National Instruments NI PXIe-5105 Bedienungsanleitung

GETTING STARTED GUIDE

NI PXI/PXIe/PCI-5105

12-Bit 60 MS/s Oscilloscope

This document explains how to install, configure, and test the NI PXI/PXIe/PCI-5105

(NI 5105). The NI 5105 is an 8-channel, 60 MHz oscilloscope. The NI 5105 ships with the

NI-SCOPE instrument driver, which you use to program the device.

Note Before you begin, install and configure your chassis and controller.

To access NI 5105 documentation, navigate to Start»All Programs»National Instruments»

NI-SCOPE»Documentation.

Contents

Safety and Electromagnetic Compatibility............................................................................... 2

Verifying the System Requirements..........................................................................................2

Unpacking the Kit..................................................................................................................... 2

Preparing the Environment....................................................................................................... 3

PXI Express Modules........................................................................................................3

PXI Modules..................................................................................................................... 3

PCI Modules..................................................................................................................... 3

Kit Contents.............................................................................................................................. 4

Other Equipment............................................................................................................... 5

Installing the Software.............................................................................................................. 5

Installing the Hardware.............................................................................................................5

Installing the NI PXI/PXIe-5105...................................................................................... 5

Installing the NI PCI-5105................................................................................................7

Hardware Front Panel Connectors.................................................................................... 8

Configuring the Hardware in MAX.......................................................................................... 9

Programming the NI 5105.........................................................................................................9

NI-SCOPE Examples......................................................................................................10

Making a Measurement...........................................................................................................11

Making a Measurement with NI-SCOPE SFP................................................................ 11

Making a Measurement with LabVIEW......................................................................... 11

Setting Up SMC-Based Devices for Synchronization............................................................ 12

PXI Modules................................................................................................................... 12

PXI Express Modules......................................................................................................12

PCI Devices.....................................................................................................................12

Troubleshooting...................................................................................................................... 13

NI 5105 Does Not Appear in MAX................................................................................ 13

What Should I Do if the Module Fails the Self-Test?.....................................................13

Thermal Shutdown Error................................................................................................ 13

Where To Go Next.................................................................................................................. 14

Worldwide Support and Services............................................................................................ 15

Safety and Electromagnetic Compatibility

Caution Refer to the Read Me First: Safety and Electromagnetic Compatibility

document for important safety and electromagnetic compatibility information. To

obtain a copy of this document online, visit ni.com/manuals and search for the

document title.

For additional electromagnetic compatibility information, including any product-specific

installation or configuration requirements necessary to achieve the specified level of

electromagnetic compatibility performance, refer to the individual product specifications.

Verifying the System Requirements

To use the NI 5105, your system must meet certain requirements.

For more information about minimum system requirements, recommended system

requirements, and supported ADEs, refer to the readme for your selected software support.

Readmes are available on the driver software DVD and online at ni.com/updates.

Unpacking the Kit

Caution To prevent electrostatic discharge from damaging the device, ground

yourself using a grounding strap or by holding a grounded object, such as your

computer chassis.

1. Touch the antistatic package to a metal part of the computer chassis.

2. Remove the device from the package and inspect the device for loose components or any

other sign of damage.

Caution Never touch the exposed pins of connectors.

Notify NI if the device appears damaged in any way. Do not install a damaged device.

3. Unpack any other items and documentation from the kit.

Store the device in the antistatic package when the device is not in use.

2| ni.com | NI PXI/PXIe/PCI-5105 Getting Started Guide

Preparing the Environment

Ensure that the environment in which you are using the NI 5105 meets the following

specifications:

PXI Express Modules

Operating Environment

....................................................................Ambient temperature range 0 °C to 55 °C (Tested in accordance with

IEC-60068-2-1 and IEC-60068-2-2. Meets

MIL-PRF-28800F Class 3 low temperature

limit and MIL-PRF-28800F Class 2 high

temperature limit.)

....................................................................Relative humidity range 10% to 90%, noncondensing (Tested in

accordance with IEC-60068-2-56.)

............................................................................Maximum altitude 2,000 m (800 mbar) (at 25 °C ambient

temperature)

............................................................................Pollution Degree 2

Indoor use only.

PXI Modules

Operating Environment

....................................................................Ambient temperature range 0 °C to 55 °C (Tested in accordance with

IEC-60068-2-1 and IEC-60068-2-2.)

....................................................................Relative humidity range 10% to 90%, noncondensing (Tested in

accordance with IEC-60068-2-56.)

............................................................................Maximum altitude 2,000 m (at 25 °C ambient temperature)

............................................................................Pollution Degree 2

Indoor use only.

PCI Modules

Operating Environment

....................................................................Ambient temperature range 0 °C to 45 °C (Tested in accordance with

IEC-60068-2-1 and IEC-60068-2-2.)

....................................................................Relative humidity range 10% to 90%, noncondensing (Tested in

accordance with IEC-60068-2-56.)

NI PXI/PXIe/PCI-5105 Getting Started Guide | © National Instruments | 3

............................................................................Maximum altitude 2,000 m (at 25 °C ambient temperature)

............................................................................Pollution Degree 2

Indoor use only.

Caution Clean the hardware with a soft, nonmetallic brush. Make sure that the

hardware is completely dry and free from contaminants before returning it to

service.

For complete specifications, refer to specifications document for your device at ni.com/

manuals.

Kit Contents

Figure 1. NI 5105 Kit Contents

123

5 6 7 84

1. NI PCI-5105 Device

2. NI PXI-5105 Device

3. NI PXIe-5105 Device

4. Screw Kit, part number 191306A-01 (ships only

with PCI kit)

5. Driver Software DVD

6. NI PXI/PXIe/PCI-5105 Getting Started Guide (this

document)

7. Read Me First: Safety and Electromagnetic

Compatibility

8. Maintain Forced-Air Cooling Note to Users

4| ni.com | NI PXI/PXIe/PCI-5105 Getting Started Guide

Other Equipment

There are several required items not included in your device kit that you need to install or

operate the NI 5105.

•(PXI Express Devices) A PXI Express chassis with a controller and the chassis

documentation

•(PXI Devices) A PXI chassis, a PXI/SCXI combination chassis, or a PXI/CompactPCI

chassis with a controller and the chassis documentation

•(PCI Devices) A desktop computer and its documentation

Note If your application uses NI-TClk synchronization for PCI devices, you must

use a RTSI cable to connect the PCI devices. For more information, refer to NI

High-Speed Digitizers Help»Programming»Reference»NI-TClk

Synchronization Help.

Installing the Software

You must be an Administrator to install NI software on your computer.

1. Install an ADE, such as LabVIEW or LabWindows™/CVI™.

2. Insert the driver software media into your computer. The installer should open

automatically.

If the installation window does not appear, navigate to the drive, double-click it, and

double-click autorun.exe.

3. Follow the instructions in the installation prompts.

Note Windows users may see access and security messages during

installation. Accept the prompts to complete the installation.

4. When the installer completes, select Restart in the dialog box that prompts you to restart,

shut down, or restart later.

Installing the Hardware

Installing the NI PXI/PXIe-5105

Caution To prevent damage to the device caused by ESD or contamination, handle

the device using the edges or the metal bracket.

1. Ensure the AC power source is connected to the chassis before installing the modules.

The AC power cord grounds the chassis and protects it from electrical damage while you

install the modules.

2. Power off the chassis.

3. Inspect the slot pins on the chassis backplane for any bends or damage prior to

installation. Do not install a module if the backplane is damaged.

NI PXI/PXIe/PCI-5105 Getting Started Guide | © National Instruments | 5

4. Remove the black plastic connectors from all the captive screws on the module front

panel.

5. Identify a supported slot in the chassis. The following figure shows the symbols that

indicate the slot types.

Figure 2. Chassis Compatibility Symbols

NI PXIe-1062Q

12 3 45

1. PXI Express System Controller Slot

2. PXI Peripheral Slot

3. PXI Express Hybrid Peripheral Slot

4. PXI Express System Timing Slot

5. PXI Express Peripheral Slot

PXI modules can be placed in PXI peripheral slots or PXI Express Hybrid peripheral

slots. PXI Express modules can be placed in PXI Express peripheral slots, PXI Express

Hybrid peripheral slots, or PXI Express System Timing slots.

6. Touch any metal part of the chassis to discharge static electricity.

7. Ensure that the ejector handle is in the unlatched (downward) position.

8. Place the module edges into the module guides at the top and bottom of the chassis. Slide

the device into the slot until it is fully inserted.

Figure 3. Module Installation

NI PXIe-1075

1. Chassis

2. Hardware Module

3. Ejector Handle in Down (Unlatched Position)

9. Latch the module in place by pulling up on the ejector handle.

10. Secure the device front panel to the chassis using the front-panel mounting screws.

6| ni.com | NI PXI/PXIe/PCI-5105 Getting Started Guide

11. Cover all empty slots using filler panels or slot blockers to maximize cooling air flow.

12. Power on the chassis.

Note For more information about maximizing cooling air flow, refer to the

Maintain Forced-Air Cooling Note to Users included in your kit.

Installing the NI PCI-5105

1. Power off and unplug the computer.

2. Access the computer system expansion slots. This step might require you to remove one

or more access panels on the computer case.

3. Locate a compatible slot and remove the corresponding slot cover on the computer back

panel. NI 5105 modules can be inserted only into PCI slots.

4. Touch any metal part of the computer to discharge any static electricity.

5. Insert the module into the slot you selected. Gently rock the module in to place without

forcing it.

Figure 4. Module Installation

1. Module

2. System Expansion Slot

3. PC

6. Secure the module mounting bracket to the computer back panel rail.

Caution It is important to completely screw the device into the slot, both for

mechanical stability and for creating a solid ground connection, which reduces

signal noise. Improperly secured devices may affect the accuracy of device

specifications.

7. Replace any access panels on the computer case.

8. Plug in and power on your computer.

NI PXI/PXIe/PCI-5105 Getting Started Guide | © National Instruments | 7

Hardware Front Panel Connectors

Refer to the following figure and table for the NI 5105 front panels and signal connections.

Figure 5. NI 5105 Front Panels

PFI 1

CH 0

CH 1

CH 2

CH 3

CH 4

CH 5

CH 6

CH 7

60MHz Oscilloscope

CH 0

CH 5

CH 4

CH 3

CH 2

CH 1

PFI 1

CH 7

CH 6

60MHz Oscilloscope

PFI 1

CH 0

CH 1

CH 2

CH 3

CH 4

CH 5

CH 6

CH 7

Table 1. NI 5105 Front Panel Signal Connections

Connector Description Function

CH 0—CH 7 SMB jack Analog input connection; digitizes data and triggers

acquisitions

PFI 1 SMB jack Multipurpose PFI line for digital trigger in/out, and timebase

out.

8| ni.com | NI PXI/PXIe/PCI-5105 Getting Started Guide

Configuring the Hardware in MAX

Use Measurement & Automation Explorer (MAX) to configure your National Instruments

hardware. MAX informs other programs about which devices reside in the system and how

they are configured. MAX is automatically installed with NI-SCOPE .

1. Launch Measurement & Automation Explorer (MAX).

MAX should automatically detect the device you installed.

2. In the Configuration pane, double-click Devices and Interfaces to see the list of installed

devices. Installed devices appear under the name of their associated chassis.

3. Expand your Chassis tree item. MAX lists all devices installed in the chassis. Your

default device names may vary.

Note If you do not see your hardware listed, press <F5> to refresh the list of

installed devices. If the device is still not listed, power off the system, ensure

the device is correctly installed, and restart.

4. Record the device identifier MAX assigns to the hardware. Use this identifier when

programming the NI 5105.

5. The MAX self-test performs a basic verification of hardware resources. To self-test a

module in MAX, right click the module and select Self-Test.

6. Run the test panels on the device to verify the signal.

a) To access the test panels, right-click the device and select Test Panels. The

NI-SCOPE Soft Front Panel (SFP) launches automatically.

b) Do one of the following to connect a signal to the device:

• Connect an external signal by clicking Auto or by selecting the appropriate

device parameters for the signal.

• Connect a cable from PFI 1 to an input channel and select Utility»Probe

Compensation from the SFP menu.

Note The NI 5105 has self-calibration capabilities, which you can access

programmatically with NI-SCOPE and your ADE, or interactively with

NI-SCOPE SFP or MAX.

Related Information

Making a Measurement on page 11

Programming the NI 5105

You can acquire data interactively using the NI-SCOPE SFP, or you can use the NI-SCOPE

instrument driver to program your device in the supported ADE of your choice.

NI PXI/PXIe/PCI-5105 Getting Started Guide | © National Instruments | 9

Table 2. NI 5105 Programming Options

Application

Programming

Interface (API)

Location Description

NI-SCOPE SFP Available from the start menu at

Start»All Programs»National

Instruments»NI-SCOPE»NI-

SCOPE Soft Front Panel

The NI-SCOPE SFP acquires,

controls, analyzes, and presents

data, similar to stand-alone

oscilloscopes. The NI-SCOPE SFP

operates on the PC, so you can view

and control waveforms directly

from your computer. You can also

run multiple sessions of the

NI-SCOPE SFP simultaneously.

NI-SCOPE

Instrument Driver

LabVIEW—Available on the

LabVIEW Functions palette at

Measurement I/O»NI-SCOPE.

NI-SCOPE configures and operates

the device hardware and performs

basic waveform acquisition and

measurement options using

LabVIEW VIs or LabWindows/CVI

functions.

C or LabWindows/CVI—

Available at Program Files»IVI

Foundation»IVI»Drivers»

niScope.

Microsoft Visual C/C++—Use

examples located in the

<NIDocDir>\NI–SCOPE

\examples directory, where

<NIDocDir> is one of the

following directories:

• Windows 8/7/Vista—Users

\Public\Documents

\National

Instruments

• Windows XP—Documents

and Settings\All

Users\Shared

Documents\National

Instruments

You can modify an NI-SCOPE C

example to create an application

with Microsoft Visual C/C++. Copy

an NI-SCOPE example to copy

required project settings for include

paths and library files.

Alternatively, refer to the Creating

an Application with Microsoft

Visual C and C++ topic of the NI

High-Speed Digitizers Help to

manually add all required include

and library files to your project.

NI-SCOPE Examples

Examples demonstrate the functionality of the device and serve as programming models and

building blocks for your own applications. The NI Example Finder is a utility available for

some ADEs that organizes examples into categories and allows you to easily browse and

search installed examples. You can see descriptions and compatible hardware models for each

example, or see all the examples compatible with one particular hardware model.

10 | ni.com | NI PXI/PXIe/PCI-5105 Getting Started Guide

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere National Instruments Messgerät Handbücher

National Instruments

National Instruments NI PXI-5621 Bedienungsanleitung

National Instruments

National Instruments PXI-4130 Handbuch

National Instruments

National Instruments PXIe-4162 Bedienungsanleitung

National Instruments

National Instruments FD-11605 Bedienungsanleitung

National Instruments

National Instruments PXIe-5665 Gebrauchs- und Pflegehandbuch

National Instruments

National Instruments PCI-6810 Bedienungsanleitung

National Instruments

National Instruments 9775 Bedienungsanleitung

National Instruments

National Instruments MON-10467 Bedienungsanleitung

National Instruments

National Instruments NI 5734 Bedienungsanleitung

National Instruments

National Instruments NI 5102 Bedienungsanleitung

National Instruments

National Instruments RM-26999 Handbuch

National Instruments

National Instruments NI PXIe-4137 Handbuch

National Instruments

National Instruments USB-6210 Bedienungsanleitung

National Instruments

National Instruments PXI-5152 Handbuch

National Instruments

National Instruments PXIe-5763 Bedienungsanleitung

National Instruments

National Instruments NI PXI-5122 Handbuch

National Instruments

National Instruments FD-11603 Bedienungsanleitung

National Instruments

National Instruments PXIe-5663E Bedienungsanleitung

National Instruments

National Instruments PXIe-6570 Bedienungsanleitung

National Instruments

National Instruments Module NI PXI-8250 Bedienungsanleitung

National Instruments

National Instruments NI 9263 Bedienungsanleitung

National Instruments

National Instruments CP400X Bedienungsanleitung

National Instruments

National Instruments NI Bedienungsanleitung

National Instruments

National Instruments PXI-5661 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung