National Instruments PXIe-5622 Bedienungsanleitung

GETTING STARTED GUIDE

NI PXIe-5622

16-bit 150 MS/s Digitizer

This document explains how to install, configure, and test the NI PXIe-5622 (NI 5622). The

NI 5622 is a 150 MS/s digitizer with onboard signal processing (OSP). The NI-SCOPE

instrument driver ships with the NI 5622 and programs the device.

Note Before you begin, install and configure your chassis and controller.

To access NI 5622 documentation, navigate to Start»All Programs»National Instruments»

NI-SCOPE»Documentation.

Contents

Electromagnetic Compatibility Guidelines...............................................................................1

Verifying the System Requirements..........................................................................................2

Unpacking the Kit..................................................................................................................... 2

Kit Contents...................................................................................................................... 3

Other Equipment....................................................................................................................... 3

Preparing the Environment....................................................................................................... 3

Installing the Software.............................................................................................................. 4

Installing the NI 5622............................................................................................................... 4

Hardware Front Panel Connectors.................................................................................... 6

Configuring the Hardware in MAX.......................................................................................... 7

Programming the NI 5622.........................................................................................................8

Troubleshooting........................................................................................................................ 9

Why Is the ACCESS LED Off When the Chassis is On?.................................................9

What Should I Do if the NI 5622 Doesn't Appear in MAX?............................................9

What Should I Do if the Module Fails the Self-Test?.....................................................10

Thermal Shutdown Error................................................................................................ 10

Where To Go Next.................................................................................................................. 11

Worldwide Support and Services............................................................................................ 11

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits for

electromagnetic compatibility (EMC) stated in the product specifications. These requirements

and limits provide reasonable protection against harmful interference when the product is

operated in the intended operational electromagnetic environment.

This product is intended for use in industrial locations. However, harmful interference may

occur in some installations, when the product is connected to a peripheral device or test object,

or if the product is used in residential or commercial areas. To minimize interference with

radio and television reception and prevent unacceptable performance degradation, install and

use this product in strict accordance with the instructions in the product documentation.

Furthermore, any changes or modifications to the product not expressly approved by National

Instruments could void your authority to operate it under your local regulatory rules.

Caution To ensure the specified EMC performance, operate this product only with

shielded cables and accessories.

Caution To ensure the specified EMC performance, the length of all I/O cables

must be no longer than 30 m (100 ft).

Verifying the System Requirements

To use the NI 5622, your system must meet certain requirements. For more information about

minimum system requirements, recommended system, and supported application development

environments (ADEs), refer to the readme, which is available on the software media or online

at ni.com/updates.

Unpacking the Kit

Caution To prevent electrostatic discharge (ESD) from damaging the device,

ground yourself using a grounding strap or by holding a grounded object, such as

your computer chassis.

1. Touch the antistatic package to a metal part of the computer chassis.

2. Remove the device from the package and inspect the device for loose components or any

other sign of damage.

Caution Never touch the exposed pins of connectors.

Note Do not install a device if it appears damaged in any way.

3. Unpack any other items and documentation from the kit.

Store the device in the antistatic package when the device is not in use.

2| ni.com | NI PXIe-5622 Getting Started Guide

Kit Contents

Figure 1. NI 5622 Kit Contents

NIPXIe-5622

16-BitIF Digitizer

ACCESS

IF IN

ACTIVE

dBM MAX

TTL

6.3Vp-p

MAX

2Vp-p

NOM

ESD

SENSITIVE

PFI 1

LK OUT

1 2 3 4

1. NI PXIe-5622

2. Driver Software DVD

3. NI PXIe-5622 Getting Started Guide (this

document)

4. Maintain Forced-Air Cooling Note to Users

Other Equipment

In addition to the items in your device kit, a PXI Express chassis with a controller and the

chassis documentation are required for installation and operation of the NI 5622.

Preparing the Environment

Ensure that the environment in which you are using the NI 5622 meets the following

specifications:

Operating Environment

Ambient temperature range 0 °C to 55 °C (Tested in accordance with

IEC 60068-2-1 and IEC 60068-2-2. Meets

MIL-PRF-28800F Class 3 low temperature

limit and MIL-PRF-28800F Class 2 high

temperature limit.)

Relative humidity range 10% to 90%, noncondensing (Tested in

accordance with IEC-60068-2-56.)

Maximum altitude 2,000 m (800 mbar) (at 25 °C ambient

temperature)

Pollution Degree 2

Indoor use only.

NI PXIe-5622 Getting Started Guide | © National Instruments | 3

Caution Clean the hardware with a soft, nonmetallic brush. Make sure that the

hardware is completely dry and free from contaminants before returning it to

service.

For more information, refer to the specifications document for the device at ni.com/manuals.

Installing the Software

You must be an Administrator to install NI software on your computer.

1. Install an ADE, such as LabVIEW or LabWindows™/CVI™.

2. Insert the driver software media into your computer. The installer should open

automatically.

If the installation window does not appear, navigate to the drive, double-click it, and

double-click autorun.exe.

3. Follow the instructions in the installation prompts.

Note Windows users may see access and security messages during

installation. Accept the prompts to complete the installation.

4. When the installer completes, select Restart in the dialog box that prompts you to restart,

shut down, or restart later.

Installing the NI 5622

Caution To prevent damage to the device caused by ESD or contamination, handle

the device using the edges or the metal bracket.

1. Ensure the AC power source is connected to the chassis before installing the modules.

The AC power cord grounds the chassis and protects it from electrical damage while you

install the modules.

2. Power off the chassis.

3. Inspect the slot pins on the chassis backplane for any bends or damage prior to

installation. Do not install a module if the backplane is damaged.

4. Remove the black plastic connectors from all the captive screws on the module front

panel.

5. Identify a supported slot in the chassis. The following figure shows the symbols that

indicate the slot types.

4| ni.com | NI PXIe-5622 Getting Started Guide

Figure 2. Chassis Compatibility Symbols

NI PXIe-1062Q

1. PXI Express System Controller Slot

2. PXI Peripheral Slot

3. PXI Express Hybrid Peripheral Slot

4. PXI Express System Timing Slot

5. PXI Express Peripheral Slot

6. Touch any metal part of the chassis to discharge static electricity.

7. Ensure that the ejector handle is in the unlatched (downward) position.

8. Place the module edges into the module guides at the top and bottom of the chassis. Slide

the device into the slot until it is fully inserted.

Figure 3. Module Installation

NI PXIe-1075

1. Chassis

2. Hardware Module

3. Ejector Handle in Down (Unlatched) Position

9. Latch the module in place by pulling up on the ejector handle.

10. Secure the device front panel to the chassis using the front-panel mounting screws.

Note Tightening the top and bottom mounting screws increases mechanical

stability and also electrically connects the front panel to the chassis, which can

improve the signal quality and electromagnetic performance.

11. Cover all empty slots using filler panels or slot blockers to maximize cooling air flow.

12. Power on the chassis.

NI PXIe-5622 Getting Started Guide | © National Instruments | 5

Hardware Front Panel Connectors

Figure 4. NI 5622 Front Panel

NI PXIe-5622

16-Bit IF Digitizer

ACCESS ACTIVE

PFI 1

IF IN

CLK IN

CLK OUT

TTL (+5 V MAX)

Table 1. NI 5622 Front Panel Signal Connections

Connector Description Function

IF IN SMA connector Analog input connection; digitizes data and triggers

acquisitions

PFI 1 SMB connector Digital trigger connection

6| ni.com | NI PXIe-5622 Getting Started Guide

Table 1. NI 5622 Front Panel Signal Connections (Continued)

Connector Description Function

CLK IN SMA connector Imports an external reference or sample clock to the digitizer

CLK OUT SMA connector Exports the digitizer reference or sample clock

Configuring the Hardware in MAX

Use Measurement & Automation Explorer (MAX) to configure your National Instruments

hardware. MAX informs other programs about which devices reside in the system and how

they are configured. MAX is automatically installed with NI-SCOPE .

1. Launch MAX.

2. In the configuration tree, double-click Devices and Interfaces to see the list of installed

devices.

Installed devices appear under the name of their associated chassis.

3. Expand your Chassis tree item.

MAX lists all devices installed in the chassis. Your default device names may vary.

Note If you do not see your device listed, press <F5> to refresh the list of

installed devices. If the device is still not listed, power off the system, ensure

the device is correctly installed, and restart.

4. Record the device identifier MAX assigns to the hardware. Use this identifier when

programming the NI 5622.

5. Self-test the device by selecting the device in the configuration tree and clicking Self-Test

in the MAX toolbar.

The MAX self-test performs a basic verification of hardware resources.

6. Run the test panels on the device to verify the signal.

a) To access the test panels, right-click the device and select Test Panels. The

NI-SCOPE Soft Front Panel (SFP) launches automatically.

b) Complete one of the following steps to connect a signal to the device:

• Connect an external signal and click Auto or select the appropriate device

parameters for the signal.

• Connect a cable from PFI 1 to an input channel and select Utility»Probe

Compensation from the SFP menu.

Note The NI 5622 has self-calibration capabilities, which you can access

programmatically with NI-SCOPE and your ADE, or interactively with

NI-SCOPE SFP or MAX.

NI PXIe-5622 Getting Started Guide | © National Instruments | 7

Programming the NI 5622

You can acquire data interactively using the NI-SCOPE SFP, or you can use the NI-SCOPE

instrument driver to program your device in the supported ADE of your choice.

Table 2. NI 5622 Programming Options

Application

Programming

Interface (API)

Location Description

NI-SCOPE SFP Available from the start menu at

Start»All Programs»National

Instruments»NI-SCOPE»NI-

SCOPE Soft Front Panel.

The NI-SCOPE SFP acquires,

controls, analyzes, and presents

data, similar to stand-alone

oscilloscopes. The NI-SCOPE SFP

operates on the PC, so you can view

and control waveforms directly

from your computer. You can also

run multiple sessions of the

NI-SCOPE SFP simultaneously.

NI-SCOPE

Instrument Driver

LabVIEW—Available on the

LabVIEW Functions palette at

Measurement I/O»NI-SCOPE.

The NI-SCOPE API configures and

operates the device hardware and

provides customizable acquisition,

control, analysis, and measurement

options using LabVIEW VIs or

LabWindows/CVI functions.

C or LabWindows/CVI—

Available at Program Files»IVI

Foundation»IVI»Drivers»

niScope.

Microsoft Visual C/C++—Use

examples located in the

<NIDocDir>\NI–SCOPE

\examples directory, where

<NIDocDir> is one of the

following directories:

• Windows 8/7/Vista—Users

\Public\Documents

\National

Instruments

• Windows XP—Documents

and Settings\All

Users\Shared

Documents\National

Instruments

You can modify an NI-SCOPE C

example to create an application

with Microsoft Visual C/C++. Copy

an NI-SCOPE example to copy

required project settings for include

paths and library files. Alternatively,

refer to the Creating an Application

with Microsoft Visual C and C++

topic of the NI High-Speed

Digitizers Help to manually add all

required include and library files to

your project.

8| ni.com | NI PXIe-5622 Getting Started Guide

Troubleshooting

Why Is the ACCESS LED Off When the Chassis is On?

The LEDs may not light until the device has been configured in MAX. Before proceeding,

verify that the NI 5622 appears in MAX.

If the ACCESS LED fails to light after you power on the chassis, a problem may exist with the

chassis power rails, a hardware module, or the LED.

Caution Apply external signals only while the NI 5622 is powered on. Applying

external signals while the device is powered off may cause damage.

1. Disconnect any signals from the module front panels.

2. Power off the chassis.

3. Remove the module from the chassis and inspect it for damage. Do not reinstall a

damaged device.

4. Reinstall the module in a different chassis slot.

5. Power on the chassis.

6. Verify that the device appears in MAX.

7. Reset the device in MAX and perform a self-test.

Related Information

Installing the NI 5622 on page 4

What Should I Do if the NI 5622 Doesn't Appear in

MAX?

1. In the MAX configuration tree, expand Devices and Interfaces.

2. Expand the Chassis tree to see the list of installed devices, and press <F5> to refresh the

list.

3. If the module is still not listed, power off the system, ensure that all hardware is correctly

installed, and restart the system.

4. Navigate to the Device Manager.

Operating System Description

Windows 8 Right-click the Start screen, and select All apps»Control Panel»

Hardware and Sound»Device Manager.

Windows 7 Select Start»Control Panel»Device Manager.

Windows Vista Select Start»Control Panel»System and Maintenance»Device

Manager.

NI PXIe-5622 Getting Started Guide | © National Instruments | 9

Operating System Description

Windows XP Select Start»Control Panel»System»Hardware»Device

Manager.

5. If you are using a PXI or PXI Express controller, verify that a National Instruments

entry appears in the system device list. Reinstall NI-SCOPE and the device if error

conditions appear in the list. If you are using an MXI controller, right-click PCI-to-PCI

Bridge, and select Properties from the shortcut menu to verify that the bridge is enabled.

What Should I Do if the Module Fails the Self-Test?

1. Restart the system.

2. Launch MAX, and perform the self-test again.

3. Power off the chassis.

4. Reinstall the failed module in a different slot.

5. Power on the chassis.

6. Perform the self-test again.

Thermal Shutdown Error

If you receive an over-temperature or thermal shutdown error and your device shuts down,

complete the following steps to re-enable your device:

1. Power off the computer or chassis that contains the device.

2. Reinstall the device and make any necessary adjustments to make sure that the device is

effectively cooled.

3. Power on the computer or chassis.

Note The thermal shutdown error is reported until the device has cooled to an

acceptable operating temperature and has been successfully reset.

For more information about cooling the device, refer to the Maintain Forced-Air Cooling

Note to Users included in your kit.

Related Information

Installing the NI 5622 on page 4

10 | ni.com | NI PXIe-5622 Getting Started Guide

Andere Handbücher für PXIe-5622

Inhaltsverzeichnis

Andere National Instruments Messgerät Handbücher

National Instruments

National Instruments NI PXIe-4138 Handbuch

National Instruments

National Instruments SC-2345 Carrier Bedienungsanleitung

National Instruments

National Instruments NI PXIe-4139 Handbuch

National Instruments

National Instruments PXIe-5667 Bedienungsanleitung

National Instruments

National Instruments InsightCM Bedienungsanleitung

National Instruments

National Instruments NI TB-2644 Bedienungsanleitung

National Instruments

National Instruments PXIe-4163 Bedienungsanleitung

National Instruments

National Instruments PXIe-5668 Bedienungsanleitung

National Instruments

National Instruments MON-10467 Bedienungsanleitung

National Instruments

National Instruments 446 Series Handbuch

National Instruments

National Instruments NI 5102 Bedienungsanleitung

National Instruments

National Instruments PCIe-5763 Bedienungsanleitung

National Instruments

National Instruments PXIe-5630 Bedienungsanleitung

National Instruments

National Instruments Module NI PXI-8250 Bedienungsanleitung

National Instruments

National Instruments PXIe-5764 Bedienungsanleitung

National Instruments

National Instruments PXI-5142 Bedienungsanleitung

National Instruments

National Instruments PXI-5660 Bedienungsanleitung

National Instruments

National Instruments NI Vision CVS-1450 Series Bedienungsanleitung

National Instruments

National Instruments NI 9213 Bedienungsanleitung

National Instruments

National Instruments NI 5731 Series Bedienungsanleitung

National Instruments

National Instruments PXIe-5668R Bedienungsanleitung

National Instruments

National Instruments PXIe-5663E Bedienungsanleitung

National Instruments

National Instruments PXIe-6570 Bedienungsanleitung

National Instruments

National Instruments NI PXI-4070 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung