MuxLab

MuxLab 500390 Bedienungsanleitung

MuxLab

MuxLab 500454 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung