MuxLab 500457 Bedienungsanleitung

8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5

Tel: (514) 905-0588 Fax: (514) 905-0589

Toll Free (North America): (877) 689-5228

E-mail: videoease@muxlab.com URL: www.muxlab.com

Specifications

Environment

KVM, HDMI 1.4 & USB 2.0

Devices

KVM, Monitors, TV, PC, laptops, mouse, keyboard.

Transmission

Transparent to the user.

Bandwidth

340 MHz

Signals

HDMI 1.4 protocol and USB 2.0

USB

One input on TX side and 4 outputs on RX side.

Bandwidth available: Up to 250 Mb/s.

Connectors

One (1) HDMIreceptacle per TX & RX unit.

One (1) RJ45 for Cat 5e/6 UTP or STP per TX & RX unit.

On TX: 1 standard USB connector, type B.

On RX: 4 standard USB connectors, type A.

Two (2) 3.5mm jacks for IR sensor & emitter per TX & RX unit.

Note: Cables not included.

Maximum Distance

Based on a maximum

length of 6.6ft (2m) of

HDMI cable per end.

Cat 5e/6: 330ft (100m) up to1920 X 1200 resolution, up to 60Hz

330ft (100m) for 4K (3840 X 2160) up to 30Hz

Note: A minimum CAT5e/6 cable length of 12ft (4m) is required.

When installed in an electrically noisy environment, an STP cable

must be used.

RJ45 Pin

Configuration

Reverse Polarity

Sensitive. Use EIA/TIA

568A or 586B straight-

through wiring.

RJ45 Link

Pin 1 (R) Pin 2 (T)

Pin 3 (R) Pin 6 (T)

Pin 4 (R) Pin 5 (T)

Pin 7 (R) Pin 8 (T)

Cable

One (1) Cat 5e/6 or better twisted pair cablerequired.

Power Supply

Two (2) 110-240V/5VDC power supplies with interchangeable blades

Power Consumption

Transmitter: 3 Watts Receiver: 7 Watts + USB power

Temperature

Operating: 0° to 40°C Storage: -20° to 85°C

Humidity: Up to 95% non-condensing

Enclosure

Aluminum casting with plastic side panel.

Dimensions

4.50” x 3.00” x 1.25” (11.4 x 7.6 x 3.2 cm)

Weight

2.6 lb. (1.2 kg)

Compliance

Regulatory: FCC, CE, RoHS Flammability: 94V0

Warranty

2 years

Order Information

500457 HDMI/USB 2.0 Extender Kit

HDMI/USB 2.0 Extender Kit

500457

Quick Installation Guide

Overview

The HDMI/USB 2.0 Extender Kit allows one HDMI 1.4 and one USB 2.0 channel to be

transmitted up to 330ft (100m) at all resolutions up to 1920x1200 @ 60Hz via one (1)

Cat 5e/6 cable in a point-to-point configuration. The receive side includes a 4-port USB

2.0 hub, supporting KVM applications.

Applications

Applications include KMV commercial and residential AV systems, classroom projector

systems, digital signage, boardroom systems, collaborative PC systems, and medical

information systems.

Installation

1. Identify the connectors on the Transmitter and Receiver as indicated on the product

labels, see the above front and rear product views for further details.

2. Verify that the distance between the HDMI/USB 2.0 Transmitter and Receiver is

within MuxLab specifications.

3. To install the Transmitter:

3a. Connect the Transmitter to the HDMI video source with a HDMI compliant cable.

3b. Connect the Transmitter to the USB signal with a standard USB 2.0 cable.

3c. Connect a Cat 5e/6 (or higher) grade UTP cable of desired length within

specifications to the RJ45 LINK connector on the Transmitter.

4. To install the Receiver:

4a. Connect the Receiver to the HDMI display equipment with a HDMI compliant

cable.

4b. Connect the Receiver to as many as four (4) USB 2.0 peripherals with standard

USB 2.0 cables. Power is limited to 0.7A for the four (4) ports. An externally

powered four (4) port USB 2.0 hub may allow for expansion, or to support higher

power levels than 0.7A total.

4c. Connect the Cat 5e/6 cable coming from the Transmitter to the RJ45 LINK

connector on the Receiver.

5. Connect the 5 VDC power supply to the Receiver first, and then plug the power

supply into an AC power outlet. Next connect the 5 VDC power supply to the

Transmitter, and then plug the power supply into an AC power outlet. If power is

present, the power LED on the Transmitter and Receiver will be ON.

6. Power the HDMI equipment and verify the image quality.

7. This product supports unidirectional IR control. If infrared remote control is

needed to control the Source equipment from the Display, connect the IR Sensor

and/or IR Emitter to the 3.5mm Jacks of the Transmitter and Receiver.

8. Position the IR Sensor so that it is directed to the hand-held remote control. For a

clear IR signal reception, aim the hand-held remote control at the top of the IR

Sensor enclosure.

9. Position the IR Emitter as close as possible to the source’s IR Sensor (i.e. DVD

player). For a clear IR signal reception, the IR Emitter can be glued on the source’s

IR Sensor. The IR Emitter’s signal is transmitted from the side of the enclosure.

10. The following diagram shows the final configuration.

(Note: IR sensor and emitter not shown in above diagram.)

Troubleshooting

The following table describes some of the symptoms, probable causes and possible solutions

with respect to issues during the installation of the HDMI/USB 2.0 Extender Kit:

Note: The Act LED should blink when the unit is working. The HDMI LED will blink if the

source contains no HDCP.

Symptom

Tx unit LEDs

Rx unit LEDs

Probable

Cause

Possible

Solutions

Power

HDMI

RJ45

Power

HDMI

RJ45

No Image

OFF

No power

Check power

connections

No Image

OFF

UTP Cable

Check the UTP

cables.

No Image

OFF

HDMI Cable

Check the HDMI

cable.

No Image

(or

blink)

Cable length

Check cable length,

check with another

monitor.

Flickering

Image or bad

sound

(or

blink)

Cable length

Check cable length

Check the HDMI

cable.

No sound, but

image OK

(or

blink)

Sound at source

Check if source or

monitor is PCM or

Dolby/DTS.

Image flickers

when powering

up nearby

equipment

(or

blink)

Interference

Use STP cables

USB not

working, but

audio/video

USB 2.0 cable,

or too much

power required

for USB

peripheral.

Check USB 2.0 cable,

try another USB

device.

Adding

multiple USB

peripherals is

causing a

problem.

Too much

power required

for USB

peripherals.

Try a different USB

peripheral.

Try using an

externally powered

USB 2.0 hub.

If you still cannot diagnose the problem, please call MuxLab Customer Technical Support at

877-689-5228 (toll-free in North America) or (+1) 514-905-0588 (International).

Inhaltsverzeichnis

Andere MuxLab Extender Handbücher

MuxLab

MuxLab 500753 Bedienungsanleitung

MuxLab

MuxLab 500752 Bedienungsanleitung

MuxLab

MuxLab 500730 Bedienungsanleitung

MuxLab

MuxLab 500770 Bedienungsanleitung

MuxLab

MuxLab 500800 Bedienungsanleitung

MuxLab

MuxLab 500759-TX-HLO Bedienungsanleitung

MuxLab

MuxLab 500460-RX Bedienungsanleitung

MuxLab

MuxLab 500451 Bedienungsanleitung

MuxLab

MuxLab 500417 Bedienungsanleitung

MuxLab

MuxLab 500086 Bedienungsanleitung

MuxLab

MuxLab 500758 Bedienungsanleitung

MuxLab

MuxLab 500733 Bedienungsanleitung

MuxLab

MuxLab Pro Digital 500452 Bedienungsanleitung

MuxLab

MuxLab 500460 Bedienungsanleitung

MuxLab

MuxLab ProDigital 500485 Bedienungsanleitung

MuxLab

MuxLab 500464-V2 Bedienungsanleitung

MuxLab

MuxLab 500041-WP-UK Bedienungsanleitung

MuxLab

MuxLab 500070 Bedienungsanleitung

MuxLab

MuxLab 500732 Bedienungsanleitung

MuxLab

MuxLab 500752 Bedienungsanleitung

MuxLab

MuxLab 500756 Bedienungsanleitung

MuxLab

MuxLab 500462 Bedienungsanleitung

MuxLab

MuxLab 500459-100 Bedienungsanleitung

MuxLab

MuxLab 500409 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung