National Instruments PXIe-4162 Bedienungsanleitung

GETTING STARTED GUIDE

PXIe-4162

PXIe, 12-Channel, ±24 V, 100 mA PXI Source Measure Unit

This document explains how to install, configure, and test the PXIe-4162. The PXIe-4162

ships with NI-DCPower driver software, which you can use to program the module.

Note Before you begin, install and configure your chassis and controller.

Contents

Verifying the System Requirements..........................................................................................1

Unpacking the Kit..................................................................................................................... 1

Other Equipment....................................................................................................................... 3

Preparing the Environment....................................................................................................... 3

Installing the Software.............................................................................................................. 4

Installing the PXIe-4162........................................................................................................... 4

PXIe-4162 Pinout and LEDs.....................................................................................................6

Configuring the PXIe-4162 in MAX...................................................................................... 12

Self-Calibrating the PXIe-4162.............................................................................................. 13

Programming the PXIe-4162.................................................................................................. 14

Troubleshooting...................................................................................................................... 16

What Should I Do if the PXIe-4162 Doesn't Appear in MAX?......................................16

Why Is the ACCESS LED Off When the Chassis Is On?...............................................17

What Should I Do if the PXIe-4162 Fails the Self-Test?................................................17

Where To Go Next.................................................................................................................. 18

Worldwide Support and Services............................................................................................ 18

Verifying the System Requirements

To use the NI-DCPower instrument driver, your system must meet certain requirements.

Refer to the product readme, which is available on the driver software media or online at

ni.com/manuals, for more information about minimum system requirements, recommended

system, and supported application development environments (ADEs).

Unpacking the Kit

Refer to the following figure to identify the contents of the PXIe-4162 kit.

Figure 1. PXIe-4162 Kit Contents

PXIe-4162

OUTPUT

12-CH PrecisionSMU

ACCESS VOLTAGE

ALLCHANNEL SIGNALS

±24V MAX

60V MAX to

1. PXIe-4162

2. PXIe-4162 Safety, Environmental, and Regulatory Information

3. Maintain Forced-Air Cooling Note to Users

Notice To prevent electrostatic discharge (ESD) from damaging the module,

ground yourself using a grounding strap or by holding a grounded object, such as

your computer chassis.

1. Touch the antistatic package to a metal part of the computer chassis.

2. Remove the module from the package and inspect it for loose components or other signs

of damage.

Notice Never touch the exposed pins of connectors.

Note Do not install a module if it appears damaged in any way.

3. Unpack any other items and documentation from the kit.

Store the module in the antistatic package when the module is not in use.

2| ni.com | PXIe-4162 Getting Started Guide

Other Equipment

There are several required items not included in your PXIe-4162 kit that you need to operate

the PXIe-4162. Your application may require additional items not included in your kit to

install or operate your PXIe-4162.

Required Items

• A PXI Chassis and chassis documentation

• A PXI Controller or PC with a Device for PXI Remote Control system that meets the

system requirements specified in this guide and chassis documentation

Optional Items

• PXI Slot Blocker Kit (NI part number 199198-01)

• SHDB62M-DB62M-LL Low Leakage Cable for SMU, 62 D-Sub Male to 62 D-Sub Male

– 1 m (NI part number 142947B-01)

– 2 m (NI part number 142947B-02)

• SHDB62M-BW-LL Low Leakage Cable for SMU, 62 D-Sub Male to Bare Wire Male

– 1 m (NI part number 142948A-01)

– 2 m (NI part number 142948A-02)

• 62-Pin Connector Kit for PXIe-416x SMUs (NI part number 785582-01)

Visit ni.com for more information about these additional items.

Preparing the Environment

Ensure that the environment you are using the PXIe-4162 in meets the following

specifications:

Temperature and Humidity

Temperature

Operating

Chassis with slot cooling

capacity ≥58 W1

0 °C to 55 °C

All other compatible chassis 0 °C to 40 °C

Storage -40 °C to 71 °C

1Not all chassis with slot cooling capacity ≥58 W can achieve this ambient temperature range. Refer

to PXI chassis specifications to determine the ambient temperature ranges your chassis can achieve.

PXIe-4162 Getting Started Guide | © National Instruments | 3

Humidity

Operating 10% to 90%, noncondensing

Storage 5% to 95%, noncondensing

Pollution Degree 2

Maximum altitude 2,000 m (800 mbar) (at 25 °C ambient temperature)

Notice This model is intended for use in indoor applications only.

Related Information

Refer to the PXIe-4162 Specifications at ni.com for complete specifications.

Installing the Software

You must be an Administrator to install NI software on your computer.

1. Install an ADE, such as LabVIEW or LabWindows™/CVI™.

2. Visit ni.com/downloads/drivers and search for NI-DCPower.

3. Download the latest version of NI-DCPower by clicking Download and then running the

executable (.exe) file.

Driver support for the PXIe-4162 was first available in NI-DCPower 17.6.

4. Follow the instructions in the installation prompts.

Note Windows users may see access and security messages during

installation. Accept the prompts to complete the installation.

5. When the installer completes, select Restart in the dialog box that prompts you to restart,

shut down, or restart later.

Installing the PXIe-4162

Notice To prevent damage to the PXIe-4162 caused by ESD or contamination,

handle the module using the edges or the metal bracket.

The PXIe-4162 is a single-slot module with one backplane connector. The module may be

installed into any PXI Express-compatible slot.

1. Ensure the AC power source is connected to the chassis before installing the PXIe-4162.

The AC power cord grounds the chassis and protects it from electrical damage while you

install the PXIe-4162.

2. Power off the chassis.

3. Inspect the slot pins on the chassis backplane for any bends or damage prior to

installation. Do not install a module if the backplane is damaged.

4| ni.com | PXIe-4162 Getting Started Guide

4. Position the chassis so that inlet and outlet vents are not obstructed.

For more information about optimal chassis positioning, refer to the chassis

documentation.

5. Remove the black plastic covers from all the captive screws on the module front panel.

6. Identify a supported slot in the chassis. The following figure shows the symbols that

indicate the slot types.

Figure 2. Chassis Compatibility Symbols

NI PXIe-1062Q

12 3 45

1. PXI Express System Controller Slot

2. PXI Peripheral Slot

3. PXI Express Hybrid Peripheral Slot

4. PXI Express System Timing Slot

5. PXI Express Peripheral Slot

PXIe-4162 modules can be placed in PXI Express peripheral slots, PXI Express hybrid

peripheral slots, or PXI Express system timing slots.

7. Touch any metal part of the chassis to discharge static electricity.

8. Ensure that the ejector handle is in the downward (unlatched) position.

9. Place the module edges into the module guides at the top and bottom of the chassis. Slide

the module into the slot until it is fully inserted.

Figure 3. Module Installation

NI PXIe-1075

1. Chassis

2. Hardware Module

3. Ejector Handle in Downward (Unlatched) Position

10. Latch the module in place by pulling up on the ejector handle.

PXIe-4162 Getting Started Guide | © National Instruments | 5

11. Secure the module front panel to the chassis using the front-panel mounting screws.

Note Tightening the top and bottom mounting screws increases mechanical

stability and also electrically connects the front panel to the chassis, which can

improve the signal quality and electromagnetic performance.

12. Cover all empty slots using EMC filler panels or fill using slot blockers to maximize

cooling air flow, depending on your application.

13. Power on the chassis.

Related Information

Why Is the ACCESS LED Off When the Chassis Is On? on page 17

PXIe-4162 Pinout and LEDs

Front Panel

Refer to the following figures and tables for information about the PXIe-4162 front panel

connector pins, channels, and LEDs.

PXIe-4162

OUTPUT

12-CH Precision SMU

ACCESS VOLTAGE

ALL CHANNEL SIGNALS

± 24V MAX

60V MAX to

6| ni.com | PXIe-4162 Getting Started Guide

Item

A LED Access Status indicator

B LED Voltage Status Indicator

Table 1. LED Access Status Indicator

Status Indicator Device State

(Off) Not Powered

Green Powered

Amber Device is being accessed

Table 2. LED Voltage Status Indicator

Status Indicator Output Channel State

(Off) All device outputs are disconnected from their voltage generation sources

through output disconnect relays.

Green At least one device output is connected to a voltage generation source.

Red The device has a fault or is in error due to the voltage generated or

measured by the device. Refer to the driver software for possible sources.

The device will not operate until the error is cleared and/or the device is

reset.

Pinout

The following figure and table provide detailed signal information for the PXIe-4162

connector.

PXIe-4162 Getting Started Guide | © National Instruments | 7

CH1 Output HI

CH1 Sense HI

CH10 Sense LO

Calibration HI

CH10 Sense HI

CH10 Guard

CH10 Output HI

CH7 Guard

CH7 Sense LO

CH7 Output HI

CH7 Sense HI

CH0 to 11 Output LO

CH4 Guard

CH4 Sense LO

CH4 Output HI

CH4 Sense HI

CH1 Sense LO

CH1 Guard

CH0 Output HI

CH0 Sense HI

CH2 Guard

CH2 Sense LO

CH3 Output HI

CH3 Sense HI

CH5 Guard

CH5 Sense LO

CH6 Output HI

CH6 Sense HI

CH8 Guard

CH8 Sense LO

CH9 Output HI

CH9 Sense HI

CH11 Guard

CH11 Sense LO

CH0 Guard

CH0 Sense LO

CH2 Output HI

CH2 Sense HI

CH3 Guard

CH3 Sense LO

CH5 Output HI

CH5 Sense HI

CH6 Guard

CH6 Sense LO

CH8 Output HI

CH8 Sense HI

CH9 Guard

CH9 Sense LO

CH11 Output HI

CH11 Sense HI

8| ni.com | PXIe-4162 Getting Started Guide

Table 3. PXIe-4162 Signal Descriptions

Bundle Channel Pin Signal Description

A 0 62 Output HI

61 Sense HI

41 Sense LO

42 Guard2

1 20 Output HI

19 Sense HI

17 Sense LO

18 Guard2

2 39 Output HI

38 Sense HI

59 Sense LO

60 Guard2

B 3 57 Output HI

56 Sense HI

36 Sense LO

37 Guard2

4 15 Output HI

14 Sense HI

12 Sense LO

13 Guard2

5 34 Output HI

33 Sense HI

54 Sense LO

55 Guard2

2Guard terminals are not supported in the highest current ranges: 60 mA or 100 mA.

PXIe-4162 Getting Started Guide | © National Instruments | 9

Table 3. PXIe-4162 Signal Descriptions (Continued)

Bundle Channel Pin Signal Description

C 6 51 Output HI

50 Sense HI

30 Sense LO

31 Guard2

7 9 Output HI

8 Sense HI

6 Sense LO

7 Guard2

8 28 Output HI

27 Sense HI

48 Sense LO

49 Guard2

D 9 46 Output HI

45 Sense HI

25 Sense LO

26 Guard2

10 4 Output HI

3 Sense HI

1 Sense LO

2 Guard2

11 23 Output HI

22 Sense HI

43 Sense LO

44 Guard2

A, B, C, D 0 to 11 10 Output LO

10 | ni.com | PXIe-4162 Getting Started Guide

Andere Handbücher für PXIe-4162

Inhaltsverzeichnis

Andere National Instruments Messgerät Handbücher

National Instruments

National Instruments USB-TC01 Bedienungsanleitung

National Instruments

National Instruments NI PXIe-5105 Bedienungsanleitung

National Instruments

National Instruments PXI-5661 Bedienungsanleitung

National Instruments

National Instruments PXIe-5603 Bedienungsanleitung

National Instruments

National Instruments NI 5731 Series Bedienungsanleitung

National Instruments

National Instruments NI Bedienungsanleitung

National Instruments

National Instruments CMS-9024 Bedienungsanleitung

National Instruments

National Instruments NI 9775 Bedienungsanleitung

National Instruments

National Instruments PXIe-4163 Bedienungsanleitung

National Instruments

National Instruments 446 Series Handbuch

National Instruments

National Instruments PXIe-5668R Bedienungsanleitung

National Instruments

National Instruments PXIe-6570 Bedienungsanleitung

National Instruments

National Instruments NI 9223 Handbuch

National Instruments

National Instruments PXI-5152 Handbuch

National Instruments

National Instruments PXIe-5654 Handbuch

National Instruments

National Instruments PCIe-5763 Bedienungsanleitung

National Instruments

National Instruments PXI-4070 6 1/2 Digit FlexDMM Handbuch

National Instruments

National Instruments NI 5911 Bedienungsanleitung

National Instruments

National Instruments NI 6601 Bedienungsanleitung

National Instruments

National Instruments MON-10467 Bedienungsanleitung

National Instruments

National Instruments PXI-5660 Bedienungsanleitung

National Instruments

National Instruments FD-11603 Bedienungsanleitung

National Instruments

National Instruments 9219 Handbuch

National Instruments

National Instruments PXIe-4163 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung