National Instruments CMS-9024 Bedienungsanleitung

MAINTAINING HARDWARE

NI CMS-9024

NI Condition Monitoring System for NI InsightCM™Enterprise

This document describes how to maintain the CMS-9024 NI Condition Monitoring System.

The CompactRIO-based CMS-9024 is a bundle of hardware and software that includes the

following components and features:

• cRIO-9024 controller and cRIO-9114 chassis

• NI C Series modules installed in the chassis

• Pre-installed NI InsightCM Server software

• Network configuration via USB drive

Note Complete the steps in the NI CMS-9024 and CMS-9068 Quick Start before

using this document.

Contents

CompactRIO Reconfigurable Embedded System.....................................................................2

Controller Front Panel...............................................................................................................2

Mounting the Chassis................................................................................................................3

Precautions to Take before Mounting the Chassis............................................................ 4

Measuring the Ambient Temperature of the Chassis........................................................ 4

Accommodating Air Circulation and Cabling Clearance................................................. 4

Mounting the Chassis Directly on a Flat Surface Using the Mounting Holes..................6

Mounting the Chassis the NI Panel Mounting Kit............................................................6

Mounting the Chassis on a DIN Rail................................................................................ 7

Mounting the Chassis on a Desktop..................................................................................8

Installing C Series I/O Modules in the Chassis.........................................................................8

I/O Module Arrangements................................................................................................ 9

Removing I/O Modules from the Chassis.........................................................................9

Connecting to a Network........................................................................................................ 10

Grounding the Chassis............................................................................................................ 10

Wiring Power to the Controller...............................................................................................10

Precautions to Take When Wiring Power to the Controller............................................11

Powering On the Controller.................................................................................................... 12

Understanding LED Indications on the Controller................................................................. 12

POWER LED..................................................................................................................12

FPGA LED......................................................................................................................12

STATUS LED..................................................................................................................13

USER1 LED....................................................................................................................13

Troubleshooting Network Communication.............................................................................13

Resetting the Network Configuration of the Controller..................................................14

Where to Go Next................................................................................................................... 15

Worldwide Support and Services............................................................................................ 15

CompactRIO Reconfigurable Embedded

System

The following figure shows the components of the CompactRIO reconfigurable embedded

system.

Figure 1. CompactRIO Reconfigurable Embedded System

1. cRIO-9024 intelligent real-time embedded controller

2. cRIO-9114 eight-slot reconfigurable embedded chassis

3. C Series I/O module

Controller Front Panel

The following figure shows the I/O ports and other features of the cRIO-9024 controller.

2| ni.com | Maintaining NI CMS-9024 Hardware for an NI InsightCM System

Figure 2. cRIO-9024 Controller Front Panel

NI cRIO-9024

CompactRIO Real-Time Controller

DO NOT SEPARATE CONNECTORS

WHEN ENERGIZED IN

HAZARDOUS LOCATIONS

SAFE MODE

CONSOLE OUT

IP RESET

NO APP

USER1

1: POWER

2: FPGA

3: STATUS

4: USER1

INPUT

9-35 V

35 W MAX

OFF

10/100

ACT/LINK

10/100/1000

1 2 3 4 V1

RESET ON

1. LEDs

2. Power connector

3. RS-232 Serial port

4. USB port

5. USB retention standoff

6. Reset button

7. DIP Switches

8. RJ-45 Ethernet port 1

9. RJ-45 Ethernet port 2

Note NI Condition Monitoring Systems do not use the DIP switches. Leave these

switches in the OFF position.

Mounting the Chassis

To obtain the maximum allowable ambient temperature of 70 °C, mount the chassis

horizontally on a flat, vertical, metallic surface such as a panel or wall. You can mount the

chassis directly to the surface or you can use the NI Panel Mounting Kit.

You can also mount the chassis in other orientations, on a nonmetallic surface, on a 35-mm

DIN rail, on a desktop, or in a rack, but mounting the chassis in these or other configurations

Maintaining NI CMS-9024 Hardware for an NI InsightCM System | © National Instruments | 3

can reduce the maximum allowable ambient temperature and can affect the typical accuracy of

modules in the chassis.

Note For more information about typical accuracy specifications for modules, visit

ni.com/info and enter the Info Code criotypical.

Refer to the following sections of this document for more information about mounting the

chassis in these configurations. Refer to the following table for additional resources you can

use when you consider an appropriate mounting configuration for your application.

Table 1. Additional Resources for Mounting Configurations

Consideration Resource

How can different mounting configurations

cause temperature derating?

Visit ni.com/info and enter the Info

Code criomounting.

How can different mounting configurations

affect the accuracy of C Series modules?

Visit ni.com/info and enter the Info

Code rdcriotemp.

What do I need to know about mounting the

chassis in environments with high shock and

vibration?

Visit ni.com/info and enter the Info

Code criomounting.

Precautions to Take before Mounting the Chassis

Before you mount the chassis, ensure that you have taken the following precautions:

• Record the serial number from the back of the chassis so that you can identify the

NI Condition Monitoring System in software. You cannot read the serial number after

you have mounted the chassis.

• Ensure that the chassis does not contain any I/O modules.

Measuring the Ambient Temperature of the Chassis

Measure the ambient temperature at each side of the chassis, 63.5 mm (2.5 in.) from the side

and 25.4 mm (1 in.) forward from the rear of the chassis.

Accommodating Air Circulation and Cabling Clearance

Your installation must meet the following requirements for space and cabling clearance:

• Allow 25.4 mm (1 in.) on the top and the bottom of the chassis for air circulation, as

shown in the following figure.

4| ni.com | Maintaining NI CMS-9024 Hardware for an NI InsightCM System

Figure 3. cRIO-9114 Front View with Dimensions and Air Circulation Requirements

1 2 3 4 5 6 7 8

88.1 mm

(3.47 in.)

Cooling Outline

25.4 mm (1.00 in.)

Cooling Outline

25.4 mm (1.00 in.)

165.1 mm (6.50 in.)

36.4 mm

(1.43 in.)

51.7 mm

(2.04 in.)

19.0 mm

(0.75 in.)

4.1 mm

(0.16 in.)

• Allow 50.8 mm (2 in.) in front of modules for cabling clearance for common connectors,

such as the 10-terminal, detachable screw terminal connector, as shown in the following

figure.

Figure 4. cRIO-9114 Cabling Clearance Requirements

274.0 mm (10.79 in.)

Minimum

144.0 mm

(5.7 in.)

Cabling Clearance

50.8 mm (2.00 in.)

93.1 mm

(3.66 in.)

4.1 mm (0.16 in.)

Refer to the following table for additional resources about system dimensions and cabling

clearance considerations.

Maintaining NI CMS-9024 Hardware for an NI InsightCM System | © National Instruments | 5

Table 2. Additional Resources for System Dimensions and Cabling Clearance

Consideration Resource

Where can I find more information about dimensions

of the system, included detailed dimensional

drawings?

Visit ni.com/dimensions.

Where can I find more information about the

minimum cabling clearance for C Series modules with

other connector types?

Visit ni.com/info and enter the

Info Code rdcrioconn.

Mounting the Chassis Directly on a Flat Surface Using

the Mounting Holes

Complete the following steps to mount the chassis directly on a flat, rigid surface using the

mounting holes in the chassis. National Instruments recommends that you mount the chassis in

this manner for environments with high shock and vibration.

1. Use the dimensions provided in this document to prepare the surface for mounting the

chassis.

2. Align the chassis on the surface.

3. Fasten the chassis to the surface using two M4 or number 10 panhead screws appropriate

for the surface, as shown in the following figure. Screws must be longer than

19 mm (0.75 in.) to pass all the way through the chassis. National Instruments does not

provide these screws with the chassis.

Figure 5. Mounting the cRIO-9114 Directly on a Flat Surface

1 2 3 4 5 6 7 8

Caution Ensure that the chassis does not contain any I/O modules before you

remove it.

Mounting the Chassis the NI Panel Mounting Kit

Complete the following steps to use the NI panel mounting kit (part number 779558-01) to

mount the chassis on a flat surface.

6| ni.com | Maintaining NI CMS-9024 Hardware for an NI InsightCM System

1. Fasten the panel mounting plate to the chassis using a number 2 Phillips screwdriver and

M4 × 22 screws. National Instruments provides these screws with the panel mounting kit.

You must use these screws because they are the correct depth and thread for the panel

mounting plate. Tighten the screws to a maximum torque of 1.3 N · m (11.5 lb · in.).

2. Fasten the panel mounting plate to the surface using the screwdriver and screws that are

appropriate for the surface. The maximum screw size is M5 or number 10.

Caution Ensure that the chassis does not contain any I/O modules before you

remove it.

Mounting the Chassis on a DIN Rail

Complete the following steps to use the NI 9915 DIN rail mounting kit (part number

779018-01) to mount the chassis on a standard 35-mm DIN rail.

1. Fasten the DIN rail clip to the chassis using a number 2 Phillips screwdriver and M4 × 22

screws, as shown in the following figure. National Instruments provides these screws

with the DIN rail mounting kit. Tighten the screws to a maximum torque of

1.3 N · m (11.5 lb · in.).

Figure 6. Installing the DIN Rail CLIP on the cRIO-9114

2. Insert one edge of the DIN rail into the deeper opening of the DIN rail clip, as shown in

the following figure.

Maintaining NI CMS-9024 Hardware for an NI InsightCM System | © National Instruments | 7

Figure 7. One Edge of the DIN Rail Inserted in a Clip

1. DIN rail clip

2. DIN rail

3. DIN rail spring

3. Press down firmly on the chassis to compress the spring until the clip locks in place on

the DIN rail.

Caution Ensure that the chassis does not contain any I/O modules before you

remove it.

Mounting the Chassis on a Desktop

You can use the NI 9901 desktop mounting kit to mount the chassis on a desktop. Install the

adapter bracket using two M3 × 20 screws. National Instruments provides the adapter bracket

and screws with the desktop mounting kit. Refer to the NI 9901 documentation for more

information about mounting the chassis on a desktop.

Installing C Series I/O Modules in the Chassis

Note Before you install a C Series I/O module in the chassis, ensure that no

I/O-side power is connected to the module. If the system is in a nonhazardous

location, the chassis power can be on when you install modules.

Complete the following steps to install a C Series I/O module in the chassis.

1. Align the module with a slot in the chassis, as shown in the following figure. The module

slots are labeled 1 to 8, left to right.

8| ni.com | Maintaining NI CMS-9024 Hardware for an NI InsightCM System

Figure 8. Installing a C Series I/O Module in the Chassis

1. Insertion groove

2. Latch

2. Squeeze the latches and insert the module into the slot.

3. Press firmly on the connector side of the module until the latches lock the module into

place.

4. Repeat these steps to install additional modules.

I/O Module Arrangements

NI InsightCM Server supports only dynamic C Series I/O modules, such as the NI 9232,

installed on the CMS-9024. You must fill module slots in ascending order starting with slot 1.

You cannot skip any slots but you do not have to use every slot.

Note You must connect tachometers to the module in slot 1. Do not connect any

other sensors to the module in slot 1.

Removing I/O Modules from the Chassis

Note Before you remove a C Series I/O module from the chassis, ensure that no

I/O-side power is connected to the module. If the system is in a nonhazardous

location, the chassis power can be on when you install modules.

Maintaining NI CMS-9024 Hardware for an NI InsightCM System | © National Instruments | 9

To remove a C Series I/O module from the chassis, squeeze the latches on both sides of the

module and pull the module from the chassis.

Connecting to a Network

Use a standard Category 5 (CAT-5) or better shielded, twisted-pair Ethernet cable to connect

the RJ-45 Ethernet port on the cRIO-9024 to an Ethernet hub.

Caution To prevent data loss and to maintain the integrity of your Ethernet

installation, do not use a cable longer than 100 m.

The first time you power up the cRIO-9024, it attempts to initiate a DHCP network

connection. If the cRIO-9024 cannot initiate a DHCP connection, it connects to the network

with a link-local IP address with the form 169.254.x.x. After the chassis powers up, you

must configure the network settings in Systems Manager.

Grounding the Chassis

Complete the following steps to connect the chassis grounding terminal to the grounding

electrode system of your facility.

1. Attach a ring lug to a 2.0 mm2 (14 AWG) or larger wire.

2. Remove the grounding screw from the grounding terminal on the right side of the chassis.

3. Attach the ring lug to the grounding terminal.

4. Tighten the grounding screw to 0.5 N · m (4.4 lb · in.) of torque.

5. Attach the other end of the wire to the grounding electrode system of your facility using a

method appropriate for the application.

Note If you use shielded cabling to connect to a C Series I/O module with a plastic

connector, attach the cable shield to the chassis grounding terminal using

1.3 mm2 (16 AWG) or larger wire. Attach a ring lug to the wire and attach the wire

to the chassis grounding terminal. Solder the other end of the wire to the cable

shield. Use shorter wire for better EMC performance.

For more information about ground connections, visit ni.com/info and enter the Info Code

emcground.

Wiring Power to the Controller

The cRIO-9024 requires an external power supply that meets device specifications. The

cRIO-9024 filters and regulates the supplied power and provides power for all I/O modules

installed in the chassis. The cRIO-9024 has one layer of reverse-voltage protection.

The following figure shows the terminal screws, which secure the wires in the screw terminals,

and the connector screws, which secure the power connector on the front panel.

10 | ni.com | Maintaining NI CMS-9024 Hardware for an NI InsightCM System

Andere Handbücher für CMS-9024

Inhaltsverzeichnis

Andere National Instruments Messgerät Handbücher

National Instruments

National Instruments NI PXI-4070 Bedienungsanleitung

National Instruments

National Instruments PCIe-5774 Bedienungsanleitung

National Instruments

National Instruments NI PXIe-1491 Bedienungsanleitung

National Instruments

National Instruments NI 9223 Handbuch

National Instruments

National Instruments 9219 Handbuch

National Instruments

National Instruments RM-26999 Handbuch

National Instruments

National Instruments PXIe-5665 Bedienungsanleitung

National Instruments

National Instruments NI 9421 Bedienungsanleitung

National Instruments

National Instruments PXIe-5774 Bedienungsanleitung

National Instruments

National Instruments PXI-4070 6 1/2 Digit FlexDMM Handbuch

National Instruments

National Instruments PXIe-5603 Bedienungsanleitung

National Instruments

National Instruments MON-10467 Bedienungsanleitung

National Instruments

National Instruments PXI-4130 Handbuch

National Instruments

National Instruments NI PXIe-5105 Bedienungsanleitung

National Instruments

National Instruments FD-11613 Bedienungsanleitung

National Instruments

National Instruments NI TB-2644 Bedienungsanleitung

National Instruments

National Instruments 779640-01 Bedienungsanleitung

National Instruments

National Instruments PXI-5663 Handbuch

National Instruments

National Instruments 4551 Bedienungsanleitung

National Instruments

National Instruments BNC-2810 Bedienungsanleitung

National Instruments

National Instruments NI PXI-5600 Bedienungsanleitung

National Instruments

National Instruments Module NI PXI-8250 Bedienungsanleitung

National Instruments

National Instruments USB-6210 Bedienungsanleitung

National Instruments

National Instruments NI 5102 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung