National Instruments Module NI PXI-8250 Bedienungsanleitung

INSTALLATION GUIDE

NI PXI-8250

NI PXI System Monitor Module

This document describes how to install and configure the NI PXI-8250.

Software Installation

The NI PXI-8250 ships with NI System Monitor software that includes the

driver for the module. Although this software offers programmatic access

to the information reported by the card, it is not required to operate the six

system status LEDs, the relay, or the power rail connections on the front

panel. Refer to the NI System Monitor Help for specific installation

instructions.

Notes The NI PXI-8250 will not be visible in Measurement & Automation Explorer

(MAX) after proper installation. You can see the module in Windows Device Manager

if the System Monitor driver is installed and Device Manager has been refreshed.

When adding or removing an NI PXI-8250 module from a Windows XP/2000/NT system,

you must be logged on with administrator-level permission.

Hardware Installation

The following instructions are for general module installation in the

specified chassis. Consult the PXI chassis user manual for a given chassis

for chassis-specific instructions and warnings related to installation or

module configuration.

NI PXI-8250 Installation Guide 2 ni.com

Cautions The NI PXI-8250 module may sustain damage or inflict damage on adjacent

modules if improperly installed.

Proper slot selection is required for the operation of this module. If the module is installed

in any other slot, the module will not operate and could potentially cause other adjacent

modules to not operate. Appendix A, Specifications, of the NI PXI-8250 User Manual lists

the typical power required for the NI PXI-8250 module.

The NI PXI-8250 is a sensitive electronic device shipped in an antistatic bag. Open only at

an approved workstation and observe precautions for handling electrostatic-sensitive

devices.

Note Install the NI PXI-8250 in only the right-most slot of an NI PXI-1042/1042Q

or NI PXI-1045. Hence, the NI PXI-8250 should only be installed in slot 8 of an

NI PXI-1042/1042Q chassis or slot 18 of an NI PXI-1045 chassis.

Complete the following steps to install the NI PXI-8250 module.

1. Power off and unplug the chassis.

Caution To protect yourself and the computer from electrical hazards, the chassis must

remain unplugged until the installation is complete.

2. Locate the rightmost (last numbered) slot of the NI PXI-1042/1042Q

or NI PXI-1045 chassis and ensure it is unused. If occupied, relocate

the module or remove the filler panel. Refer to Figure 1 for the location

of this slot on the NI PXI-1042/1042Q chassis, and Figure 2 for the

location of this slot on the NI PXI-1045 chassis.

Figure 1. Location of NI PXI-1042Q Slot for NI PXI-8250 Support

NI PXI-1042Q

Slot 8

©National Instruments Corporation 3 NI PXI-8250 Installation Guide

Figure 2. Location of NI PXI-1045 Slot for NI PXI-8250 Support

3. Touch a metal part on the chassis to discharge any static electricity that

might be on your clothes or body. Static electricity can damage the

hardware.

4. Insert the NI PXI-8250 module into the rightmost slot of a

NI PXI-1042/1042Q or NI PXI-1045. The correct position is slot 8 for

the NI PXI-1042/1042Q and slot 18 for the NI PXI-1045, as shown in

Figure 1 and Figure 2, respectively. Use the injector/ejector handle to

fully inject the device into place.

5. Screw the front panel of the NI PXI-8250 to the front panel mounting

rails of the chassis.

6. Install a system controller or verify that a system controller has been

installed in the controller slot.

7. Plug in and power on the chassis.

8. Plug in and power on the host computer if using a remote controller in

the chassis.

9. Allow the operating system to properly detect and identify the

NI PXI-8250 module.

10. Launch Windows Device Manager and refresh the view.

The NI PXI-8250 module should be visible in Windows Device Manager.

NI PXI-8250 Configuration

The NI PXI-8250 module is fully compatible with the industry standard

PXI Specification, Revision 2.2, and the PCI Local Bus Specification,

Revision 3.0, respectively. This compatibility allows the PXI system to

automatically perform all bus-related configuration and requires no user

interaction. Since the NI PXI-8250 does not require configuration in MAX

it does not show up in MAX.

Slot 18

NI PXI-1045

National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation.

Refer to the Terms of Use section on ni.com/legal for more information about National

Instruments trademarks. Other product and company names mentioned herein are trademarks or trade

names of their respective companies. For patents covering National Instruments products, refer to the

appropriate location: Help»Patents in your software, the patents.txt file on your media, or

ni.com/patents.

Andere Handbücher für Module NI PXI-8250

Inhaltsverzeichnis

Andere National Instruments Messgerät Handbücher

National Instruments

National Instruments PXI-4130 Handbuch

National Instruments

National Instruments PXI-5660 Bedienungsanleitung

National Instruments

National Instruments NI 9223 Handbuch

National Instruments

National Instruments NI PXIe-4080 Handbuch

National Instruments

National Instruments NI 9227 Handbuch

National Instruments

National Instruments PXIe-5763 Bedienungsanleitung

National Instruments

National Instruments VRTS Bedienungsanleitung

National Instruments

National Instruments NI Bedienungsanleitung

National Instruments

National Instruments PXIe-4136 Bedienungsanleitung

National Instruments

National Instruments PXIe-5667 Bedienungsanleitung

National Instruments

National Instruments USB-5683 Bedienungsanleitung

National Instruments

National Instruments PXIe-4162 Bedienungsanleitung

National Instruments

National Instruments VirtualBench VB-8012 Bedienungsanleitung

National Instruments

National Instruments PXI-5663 Handbuch

National Instruments

National Instruments PXI-4070 6 1/2 Digit FlexDMM Handbuch

National Instruments

National Instruments PXIe-5622 Bedienungsanleitung

National Instruments

National Instruments NI PXIe-1491 Bedienungsanleitung

National Instruments

National Instruments NI 4350 Bedienungsanleitung

National Instruments

National Instruments NI PXIe-4139 Handbuch

National Instruments

National Instruments NI 5105 Bedienungsanleitung

National Instruments

National Instruments PXIe-6570 Bedienungsanleitung

National Instruments

National Instruments NI PXI-5621 Bedienungsanleitung

National Instruments

National Instruments NI 9263 Bedienungsanleitung

National Instruments

National Instruments NI 9213 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung